Description
Error: Contact form not found.
Emissivity Measurement Apparatus
The apparatus consists of a test plate and a comparator. A black plate is used as a comparator for test plate. When all the physical, dimensions and the temperatures are equal, heat losses from both plates will also be the same, except radiation losses. Hence the input difference will be due to difference in emissive. Both the plates are kept in a panel enclose with perplex front and are given inputs through separate dimmerstats so that temperatures of both can be kept equal. Thus emissivity can determine over a wide range of temperatures.
SPECIFICATIONS:
1.Test plate and Black plates — 160mm. Dia. Aluminum plates, mounted in Panel with mica heater inside.
2.Instrumental panel consisting of-
a)Voltmeter and ammeter for input measurement to both heaters through a selector switch.
b)Separate dimmers for both the plates.
c)Multichannel digital temperature indicator.
A technical manual accompanies the unit.
SERVICES REQUIRED:
1.Space area of 1.5m x 1 m. at working height.
2.230v, 15A, AC supply with earthing connection
Related products
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
Natural Convection Apparatus
The unit consists of a vertical brass pipe heated by a cartridge heater inside it. The pipe looses heat to atmosphere by natural convection. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter. Thus students can determine overall heat transfer coefficient and local transfer coefficients in natural convection at various heat transfer rates.
SPECIFICATIONS:
1.Pipe – Brass pipe, 38mm. dia. (OD) 500mm. long, fitted with cartridge heater inside. 2.Thermocouples are fitted along with the length of pipe for Temperature measurement – 7 nos. 3.Enclosure 200mm. x 200mm. x 800mm. size, with one side of Perspex sheet. 4.Measurements & Controls a) A Dimmerstat for heater input control. b) Voltmeter and Ammeter for heater input measurement. c) Multichannel digital temperature indicator. A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of 1.5m x 0,75m. at working height. 2.230v, 5A, AC, electric supply with earthing connection.
Thermocouple Calibration Test Rig
The Unit helps in calibrating given thermocouple for the range 0°C to 100°C. While calibrating, thermocouple is once dipped in ice for 0Q C and then in boiling water for 100°C. This is done till the thermocouple shows the actual temperature of ice (0° C) and boiling wafer (100°C) and a linear calibration is set. A mV meter is provided to know the corresponding voltage.
SPECIFICATIONS:
1.A digital mV Meter and a digital temperature indicator with 2 different type of thermocouples. 2.A water container with heater of 1 KW. 3.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Table surface area – 2 m X 1 m X 0.5 m height. 2.220V, 50hz. Stabilize Electric Power Supply. 3.Ice cubes – 0.5Kg. Approx.
Theramal Conductivity Of Insulating Slabs
The apparatus consists of a slab assembly. The main Heater and a radial guard heater are sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other Sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates. By knowing the temperatures and Heat input, thermal conductivity of specimen can be calculated. The test set up is enclosed in an enclosure with insulation inside to provide undisturbed Surroundings. The design style of the apparatus is similar to as recommended in INDIAN standard. The difference is in sizes.
SPECIFICATIONS:
1.Heaters: a)Main heater plate 110 mm dia. with mica heater Sandwiched between copper plates. b)Radial guard heater plate I.D. 120mm and OD 200 mm mica heater sandwiched between copper plates. 2.Water circulated cooling plates -2 nos. 3.Dimmerstat-2 A capacity – 2 nos. to independently control Inputs to the heaters. 4.Measurements – A voltmeter and an Ammeter with selector switches to measure inputs,Multichannel digital temperature indicator to measure Temperatures at various points, having 0.1 °c least count. A technical manual accompanies the unit.SERVICES REQUIRED:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Water supply of about 4-5 lit/min. 3.Bench area 1m x lm x O.5m height.
Thermal Conductivity Of Liquid
Thermal conductivity of is an important engineering property. The apparatus uses guarded hot plate method for determining thermal conductivity. It consists of hot plate i.e. an electrical heater sandwiched between two plates. The heat loss from hot plate is prevented by using two guard heaters and heat of removes heat from liquid by circulation of water. Input to heaters the temperatures.
SPECIFICATIONS:
1.Guarded hot plate assembly comprising of main heater, ring guard heater and top guard heater, mounted over the liquid test cavity. 2.Cold plate assembly provided with water connections. 3.The assembly is housed in an enclosure box with glass wool insulation. 4.Instruments panel consisting of : a).Digital voltmeter and ammeter of suitable range. b).Dimmerstat for controlling input to the heaters (2 amp. 3 Nos.) c).Multichannel digital temperature indicator.SERVICES REQUIRED:
1.Floor space of about 0.75m. x 1.5m. at working height. 2.230v. AC electrical supply with earthling connection. 3.Water flow rate of about 10- 15 lit/min. at constant head.
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes : a)Gl pipe (innermost) – 6 cm. (Outer Diameter). b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter) c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter) d)Length of pipes 1 Meter. 2.Heater : Nichrome wire cartridge heater placed centrally, of suitable capacity. 3.Control Panel : a)Single Phase Dimmerstat – 1 No. b)Voltmeter (0 – 250V) – 1 No. c)Ammeter (0- 2A) – 1 No. 4.Temperature Indicator : Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI ThermocouplesServices Required:
1. A.C. Single Phase 230 V electric supply 2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Critical Heat Flux Apparatus
The apparatus demonstrates the regimes of pool boiling. The test section consists of a test wire surrounded by water of constant temperature. The surface temperature of the test wire is heated by passing current through it. Due to the temperature difference between the wire surface and surroundings, the difference regimes are observed till the burnout point.
Specifications:
1.Test wire -35 gauge or 40 gauges. Length = 10cm. 2.Nichrome heater- 1 kw capacity – 1 nos. 3.Glass trough of sufficient capacity. 4.Table light to observe the test wire. 5.Voltmeter and ammeter to measure the input to the test wire. 6.Dimmerstat to adjust the voltage. A technical manual accompanies the unit.SERVICES REQUIRED:
1.220v, ISA, stabilized single-phase supply. 2.Floor surface- 1m x 1m at working height.
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
Reviews
There are no reviews yet.