Description
[contact-form-7 404 "Not Found"]
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.
| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle.
Internal illumination with 3 fluorescent tubes.
Digital temp. Indicator-cum-Controller.
Related products
Disintegration Test Unit
Features
Digital timer with 1 second resolution. Accurate time out provided by microprocessor based time totalizer. Baskets move Up & Down as per IP/USP test specifications. Temperature Controlled by sensitive thermostats. Digital Tablet Disintegration Apparatus is designed for accurate estimation of disintegration time of tablets as per IP/USP standards. The instrument is designed to test to batches of six tablets, simultaneously. The unit consists of two beakers having capacity of 1000 cc each. In these beakers, suitable disintegration media can be taken. These can be temperature controlled using a in-built heater and a highly thermostat fitted inside the instrument. Microprocessor based time to talizer is provided for accurate time readout.Specifications
System :Digital Tablet Disintegration Apparatus. Up and Down Speed:30 rpm ± 2 rpm. Accuracy: 2% Resolution:1 sec. Operating Temp. Range:0 - 100°C Power:230V ± 10%, 50Hz.AC
Hot Air Oven
| Specification | : | Hot air oven, 2 shelves |
|---|---|---|
| Technical Specifications | : | |
| Inside Body | : | Stainless Steel |
| Out Side Body | : | MS Powder coated with stove enamel paint. (SS body also available) |
| Number of Selves | : | 2 Adjustable Perforated Selves. |
| Body Structure | : | Double Walled structure filled with glass wool insulation |
| Number of Heaters | : | 2 x 1000 Watts |
| Heater Quality | : | High Quality Chrome Heater insulated with ceramic beads |
| Air Circulation | : | By Air Circulating Fan to ensure even temperature distribution. |
| Ventilation | : | Ventilation port with adjustable Opening. |
| Temperature Control | : | By Digital Temperature indicator and Controller |
| Temperature Display | : | Digital Temp. display |
| Range of Temperature | : | Ambient to 250ºC |
| Accuracy | : | 0.10C |
| Least Count | : | 1.0C |
| Power | : | 220 Volt AC 50 Hz. Single Phase |
| Sizes available are | : | 12" x 12" x 12" (28 Ltr.)14" x 14" x 14" (45 Ltr.)18" x 18" x 18" (95 Ltr.)24" x 24" x 24" (224 Ltr.) |
Autoclaves Pressure Steam Sterilizers Economy
Specification
These autoclaves are made of 10 gauge aluminum. The drum is deep drawn & the ring on top is riveted. The lid is made by casting. Locking of lid by 6 nuts with rubber gasket seal in between (not metal to metal seal). Two safety valves, pressure gauge, flexible metal rubbing to exhaust air. Includes outer stand, inner aluminum container, inner tripod stand.| Capacity (Lt.) | Power | Size | |
|---|---|---|---|
| 20 Lt. | Electric | 300 x 300mm = 12” x 12” | |
| 20 Lt. | Non Electric | 300 x 300mm = 12” x 12” | |
| 25 Lt. | Electric | 300 x 380mm = 12” x 15” | |
| 25 Lt. | Non Electric | 300 x 380mm = 12” x 15” | |
| 35 Lt. | Electric | 350 x 380mm = 14"x15" | |
| 35 Lt. | Non Electric | 350 x 380mm = 14"x15" |
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Laminar Air Flow
Product Details
| Material | : | STAINLESS STEEL |
| Model | : | Horizontal |
| Switches | : | Processor based switches for blower, LED light & UV light With LCD back light display. (UV light with Timer) |
| Pre-filter | : | 99.00% down to 5 micron. |
| HEPA Filter | : | 99.97%-99.99% down to 0.3 micron, Mesh guard for protection. |
| Airflow | : | Frontward Horizontally |
| Noise Level | : | 60 decibel ± 5%. |
| Velocity | : | 0.35-0.50m/sec. |
| Work Table | : | Made up of stainless steel 304gr. Cock for gas on work table. |
| Side Panels | : | 6mm±.5mm thick acrylic sheet. |
| Front door | : | Made of acrylic. |
| UV Lamp | : | 15/30W, make Philips Holland, |
| Illumination | : | LED White Light. |
| Pressure | : | Digital Manometer 0-50mm range with filter failure alarm. |
| Power Supply | : | 230V ± 10V/50 Hz single phase A.C. |
| Cabinet | : | 304 grade. Stainless Steel. |
| Heavy Duty Blower | : | Dynamically balanced with 0.25 HP Electric Motor Mounted on anti vibration pad 1440 RPM motor. |
Working Area Size
60x60x60cm. 90x60x60cm. 120x60x60cm. 180x60x60cm.
Blood Collection Vials (VACUTAINER) Plain/EDTA
Blood collection and storage is done is special tubes which allow the preservation of the blood sample over long periods.
These tubes can be made of glass or plastic and the caps of these vials are coloured to indicate the additives in them.
Some of the additives are anticoagulants such as EDTA, sodium citrate or heparin.
Other substances include preservatives. The containers containing coagulants are capped with gold, red or orange caps.
The ones containing anti-coagulants are green, which contain heparin, purple or lavender indicates ones which contain EDTA, grey capped tubes contain sodium fluoride or oxalate. Blood collection tubes (also called as vacutainers) are extensively used in hospitals, medical centres and diagnostic centres.
In biological labs, it is used in experiments like haemolysis etc.
Non Vacuum Vials (Pk of 100)
Vacuum Vials (Pk of 100)
Permeability Cup
(S.S 304) 120mm Dia. Permeability cups for determining the water-vapor transmission of paints, varnishes, coatings, coating systems and related products.
The Permeability cup consists of a cup, seal ring and cover ring.
The seal ring is designed to prevent turning when closing the cover.
The Permeability cup is suitable for testing both self-supporting coating and non-self-supporting coatings. Water-vapor transmission is of interest for high humidity conditions.
The wet cup method is thus the reference method for determining water-vapor transmission, if agreed up on otherwise, other procedures or conditions the dry cup method may be used.
Reviews
There are no reviews yet.