Description
Error: Contact form not found.
Conductors and Insulators
Description
To distinguish between the conductors and insulators.
Kit contains five strips of different material (wood, acrylic, copper brass and aluminium), one lamp and one 9 V battery mounted on plastic base.
Related products
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.
Demountable Transformer
Description
This heavy duty demountable transformer can be used for the study of transformertheory and many other alternating current phenomena. This kit consists of: 1. A magnetic circuit made of highly permeable U shape metal sheet, which can be closed using two clamps with tightening screws. 2. Section: 40 x 40 mm with 150 mm length and 170 mm height. 3. One coil of 6000 turns with maximum current of 0.2 A. Intermediary coil of 2000 turns output. 4. One coil of 600 turns with maximum current of 2.5 A, which is mainly used to create the primary of transformer. 5. One coil of 1200 turns with maximum current of 1.25 A, fitted with intermediary 400 and 800 turns outputs. 6. One coil of 72 turns with maximum current of 12 A, fitted with intermediary 6, 30, 54 and 66 turns outputs. 7. Power supply cable.
Circuit Breaker Demonstration
Description
Investigate the working principle of circuit breaker type fuse with this demonstration model. The apparatus is built on a robust plastic base and includes resistive loads to simulate external wiring circuits. Applications of the thermal response of bimetal strips and also electromagnetism (movement from a solenoid) are clearly demonstrated in this model. When a 12 V DC supply is connected (not supplied) the LED lights to show that current is flowing in the external circuit and the bi-metal strip can be seen to bend as its heater coil raises the temperature. After a few minutes the bending is sufficient to trip the mechanism and the current path is broken. At any current selection a short circuit situation can be initiated by pressing the red button and this produces an immediate response from the solenoid to disconnect the supply.
Reviews
There are no reviews yet.