Description
Error: Contact form not found.
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.
| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle.
Internal illumination with 3 fluorescent tubes.
Digital temp. Indicator-cum-Controller.
Related products
Sterility Test Apparatus (S.S Manifold)
It consists of Stainless steel holders in the manifold of 3 of 6 to hold 47 mm dia membrane filters, the tops of the holders are connected to the outlets of flushing tube with silicone tubing and glass top cock.
A vacuum resistant flask or wolf bottle must be placed between the manifold and vacuum pump.
(Supplied without wolf bottle and vacuum/pressure pump).
These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media.
Filtration area is 12.5 cm and has a holding capacity of 250ml.
Though the only vacuum is required for filtration, some pressure is required for flushing liquids.
SPECIFICATIONS
| Material: | Stainless Steel | |
| Branch Test: | 3 Dia. 47mm | |
| Filtration Area: | 12.5 cm | |
| Holding Capacity: | 250 ml |
FEATURES
Robust design. Easy to use. Rustproof.APPLICATION
For microbiology, biochemistry, hydrobiology (DNA/RNA). Beverage analysis & food testing. Protein binding, gravimetric analysis, coliform, yeast, mould total bacteria & sterility testing. Ideal for water & wastewater analysis. Residue precipitate analysis and contamination tests. General Liquid Filtration.Single Test (Filter Holder S.S) Three Test
Horizontal Laminar Air Flow
Specifications
We deal in of horizontal laminar air flow that finds it applications in various hospitals, electronic industry and others. We use high grade component and quality raw material that is tested on various quality parameters and ensure smooth functionality. Direction of flow: Horizontal. Cleanliness: CLASS 100. Velocity: 90 FPM + / -20%. Hepa Filter: Size and QTY. will depend on the Size selected. Particle retention: Above 0. 3 micron. Blower Assembly: 1 / 3 HP, 1440 RPM. Noise level: 65 decibel + / -5%. Rate of air flow: 0. 40 to 0. 75 M / Sec. (90 FPM). Vibration level: < 2. 5 micron.Sizes mm.
60x60x60 90x60x60 120x60x60
Permeability Cup
(S.S 304) 120mm Dia. Permeability cups for determining the water-vapor transmission of paints, varnishes, coatings, coating systems and related products.
The Permeability cup consists of a cup, seal ring and cover ring.
The seal ring is designed to prevent turning when closing the cover.
The Permeability cup is suitable for testing both self-supporting coating and non-self-supporting coatings. Water-vapor transmission is of interest for high humidity conditions.
The wet cup method is thus the reference method for determining water-vapor transmission, if agreed up on otherwise, other procedures or conditions the dry cup method may be used.
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Distillation Plant (Manasty Type), Wall Hanging
The unit is recommended for making pyrogen fee distilled water of a very high degree of purity, Made out of S.S. special kettle element is fitted with Ejection Device / Auto cut for safety of the element is provided water supply is stopped.
The cork fitted to the unit is of brass C.P.A. wall Mounting clamp is provided with the unit.
Supplied with cord and plug to work on 220/240 volts A.C. Stainless Steel, Output approx. 3/4 Ltr./Hr.
Stainless Steel, Output approx. 5/6 Ltr./Hr.
Aluminium Dicasted, Output approx. 3/4 Ltr./Hr.
Aluminium Dicasted, Output approx. 5/6 Ltr./Hr.
Leak Test Apparatus (S.S BODY)
Ideal instrument to check blister Packs, Strip for Leak Test.
The old method of separate desiccator and the huge vacuum pump is replaced with the new Leak Test Apparatus in GMP Stainless Steel Body with phenomenal compactness.
The instrument is equipped with Diaphragm type vacuum pump gives the higher level of vacuum in shortest possible time.
Die pressed polycarbonate vacuum desiccator sustains vacuum for a long time.
A vacuum gauge is provided to indicate vacuum level which is connected to isolation valve to disconnect the source.
Thus avoiding the need of continues running of the vacuum pump.
| Body: | Stainless steel. 304 | |
| Desiccator: | SPolycarbonate, 8” Desicator Provided with Digital Timer | |
| Timer: | S3999 sec. Digital | |
| Vacuum Level: | S 22" Hg | |
| Current: | S 5A | |
| Voltage: | S 230 |
Reviews
There are no reviews yet.