Submercible Pump Test Rig

DESCRIPTION:

The Set-up is designed to study the performance of Reciprocating Pump. The Set-up consists of a Reciprocating Pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop water circulation. Pressure and Vacuum Gauge are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.

EXPERIMENT:

To determine overall efficiency and pump efficiency of the Reciprocating Pump To plot Head vs. Discharge, Pump efficiency vs. Discharge

FEATURES:

Closed loop water circulation Compact & stand alone set-up MS Excel sample calculation program on demand Stainless Steel tanks and wetted parts Superb painted structure Simple to Operate & Maintain

UTILITIES REQUIRED:

Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½” BSP., Distilled water @ 80 Ltrs. (Optional extra cost)

TECHNICALS SPECIFICATIONS:

Pump : Double acting, single Cylinder, Capacity 1 HP Speed 250 RPM (max.), Head 5 Kg/cm2 (max.) Drive : AC Motor with step cone pulley arrangement for 3 prefixed speed Or DC Motor with DC Drive along with non-contact type Digital RPM Indicator Supply Tank : Capacity 70 Ltrs. Measuring Tank : Capacity 50 Ltrs. fitted with Piezometer Tube & Scale Piping : GI / PVC Stop Watch : Electronic Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structure.

DESCRIPTION:

The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.

EXPERIMENT:

Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAM

FEATURES:

Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & Maintain

UTILITIES REQUIRED:

Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)

TECHNICAL SPECIFICATIONS:

Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.

DESCRIPTION:

Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.

EXPERIMENT:

1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine Efficiency

UTILITIES REQUIRED:

● Water Supply and Drain.
● Electricity 15 kW, 440V AC, Three Phase

TECHNICAL SPECIFICATIONS:

MODEL	HM 111 (1.33 HP)	HM 111 (2 HP)	HM 111 (5 HP)
Output Power	1.33 HP / 1 Kw	2 HP / 1.5 Kw	5 HP / 3.75 Kw
Discharge	300 LPM (Approx.)	400 LPM (Approx.)	630 LPM (Approx.)
Supply Head	25 m	40 m	45 m
Rope Brake Dynamometer	Dia 200 mm	Dia 200 mm	Dia 300 mm
Sump Tank	Capacity 150 Liters.	Capacity 200 Liters.	Capacity 300 Liters.
Water Circulation Centrifugal Pump	Capacity 5 HP, Three Phase	Capacity 7.5 HP, Three Phase	Capacity 15 HP, Three Phase
Speed	1000 RPM (approx.)
Impeller	Material Brass, Bucket type
Nozzle	Material Stainless Steel/Mild Steel
Spear	Material Stainless Steel/Mild Steel
Discharge Measurement	Pitot Tube with Manometer
Control Panel	Star/Delta Starter, Mains Indicator, MCB for overload protection
The whole set-up is well designed and arranged in a good quality painted structure.

DESCRIPTION:

Francis Turbine is a reaction Turbine, which was developed by English born American Engineer Sir J.B. Francis. The water enters the turbine through the outer periphery of the runner in the radial direction and leaves the runner in axial direction and hence it is called a mixed flow turbine. As the water flows to the runner, a part of pressure energy goes on changing into kinetic energy. Thus the water through the runner is under pressure. The runner is completely enclosed in an air tight casing and the casing & runner is always full of water. The present Set-up consists of a runner. The water is fed to the turbine by Means of centrifugal Pump, radially to the runner. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is provided with a transparent. The circular window of the turbine casing is provided with a transparent acrylic sheet for observation of flow on to the runner. The runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of brake arrangement so that the efficiency of the turbine can be calculated. A draught tube is fitted on the outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and vacuum Gauge are fitted at the Inlet and Outlet of the turbine to measure the total supply head on the turbine.

UTILITIES REQUIRED:

● Water Supply and Drain.
● Electricity 15 kW, 440V Ac, Three Phase

TECHNICAL SPECIFICATIONS:

MODEL	HM 101 (1.33 HP)	HM 101 (2 HP)	HM 101 (5 HP)
Output Power	1.33 HP / 1 Kw	2 HP / 1 Kw	5 HP / 3.75 Kw
Discharge	1000 LPM (Approx.)	1000 LPM (Approx.)	2000 LPM (Approx.)
Supply Head	10 m	10 m	15 m
Rope Brake Dynamometer	Dia 200 mm	Dia 200 mm	Dia 300 mm
Sump Tank	Capacity 300 Ltrs.	Capacity 300 Ltrs.	Capacity 600 Ltrs.
Water Circulation Centrifugal Pump	Capacity 5 HP, Three Phase	Capacity 5 HP, Three Phase	Capacity 15 HP, Three Phase
Speed	1500 RPM (approx.)
Runner	Having Curved Vanes
Discharge Measurement	Pitot Tube with Manometer
Control Panel	Star/Delta Starter, Mains Indicator, MCB for overload protection
The whole set-up is well designed and arranged in a good quality painted structure.