Description
[contact-form-7 404 "Not Found"]
Multiple Input/Output Process Trainer
Panel Features
• Power ON/OFF switch
• Heater selection switch
• Heater and pump indicators
• High current fuse carrier for
• Heater protection
• Provision to run the stirrer
• Digital panel meters
• Two numbers of industrial PID Controller
• Electrical test points are provided to measure the current signal
• Mimic Diagram
Features
• Two numbers of flow Transmitter (DPT) are provided to sense the flow of the liquid.
• Three numbers of temperature transmitter (RTD) are provided at various stages to measure the temperature.
• Five numbers of level sensor (RF capacitance) are provided to sense the level of each tank.
• Industrial type Conductivity sensor is provided to analyze the conductivity of given Solution.
• RTD sensor (or) Thermocouple acts as a temperature sensor.
• Digital panel meters are provided to indicate the output of each sensor.
• Provision to measure the conductivity.
• Two numbers of motorized control valve or pneumatic control valve are provided to control the flow of the pipe line.
• A powerful thyristor based power driver is provided to drive the heater power.
• An industrial type water heater is used as a heat Source.
• Storage tank of 50 litre capacity (SS).
• Process tank of 15 litre capacity (SS).
• Four numbers of acrylic tank are provided to study the response of four tank systems.
• In necessary location Ball valve, globe valve and needle valves are provided.
• Two numbers of stirrer are provided in the temperature process and alkaline process.
• Three numbers of centrifugal pump (FHP) is used to circulate the water from storage tank.
• Six numbers of rotameter are provided in the process inlet to visualize the real flow.
• Regulated power supply is mounted in the panel.
• All the flow lines are fitted by (SS) pipe fitting.
• An over head tank is provided to give constant flow.
• All the equipments are mounted in a rugged and mobile type metallic work station.
Related products
Pressure Process Station
Panel Features
• Digital Panel Meters. • Mimic diagrams. • Pressure gauges are provided, wherever necessary.Softwares
• MATLAB • LabVIEW • PLC • C/VB CompatibilityFeatures
• The Pressure process station is an attractive module comparing to the Analyzer and Laboratory trainer. • All are the industrial standard (4-20)mA interfacing signals. • It provides a real industrial feeling of the process to the students. • A Piezo Resistive Pressure Transmitter (0-7)Bar is used to sense the pressure. • An Electronic Regulated Power supply is fixed for voltage Regulation. • An electro pneumatic converter is mounted to control the pneumatic control valve. • A globe Pneumatic Control Valve for controlling flow of air. • An air regulator cum filter is provided for Air regulation. • A two separate pressure tank is provided as process tank with pressure gauges and relief valves. • All the air flow lines are fitted by flexible hoses/fittings for better reliability. • Hand valve provisions are given for series, parallel connection of pressure tanks. • USB/Serial port data acquisition is provided.
Multi Tank System
Panel Features
• Rocker switch is provided to ON/OFF the process plant. • Digital Panel Meter. • Pump Indicator. • Short Circuit protection. • Mimic diagram in the panel. • All the electrical connectors are terminated in the panel.Features
• This equipment consists of four tank system, conical tank system and spherical tank system. • Four numbers of Acrylic tank are provided for doing multivariable control of four tank system. • Conical tank (SS) is provided to performing the nonlinerar control system. • Spherical tank (SS) is provided for controlling the complex system. • Six numbers of level transmitter (DPT) are provided to measures the level of the each tank. • Three numbers of smart control valve with positioner are provided in the inlet of Flow rate. • Hand valve is provided at the bottom of the process tank to study the load disturbance. • Three numbers of hand valve are provided to control the Rotameter flow rate. • Three numbers of centrifugal pump are provided for water circulation. • Two flow transmitters are mounted for conducting flow, cascade and Ratio control. • Appropriate Digital panel meters are provided to measure the transmitter and actuator signals. • Delay coils are provided to the input of the process tanks for transportation lag study. • Storage tank of 100 litre capacity (SS). • Rotameter for Visual indication of the flow rate. • Relay circuit is provided to ON/OFF the solenoid valve. • Built in regulated power supply. • All Water flow lines are connected by (SS) fittings. • Necessary patch chords are provided for interfacing the Electrical signal. • Established successful design that mimics a real industrial process. • Front panel includes mimic diagram of the process, so students can clearly see what they are controlling. • Safe, practical and realistic. • Hand valves are provided to study the coupling (Interaction) and decoupling
Level Process Station
Panel Features
• Digital Panel Meters. • Mimic diagrams. • Pressure gauges are provided, wherever necessary. • Level switches are provided for overflow indication.Features
• The Level Process Station is an attractive module. • All are the industrial (4-20) mA standard interfacing signals. • It provides a real industrial feeling of the processes to the students. • A RF Capacitance level transmitter is used to sense the level (700mm) of tank. • An Electronic Regulated Power supply is fixed for voltage regulation. • An Air regulator cum filter is provided to regulate the air pressure. • An Industrial standard electro pneumatic converter is mounted to control the control valve. • A Globe pneumatic control valve is used to control the flow rate • All the air flow lines are fitted by flexible hoses/fittings for better reliability. • A Rotameter (1000 LPH) is provided for Visual Indication of flow rate. • A Transparent Process Fiber tank (800mm) with graduated level scale. • A Solenoid Valve is provided for Load Disturbance study. • A Rust proof Reservoir Tank (SS) capacity of 45 Liter. • By pass line is provided to avoid pump over loading. • A Centrifugal Pump is used for water circulation. • All components are fixed in a mobile rack. • All water flow lines are fitted by SS pipes. • USB/Serial port data acquisition is provided.
Level Process Controller
Features
• It is a miniature version and occupies less space. • A RF capacitance Level Transmitter is used to sense the tank level. • An Industrial standard electro pneumatic converter is used to control the control valve. • A Pneumatic control valve is used to control the Level of the tank. • A Process tank of 3 liter capacity with graduated level scale. • A Rust proof reservoir tank (SS) capacity of 8 liters. • A centrifugal pump is provided for water circulation. • An air Regulator cum filter of capacity (0-2.1) Bar is provided to regulate the Air pressure. • Bypass line provision is provided to avoid pump over loading. • Hand valve provision is provided to make the disturbance study. • All the water flow lines are fitted by SS pipes. • USB/Serial port data acquisition is provided.
Reviews
There are no reviews yet.