Description
Error: Contact form not found.
IPM Based Power Module
Power Module is designed for Motor control Applications upto 3 HP by using IGBT & DIODE Technology Based IPM. Input:1 Phase / 3 phase 50 Hz AC. Output : 400V/10A (MAX), AC/DC on each Leg of 3 phase Bridge
FEATURES:
• 1200V, 25A, 3 Phase IGBT Inverter Bridge
• 1200V, 10A IGBT for Over Voltage breaking
• Built – in Over Voltage, Under Voltage, Over Current & Over Temperature Protection
ADDITIONAL FEATURES:
• 1200V, 25A Converter Bridge for AC-DC power conversion
• 4 Nos of Hall Effect current sensors are provided to sense the DC Link current & 3 output current of the Inverter Bridge
• 1 No of Hall Effect Voltage sensor is provided to sense DC Link voltage
• All the PWM signals are isolated using Opto Isolator
• Protection circuit for over current with LED indication
• Optically Isolated Fault signal from the IPM is given to the Embedded/DSP controllers for protection.
• Independent Power supplies for all Isolated circuits.
• 0-900V Voltmeter is provided to Indicate the DC Link Voltage
• All current, PWMS & Feedbacks are terminated at Front panel
• FRC Connectors are provided to Interface with the Embedded/DSP controllers
• All the Input/output Lines are terminated at Banana sockets.
Related products
10KW IGBT Based Power Module
FEATURES:
• 1200V/ 75A, Peak Semikron based IGBT module • 8 Nos of IGBT’s provided with independent eight driver (inbuilt opto isolator) • All the collector and emitter terminals are brought out of proper connectors for power circuit connection • All the gate and emitter terminals are brought out and terminated on front panel to view driver output fault output • Indicator LED provided for PWM input and power supply input • Proper heat sink provided for all the IGBTs with cooling fan provision • All are enclosed by viewable acrylic cabinet • Temperature sensor provided for over temperature Protection • PWM inputs are brought out on Front Panel, you may connect any controller for interface • One common +15V Power supply for all the driver circuit, Inbuilt isolated power supply provided. • Over current protection and short circuit protection provided for all individual IGBT module • Reset circuit provided and terminated to clear the fault • Snubber capacitor provided for dv/dt protection for all IGBT module • 60A 3 phase bridge rectifier and filter circuit available for power circuit input.
3Ø – 3Ø Matrix Converter
FEATURES:
• 9 No. Bi-directional Switch with IGBT and Fast Diode Bridge,Rating@1200V 50A Forms 3 Phase to 3 phase Matrix Converter Power Circuit • Output of Matrix Converter Terminated by Banana Connector in the Front Panel • 9 No. High Speed Opto- IC Provided for Gate PWM Isolation. • 9 No. Single Channel IGBT Driver IC with Current Limiting Facility Provided for IGBT Gate Driving. • 9 No. 15V DC Power Supply Provided Internally for Control Circuit. • 3 No. Inductor and AC Capacitor Provided for Three Phase Input Filter. • One No Three Phase Synchronizing Transformer (230/9V) Provided for three Phase Supply Synchronization • 6 nos Hall-effect Current Sensor with Signal Conditioning Circuit Provided for Output and Input Current Measurement and Protection. • AC voltmeter is provided for measure the input AC voltage. • +/- 15V DC Internally Provided for Sensor Signal Conditioner Circuits. • MCB Provided for Input power ON/OFF and OL Protection ON/OFF Switch. • Test points are provided on the front panel to measure the voltage, current and PWM signals • 34 pin FRC Connector Provided for IGBT Gate PWM Inputs. • Input : Three Phase 440V AC, 50 Hz. • Output : Three Phase Variable Voltage, variable frequency • Rating : Suitable for 1 HP 3Ø AC Induction Motor
Cyclone IV FPGA Controller
FEATURES:
• Based on Altera family Cyclone IV, Device : EP4CE30 • One 34 pin header used for IPM Interface. - 16 PWM output - 8 capture inputs. • One 26 pin header ADC. - 4 channel 1MSPS ADC. - Total 8 channel using 2 Nos of ADC. - 12 bit resolution. - Input range -10V to 10V / -5V to 5V. • One 5 pin phoenix connector DAC - 4 channel DAC, 12 bit resolution. - Output range -10V to 10V / -5V to 5V. • 8 output Light Emitting Diodes (LEDs). • 8 input slide Switches. • 4 user push button switches. • 2-user limit switch. • 20 x 4 Alphanumeric LCD display. • On Board Isolated JTAG Programmer Compatible with QuartusII software. • Isolated USB (USB to Serial) interface. • 3 Nos of 20 pin header each have 16 IOs.
Reviews
There are no reviews yet.