Description
Error: Contact form not found.
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece.
The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.
SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height
[2] Orifice – 8mm and 10 mm.
[3] Mouthpiece
(a) LID = 4
(b) L/D = 1
(c) Bordas mouthpiece.
(d) Convergent mouthpiece.
[4] X-Y gauge for orifice jet co-ordinates.
[5] Measuring tank of suitable capacity OR a calibrated water flow meter.
[6] Sump tank of suitable capacity.
[7] 0.5 HP pump with valve.
A technical manual accompanies the unit.
SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height.
[2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.
Related products
Discharge Over Notches Apparatus
DESCRIPTION:-
The Lab setup consists of a channel having sufficient length and width in which water is supplied from the bottom. Required Notch is fitted at one end of this channel .A hook gauge with Vernier scale is fitted to measure the height of fluid in flow channel. Arrangement for fixing interchangeable notches is made. Set of three brass notches, i.e. rectangular notch. 60 V notch & 45 V notch provided along with the set up. Present set – up is self –contained water re- circulating unit .provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass value are fitted in water line to conduct the experiment on different flow rate .Flow rate of water is measured with the help of measuring tank and stopwatch.EXPERIMENTS:-
Ø To Determination Co-efficient of discharge (Cd) through Ø V notch (45 deg. and 60 deg.) Ø Rectangular Notch. Ø Trapezoidal NotchUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity 0.5kw,220V AC, Single PhaseTECHNICAL SPECIFICATION: –
Ø Channel Test Section : Size 600x250x180 mm Ø Notches : Material Brass(3 Nos) 1. Rectangular Notch 2. 45 deg. V Notch 3. 60 deg. V Notch 4. Trapezoidal Notch Ø Hook / Pointer : With Vernier Scale Ø Water Circulation : FHP Pump, Crompton/Sharp make. Ø Flow Measurement : Using Measuring Tank with Piezometer, Cap.25 Ltrs. Ø Sump Tank : Capacity 70 Liters. Ø Stop Watch : Electronic Ø Control Panel : On/Off Switches, Main Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
Pilot Static Tube Set Up
DESCRIPTION:-
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper / SS is supplied and is fixed below Vernier scale. The Vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube Ø To plot velocity profile across the cross section of pipeUTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pitot Tube : Material Copper/SS of compatible size fitted with Vernier Scale Ø Test Section : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 40 Ltrs. Ø Sump Tank : Capacity 70 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
Bernoulli S Theorem Apparatus
DESCRIPTION:-
The Set-up is designed to verify Bernoulli’s Theorem experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli’s Theorem. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:-
Ø To verify Bernoulli’s Theorem experimentally.FEATURES:-
Ø Clear test section Ø Closed loop water circulation Ø Compact & stand alone setup Ø Stainless Steel tanks and wetted parts Ø Superb Painted structure Ø Simple to operate & maintainUTILITIES REQUIRED: –
Ø Electricity Supply: Provide 230 +/- 10 VAC, 50 Hz, Single Phase electric supply with proper earthing (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump Ø Water Supply : Tap water connection ½ “ BSP, Distilled water @ 60 Ltrs. (Optional)TECHNICAL SPECIFICATION: –
Ø Test Section : Material Acrylic, Size Ø Inlet Tank : Capacity 20 Liters., Stainless Steel Ø Supply Tank : Capacity 70 Liters., Stainless Steel Ø Measuring Tank : Capacity 20 Ltrs. Fitted with Piezometer Tube & Scale Ø Piezometer Tubes : Material P.U. Tubes (9 Nos.) Ø Pump : FHP Capacity make Tullu/Crompton Graves Ø Piping : GI / PVC Size BSP Ø Stop Watch : Electronic Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
Study Of Flow Measurement Devices
Measurement of liquid flow is required at various places and for various purposes. Different types of flow measuring devices are used depending upon the system conditions, accuracy required, skill of operator and economy desired. The unit demonstrates some of the flow measurement devices.
SPECIFICATIONS:
[1] Intergratiry Type Turbine flow meter. [2] Glass Tube Rotameter. [3] Orificemeter differential manometer. [4] Venturimeter [5] Measuring Tank [6] Stop Watch (Digital) [7] 112 HP Monoblock Pump. [8] A differential manometer. [9] Sump tank of suitable capacity. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC.Power Supply
Flow Over Weir Or Open Channel Apparatus
Flow Over Weir Or Open Channel Apparatus:
A ‘WEIR’ is the name given to concrete or masonry structure built across a river (or stream) in order to raise the level of water on the upstream side and to allow the excess water to flow over its entire length to the downstream side. Weirs may also be used for measuring the rate of flow of water in river or streams.
Different shapes of “WEIRS” generally used are sharp-crested weir, broadcasted weir and ogee shaped weir.
In the unit a centrifugal pump sucks the water from the sump tank, and discharges it to a small flow channel. The weir is fitted at the end of channel. All the weirs are interchangeable. The water-flowing over the weir falls in the collector. Water coming at from the collector can be directed to the sump or can be directed in to the measuring tank for measurement of flow.
Reviews
There are no reviews yet.