Description
Error: Contact form not found.
Microcontroller Based Distance Impedance Relay Trainer
It consists of many components i. Transmission line module ii. Voltage and current signal conditioners iii.Distance Relay iv. Multifunction Meters
Transmission Line Module
• Total line length – 180Km
• Modeled by RL – parameters
• Current rating – max 5A
• Voltage rating – max 250V AC
Voltage and Current Signal Conditioners
• One no of 5A/5V current transformer is provided to read the relay current input
• One no of 230V/9V potential transformer is provided to read the relay voltage input
Distance Relay
• One PIC microcontroller used as processor to activate the relay function
• One LCD to indicate :
– Impedance set value
– Current & voltage value
– Set time, Relay tripping time
• Four numbers of keys are used
• Parameters
– Current input : 0-5Amps, Voltage input : 0-230V AC
– Number of contact: One number of NO contact @ 220V, 10Amp rating
– Auxillary supply : 230V AC, 50Hz
Multifunction Meter
• One MFM provided for measuring input side all parameters (V, I, PF, F, AVR, KW)
• One MFM provided for measuring load side line parameters
Related products
Three Phase Transmission Line Fault Analysis Trainer
Three phase Transmission line fault Simulation Study Module
Specification
• 3 phase power supply from 3 phase generator • To simulate 3 phase balanced system fault and unsymmetrical faults • Fault study with single line and double line in 3 phase system • Faults : - L-G-Fault - L-L-Fault - L-L-G-Fault - Single Conductor open fault - Double Conductor open fault - Fault through impedance • Theoretical calculations and verification with practical results. • The transmission lines are simulated by high frequency Inductance & resistance for short, medium and long line.
Microcontroller Based Differential Relay
This test set-up consists of a. Microcontroller based differential relay. b. 300VA transformer set-up
Specification
• One PIC Microcontroller used as processor to read all current, (PY, SY) & activation of relay function • One LCD to indicate, - Set value, All currents - Set time, DMT/IDMT type - Relay tripping time. - Biased/Unbiased type status • Four numbers of key used - To select IDMT/DMT type or biased un-biased type - Set current value adjustment - Set time adjustment - Reset function • Six 5A CT used to sense primary and secondary current. • One 12V TPTT auxiliary relay used for contactor operation. • Specification: - Current input : 0-5Amp - Voltage input : 0-230V - Number of contact : Three number No contact @ 220V, 10Amp rating. - Auxiliary supply : 230VAC, 50Hz • PC interfacing facility power ON/OFF switch with indicator. • Make : VI MICRO • Model : VPL - 83A
Electro Mechanical Type Over Voltage Relay Study Trainer
This test set-up consists of a. Electromechanical over voltage-relay. b. Relay test setup with meter.
Electromechanical over voltage-relay
• One electromechanical type over voltage relay - Make: Megawin - Voltage setting multiplier (121V, 132, 143, 154, 165, 176, 187V) - Time setting multiplier. - One “NO” contact @ 220V, 10Amp rating. - One “NC” contact @ 220V, 10Amp rating. b. Relay test setup with meter • One 0-300V, 1AMP variable AC source provided for relay coil. • One auto transformer provided for AC voltage adjustment. • One illuminated rocker switch provided for power ON/OFF. • One digital voltmeter used to indicate applied voltage. • One digital timer provided for relay tripping time measurement. • One automatic relay tripping time measurement circuit. • One start/stop push-to on switch provided for time measurement circuit. • One reset switch provided for timer reset.
Reviews
There are no reviews yet.