Description
[contact-form-7 404 "Not Found"]
Dynamo
Description
With driving wheel, to generate current, mounted on polished wood base with driving wheel in vertical position, a lamp holder and a lamp.
Output DC Current
Output both DC and AC current
Related products
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
St. Louis Motor Demonstration
Description
Students can explore how a simple electric motor works by doing a series of investigations. This St. Louis motor can be adjusted so students can study the effect of voltage and position of the brushes on the commutator. The motor consists of a two pole DC armature. The brush holder, with two heavy binding post terminals, can be rotated for experiments. The permanent bar magnets, supported by clamps, can be adjusted to the desired location. This apparatus requires 4 D cell batteries with holder (not included) or a power supply and two connecting leads (not included).
Westminister Electromagnetic Kit
Description
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.
Circuit Breaker Demonstration
Description
Investigate the working principle of circuit breaker type fuse with this demonstration model. The apparatus is built on a robust plastic base and includes resistive loads to simulate external wiring circuits. Applications of the thermal response of bimetal strips and also electromagnetism (movement from a solenoid) are clearly demonstrated in this model. When a 12 V DC supply is connected (not supplied) the LED lights to show that current is flowing in the external circuit and the bi-metal strip can be seen to bend as its heater coil raises the temperature. After a few minutes the bending is sufficient to trip the mechanism and the current path is broken. At any current selection a short circuit situation can be initiated by pressing the red button and this produces an immediate response from the solenoid to disconnect the supply.
Reviews
There are no reviews yet.