Description
[contact-form-7 404 "Not Found"]
Resistance Units, Interlocking
Description
in plastic case 57 x 25 mm (diameter x depth)with 4 mm terminals, one of which is fitted with a copper slotted lug for being connected to another unit, non inductively wound, adjusted to ±0.1% of nominal value
| Ohms | ||
|---|---|---|
| 0.1 | ||
| 0.2 | ||
| 0.5 | ||
| 1 | ||
| 2 | ||
| 5 | ||
| 10 | ||
| 20 | ||
| 50 | ||
| 100 |
Related products
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
Earth, Neutral And Live Board Demonstration
Description
This apparatus is an effective demonstration of how the earth wire and fuse act together to protect both the user and the appliance. When the appliance is connected correctly and the LEDs in the appliance will illuminate to show the appliance is working. A fault is then demonstrated by swapping the live wire from inside the appliance to the case to show either the fuse melts (protecting the user and appliance) or in the case of no earth wire, the LEDs illuminate to indicate the passage of current through the person to ground. The fuse is easily visible and can be seen to ‘blow’ when a fault occurs.The unit is supplied with 10 m of fuse wire and full instructions. A 12 V DC power supply is required. Connections are made via 4 mm shrouded sockets.
Circuit Breaker Demonstration
Description
Investigate the working principle of circuit breaker type fuse with this demonstration model. The apparatus is built on a robust plastic base and includes resistive loads to simulate external wiring circuits. Applications of the thermal response of bimetal strips and also electromagnetism (movement from a solenoid) are clearly demonstrated in this model. When a 12 V DC supply is connected (not supplied) the LED lights to show that current is flowing in the external circuit and the bi-metal strip can be seen to bend as its heater coil raises the temperature. After a few minutes the bending is sufficient to trip the mechanism and the current path is broken. At any current selection a short circuit situation can be initiated by pressing the red button and this produces an immediate response from the solenoid to disconnect the supply.
Transformer Stand and Core
Description
Apparatus is designed primarily for demonstration of the basic principles of transformers. It consists of a laminated U-core with laminated I-core, both with 32 x 25 mm cross section to form a closed core of size 102 x 127 mm. Heavy aluminium alloy stand with removable clamping rods, 2 pole pieces, each 65 x 30 x 25 mm with one end cone shaped, to accept support rod and shading ring. Poles also have a hole drilled through lengthwise to take a light beam. 300 turns 600 turns 1200 turns 3600 turns 12000 turns
Reviews
There are no reviews yet.