Description
Error: Contact form not found.
Emissivity Measurement Apparatus
The apparatus consists of a test plate and a comparator. A black plate is used as a comparator for test plate. When all the physical, dimensions and the temperatures are equal, heat losses from both plates will also be the same, except radiation losses. Hence the input difference will be due to difference in emissive. Both the plates are kept in a panel enclose with perplex front and are given inputs through separate dimmerstats so that temperatures of both can be kept equal. Thus emissivity can determine over a wide range of temperatures.
SPECIFICATIONS:
1.Test plate and Black plates — 160mm. Dia. Aluminum plates, mounted in Panel with mica heater inside.
2.Instrumental panel consisting of-
a)Voltmeter and ammeter for input measurement to both heaters through a selector switch.
b)Separate dimmers for both the plates.
c)Multichannel digital temperature indicator.
A technical manual accompanies the unit.
SERVICES REQUIRED:
1.Space area of 1.5m x 1 m. at working height.
2.230v, 15A, AC supply with earthing connection
Related products
Thermal Conductivity Of Insulating Powder
The apparatus consists of an insulating powder, which is enclosed in a cavity of two concentric spheres. The inner space of the inner sphere contains the mica heater. Input to the heater can be adjusted by the dimmerstat. The tappings on the surfaces of the inner sphere and outer sphere are used to find out the temperature difference between the spheres. This enables to find out the conductivity of powder.
Specifications:
1.Inner sphere dia. 100mm and outer sphere dia. 200mm. 2.Mica heater two heat the inner sphere surface. 3.Ten thermocouple tappings in the test section. 4.Plaster of Paris / asbestos powder in the test section. 5.Panel comprises of a)Voltmeter and ammeter b)Dimmerstat c)Temperature indicatorServices required:
1.220v stabilized single-phase supply. 2.Floor surface 1m x 0.5m at working height.
Pin Fin Appatatus
The apparatus consists of a channel in which the pin fin is tested in both natural as well as forced convection. The channel is connected to the suction of blower. The blower is operated to touch the pin fin in forced convection only. In natural convection, the window above the pin fin is kept open to the atmosphere. Five thermocouple tapings are given along the length of the fin. Thus the temperature distribution along the length can be distinguished. Also natural and forced heat transfer co-efficient, effectiveness, etc. can be found out.
Specifications:
1.Three pin fins- a) M. S. b) Brass c) Al 2.Channel- 150mm x 100mm x 1000mm 3.Blower – run by f.h.p. motor. 4.Orifice meter along with water manometer to measure airflow. 5.Voltmeter and ammeter to measure power input. 6.Cr- Al thermocouple with 6 tapings along with temperature indicator. 7.Dimmerstat to control power input. 8.A band heater to heat the pin fin. A technical manual accompanies the unit.Services required:
1.220v, stabilized single phase supply along with earthing Connection. 2.Floor area 2m x 1m x 1m height.
Composite Walls Apparatus
Composite Walls Apparatus:
The apparatus consists of a pair of M.S. plates, Bakelite, brass/aluminum. These plates in series on either side of the heater form a composite wall. The whole unit is clamped in a frame, which can be viewed through the Perspex sheet. The thermocouple tapings enables us to find out the conductivity and resistance of the composite walls.
SPECIFICATIONS:
1.Heater- Mica healer of dia. 250 mm. 2.Plates- a) M.S. plates of thickness 25mm & dia. 250mm.-2 nos. b) Bakelite plates of thickness 10mm & dia. 250mm.-2 nos. c)Brass/Aluminum plates of thickness 15mm & dia. 250mm.-2nos 3.Dimmerstat – 2 A capacity. 4.Measurements — a) voltmeter and an Ammeter to measure input power. b) Multichannel digital temperature indicator to measure temperatures at- various points. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, A.C. stabilized supply along with earthing connection. Bench area Im x lm x 0.5m height
Critical Heat Flux Apparatus
The apparatus demonstrates the regimes of pool boiling. The test section consists of a test wire surrounded by water of constant temperature. The surface temperature of the test wire is heated by passing current through it. Due to the temperature difference between the wire surface and surroundings, the difference regimes are observed till the burnout point.
Specifications:
1.Test wire -35 gauge or 40 gauges. Length = 10cm. 2.Nichrome heater- 1 kw capacity – 1 nos. 3.Glass trough of sufficient capacity. 4.Table light to observe the test wire. 5.Voltmeter and ammeter to measure the input to the test wire. 6.Dimmerstat to adjust the voltage. A technical manual accompanies the unit.SERVICES REQUIRED:
1.220v, ISA, stabilized single-phase supply. 2.Floor surface- 1m x 1m at working height.
Forced Convection Apparatus
The unit consists of a circular pipe; loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe. Temperature of air at inlet and outlet of test section are measured. Thus the students can calculate local and overall heat transfer coefficients in forced convection, at various airflow rates and various heat flux values.
SPECIFICATIONS:
1.Test pipe – 32mm NB GI pipe, 500 mm. long, heated by band heater, outside. Centrifugal blower to force air through test pipe with How control valve. 2.Variac 2A, capacity to force air through test pipe with flow control valve. 3.An orifice meter with differential water manometer. 4.Voltmeter and Ammeter to measure heater input. 5.Multichannel digital temperature indicator to measures various temperatures. 6.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of about 1m. x 0.75 m. at working height. 2.239v, 15A, AC, supply with earthing connection.
Natural Convection Apparatus
The unit consists of a vertical brass pipe heated by a cartridge heater inside it. The pipe looses heat to atmosphere by natural convection. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter. Thus students can determine overall heat transfer coefficient and local transfer coefficients in natural convection at various heat transfer rates.
SPECIFICATIONS:
1.Pipe – Brass pipe, 38mm. dia. (OD) 500mm. long, fitted with cartridge heater inside. 2.Thermocouples are fitted along with the length of pipe for Temperature measurement – 7 nos. 3.Enclosure 200mm. x 200mm. x 800mm. size, with one side of Perspex sheet. 4.Measurements & Controls a) A Dimmerstat for heater input control. b) Voltmeter and Ammeter for heater input measurement. c) Multichannel digital temperature indicator. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of 1.5m x 0,75m. at working height. 2.230v, 5A, AC, electric supply with earthing connection.
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
Thermal Conductivity Of Metal Rod
The apparatus consists of a copper bar, which is heated at one end, a heat sink is provided at other end. The test section of bar is properly insulated and thermocouples are attached along the length of bar. Heat conducted through the section of bar is measured by heat collection in water-cooled heat sink. A panel comprising of controls and measurements is provided, which provides easy operation and sturdy mounting of unit.
Reviews
There are no reviews yet.