Description
Error: Contact form not found.
Bulk Density Apparatus
Specification
Material :Stainless Steel
Bath Dimension (inch): 9X6X8
Product Description
Bulk Density Apparatus
Features
Dongles Bag
Durability
High tensile strength
Rust proof body
Accurate results
Related products
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Distillation Plant (Manasty Type), Wall Hanging
The unit is recommended for making pyrogen fee distilled water of a very high degree of purity, Made out of S.S. special kettle element is fitted with Ejection Device / Auto cut for safety of the element is provided water supply is stopped.
The cork fitted to the unit is of brass C.P.A. wall Mounting clamp is provided with the unit.
Supplied with cord and plug to work on 220/240 volts A.C. Stainless Steel, Output approx. 3/4 Ltr./Hr.
Stainless Steel, Output approx. 5/6 Ltr./Hr.
Aluminium Dicasted, Output approx. 3/4 Ltr./Hr.
Aluminium Dicasted, Output approx. 5/6 Ltr./Hr.
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.
Bacteriological Incubator
Specification
Standard Double Wall Fabrication, inner & outer chamber made of thick mild steel sheet. Painted with hammer tone paint finish. The gap between the walls is fitted with special grade glass wool. Provided with two or three removable shelves. Heating elements provided on three sides to attain quick and uniform heating in range of 30°C to 110°C + 1°C controlled by hydraulic type capillary thermostat. An L- Shaped prismatic thermometer is fitted to the unit for reading the chamber temperature. Equipment suitable to be working on 220V AC 50Hz single phase.Optional
Air circulating fan. Timer 0-24 hours.| Chamber Size In mms | Chamber Size | Cap. (App.) |
|---|---|---|
| 300x300x300 | (12"x12"x12") | 28L |
| 350x350x350 | (14"x14"x14") | 45L |
| 400x400x400 | (16"x16"x16") | 65L |
| 450x450x450 | (18"x18"x18") | 95L |
| 600x450x450 | (24"x18"x18") | 125L |
| 600x600x600 | (24"x24"x24") | 224L |
Reviews
There are no reviews yet.