Description
[contact-form-7 404 "Not Found"]
Tablet Making Machine (Hand Operated)
Details
Single punch automatic compression and injection device with each revolution of the wheel drive automatic feed and remove of tablets.
Built on heavy cast body with centric pressure system SS hoper provided and connected by a rubber tube easy setting for thickness and hardness of tablets with nuts and locknuts.
Features
Easily rotating wheel for making tablets.
Compressing lever for adjustable harness of tablets.
Adjustable lower punch for adjusting the thickness.
Stainless steel day and punch size 6, 9, 12 mm.
Electrical model can be provided in same with ½h.p motor.
Related products
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Orbital Shaking Incubator
Specification
Outer made of M.S. Sheet powder coated & inner chamber is made of thick S.S. Sheet. The gap between two walls is fitted with high grade glass wool. The glass window makes it possible to inspect specimen without disturbing inner Temperature. The unit has a temprature range from ambient to 60°. Temperature is controlled by Dual Display Microprocessor PID Digital Temperature Indicator Cum Controller with a accuracy of + 0.5°C. Air Circulation Fan is provided to maintain stability throughout. Speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S. Sheet with Lotus type clamps to hold flasks. Unit is fitted with Digital RPM Meter, 999 min digital time.Optional Accessories
Timer 0-24 Hours. 16 Flasks of 100ml. instead of 9 flasks of 250ml. 9 Flasks of 500ml or 25 flasks of 100ml instead of 16 flasks of 250ml. 25 Flasks of 250ml or 36 flasks of 100ml instead of 16 flasks of 500ml.Size
9 Flasks of 250ml. 16 Flasks of 250ml. 16 Flasks of 500ml.
Disintegration Test Unit
Features
Digital timer with 1 second resolution. Accurate time out provided by microprocessor based time totalizer. Baskets move Up & Down as per IP/USP test specifications. Temperature Controlled by sensitive thermostats. Digital Tablet Disintegration Apparatus is designed for accurate estimation of disintegration time of tablets as per IP/USP standards. The instrument is designed to test to batches of six tablets, simultaneously. The unit consists of two beakers having capacity of 1000 cc each. In these beakers, suitable disintegration media can be taken. These can be temperature controlled using a in-built heater and a highly thermostat fitted inside the instrument. Microprocessor based time to talizer is provided for accurate time readout.Specifications
System :Digital Tablet Disintegration Apparatus. Up and Down Speed:30 rpm ± 2 rpm. Accuracy: 2% Resolution:1 sec. Operating Temp. Range:0 - 100°C Power:230V ± 10%, 50Hz.AC
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.
Permeability Cup
(S.S 304) 120mm Dia. Permeability cups for determining the water-vapor transmission of paints, varnishes, coatings, coating systems and related products.
The Permeability cup consists of a cup, seal ring and cover ring.
The seal ring is designed to prevent turning when closing the cover.
The Permeability cup is suitable for testing both self-supporting coating and non-self-supporting coatings. Water-vapor transmission is of interest for high humidity conditions.
The wet cup method is thus the reference method for determining water-vapor transmission, if agreed up on otherwise, other procedures or conditions the dry cup method may be used.
Reviews
There are no reviews yet.