Description
[contact-form-7 404 "Not Found"]
Xilinx Spartan 3E FPGA Trainer Kit
Specification
• XC3S250E – 4PQ208C / XC3S500E-4PQ208C
• 16 Nos. of digital input using slide switches with LED indication
• 16Nos. Of digital outputs using discrete LEDs
• 16 x 2 LCD is provided for display the text message.
• One Reset Switch
• One switch is provided for giving manual clock
• FPGA configuration through
– JTAG Port
– On board Flash Prom XCF02S
• Total 158 I/O pins : 124 pins used for integrating peripherals like LED, Switches etc., balance pins available to user in 20 pin
• header (3.3V compatible)
• 1No of 26pin header to interface VLIM cards like Traffic Light Controller (5V compatible)
• On board programmable PLL oscillator from 1 MHz to 100 MHz using jumpers
• 4 Nos of 7 segment LED display
• One relay and Buzzer provided.
• Stepper & DC motor Driver provided.
• 4 * 4 matrix key provided
• Housed in a sleek plastic cabinet with built in SMPS 5V/2A.
• Compatible with Xilinx ISE Design Suite WebPACK Software.
• On board USB to JTAG is available for configure FPGA (Supports only with Vi JTAG 5.0 Software)
Related products
VHDL/VERILOG Learning Kit
Features
• Based on 64 Macro cell Xilinx CPLD device : XC2C64A • 20 SPDT Slide switches • 16 output LEDs and One 7 segment LED display • 4x4 Matrix keys using Micro switches (4 multiplexed with 4Nos of Slide switch) • One NC/NO switch for giving manual clock • Square wave Oscillator • Onboard USB to JTAG and External JTAG Connector for programming the CPLD • 16 I/O Lines terminated at 20 pin connecter. • External 5 volt 2Amp power supply • Compatible with Xilinx ISE Design Suite Web Pack Software. • USB Cable • Onboard USB to JTAG is Compatible only with Vi JTAG 5.0 Software.
Spartan 6 Trainer Kit
Features
• 16 Nos. of digital input using slide switches with LED indication • 16 Nos. of digital output using discrete LEDs • 16× 2 LCD is provided for display the text message. • One Reset Switch • One switch for giving manual clock • FPGA configuration through - On board Xilinx USB to JTAG Programmer with isolation to configure FPGA - On board Flash Prom XCF04S (Programmable through USB to JTAG programmer) • Total 186 I/O Pins: 100 Pins used for integrating peripheral like LED, Switches etc., balance pins are available to user • In 3nos of 20 pin header. • 1 No of 26 pin header to interface VLIM cards like Traffic Light Controller / On-board TLC (factory settable). • On board programmable PLL oscillator from1 MHz to 100MHz using jumpers • 4Nos of 7 segment LED display • One relay and Buzzer provided. • Stepper & DC motor drive provided on board (Motor Optional) • 4x4 matrix key provided • On board I2 C RTC Interface • On board Temperature Sensor Interface • SPI Based Analog to Digital Converter
Advanced Universal FPGA Trainer
The universal FPGA trainer consist of a main board with many peripheral like USB Device, Ethernet, Serial ports, Parallel Port, VGA port, Graphics LCD, Switches, LED, ADC etc. This motherboard has 4Nos of high speed connectors for plugging the daughter boards, which contains the FPGA of any manufacturers. Separately 2Nos of 100 pin high speed connectors provided for hardware expansion as plug in boards.
• Industry standard interconnection
- 10 MBPS Ethernet
- USB 2.0 Interface
- Two RS232 ports
- 9 pin D connector
• Memory Sub system
- 8 MB x 16 Bit SDRAM
- 4MB x 16 bit flash EEPROM
- 256KB I2C EEPROM
• Additional Features
- One 240 x 128 graphics LCD
- 16 Nos of dip switches
- 16 discrete LEDs
- 4 digit multiplexed 7 segment LED display
- 4 x 4 matrix keyboard
- One VGA Port at 15 pin D connector
- One PS2 connector for keyboard and mouse
- Reset Switch
- I2C Real time Clock
• Analog Input & Output
- 2MSPS SPI ADC (12 Channel)
- Temperature sensor interface
- One 16 bit Stereo CODEC
• 2 Nos. of 100 pin high speed connectors provided to hardware expansion can be used as hardware bus.
• Multilayer board for superior signal integrity.
• 54 I/O pins terminated at 3Nos of 20 pin connector for external interfacing.
Reviews
There are no reviews yet.