Description
Error: Contact form not found.
Generation Of Involute Gear Tooth Profile
This board illustrates the process of cutting of involutes Gear Teeth, by use of rack type cutter It consists of 3 white acrylic discs A, B, C. having pitch circle diameter 450 mm, 300 mm & 200 mm respectively. A gear tooth profile with module 25mm can be traced out on a peace of paper placed between disc and cutter. An affect of Interference and Undercutting on correct profile of gear tooth can be studied from the profiles traced.
Related products
Motorised Gyroscope Apparatus
The apparatus consists of a rotor mounted in bearings. This rotor is free to rotate about
(i) Its own axis i.e. axis of spin.
(ii) Axis of precession.
(iii) Axis of gyroscopic couple.
The rotor is connected to the variable speed motor. The weight of the motor is balanced by another weight, which is on either side of the rotor. By putting weights on the weight platform torque can be supplied to rotor, which is also called gyroscopic couple.
SPECIFICATIONS OF MOTORISED GYROSCOPE APPARATUS:
1.Rotor dia. 250mm free about 3 axis of rotation driven by variable speed motor. 2.Dimmerstat to control the motor speed. 3.Stopwatch to measure the angular speed about the axis of precession. 4.Weights – 0.2 kg, 0.5 kg and 1 kg. 5.A technical manual accompanies the unit.SERVICES REQUIRE FOR MOTORISED GYROSCOPE APPARATUS:
1.220v stabilized AC supply with earthing connection. 2.Bench area – 0.5 x 0.5m at working height. 3.Tachometer for speed measurement (can be supplied at extra cost).
Journal Bearing Apparatus
DESCRIPTION:
The apparatus consists of a plain steel shaft encased in a bearing and directly driven by a small electric motor. The bearing is freely supported on the shaft and sealed at motor end. The motor speed is precisely controlled by control unit and sealed at motor end. The motor speed is precisely controlled by control unit and can be run in both directions. The bearing contains twelve equi-spaced pressures tapping around circumference and four along the axis. All are connected by light flexible plastic tube to the manometer so that the pressure head of all sixteen point can be observed at a time. The bearing can be loaded by attaching weight to the arm supported beneath it.SPECIFICATIONS:
1. Journal : 50 mm. dia. (nominal) 2. Bearing : 55 mm. dia. 3. Weights : 4 adjustable weights 4. Motor : D.C. shunt Motor, 3,000 RPM. 5. Control panel : For speed control of Motor 6. Manometer panel : 16 tube Manometer 7. Oil recommended : SAE 10EXPERIMENTS:
1. Observation of the pressure profile at various conditions of load and speed. 2. Plotting the Cartesian and polar pressure curves. 3. Plotting the theoretical Summerfield curves.SERVICE REQUIRED:
1. Electric Connections : A.C Single Phase, 230v. supply with ear thing. 2. Stand Alone Space : 1.5m X 1.5m X 4m Height.
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
SPECIFICATIONS OF CAM ANALYSIS APPARATUS:
1.Cam -Eccentric, tangent and circular ARC type – one each. 2.Follower- mushroom, flat faced and roller type – one each. 3.Cams and followers are hardened to reduce wear of the surfaces. 4.Variable speed motor coupled to camshaft of suitable range and Variac. 5.A dial gauge to note the follower displacement. 6.A technical manual accompanies the equipment.SERVICES REQUIRE FOR CAM ANALYSIS APPARATUS:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)
Motorised Governor Apparatus
The unit consists of a base upon which the bearing holders and driving motor are bearing can be fitted in a holders to end conditions for test shafts, viz. Both end fixed and one end free, one end fixed. A Variac provided control of driving motor. The unit demonstrates the phenomenon of whirling of shafts with single rotor. As the test is destructive, after the test cannot be used, hence the unit only demonstrates the principle.
However, results obtained are closer to theory, as compared to those with bare shafts. Also, It can be demonstrated that, after passing whirling speed, shaft again starts running true.
SPECIFICATIONS OF MOTORISED GOVERNOR APPARATUS:
1.Test shaft – 4.75 mm, 6.35 mm and 7.9 mm – 2 each. 2.Bearing to provided end conditions, (a) Both ends fixed, (b) One end fixed and one end free. 3.Drive motor 1/8 HP, 1500 rpm with control arrangement. 4.The whole unit is mounted on a sturdy base. 5.Rotor for each shaft of suitable size. 6.A technical manual accompanies the unit.SERVICES REQUIRE FOR MOTORISED GOVERNOR APPARATUS:
Floor space area of 2m. X 1m. at working height. 230V, 15 A, AC electric supply connection.
Whirling Of Shaft Apparatus
The unit consists of a main spindle driven by a variable speed motor. Three different governor assemblies can be mounted over the spindle. A with pointer measures the lift of the governor. Students can calculate characteristics of governor at and compare their performance viz. Sensitiveness, stability, governor effort etc.
SPECIFICATIONS OF WHIRLING OF SHAFT APPARATUS:
1.Governor assemblies – Hartnell, porter & propel governor assembly one each with rotating weights. 2.Variable speed FHP D.C. motor to drive the main spindle. 3.Sliding weights for porter & proell governor. 4.Scale & a pointer to measure governor lift. 5.Spring & Spring compression adjustment arrangement. 6.A technical manual accompanies the unit.SERVICES REQUIRE FOR WHIRLING OF SHAFT APPARATUS:
1.230V, 5A, AC supply connection. 2.Bench area of 0. 75 x 1m. at working height.
Drilling Tool Dynamometers
This is a armed wheel type strain gauge drill tool dynamometer designed to measure thrust and torque during drilling operation. This Dynamometer is suitable for drilling a hole up to 25mm size in mild steel. With this Dynamometer students can study the change in these force by varying speed, cut and feed
FEATURES:
1.Rigid in construction & Sensitive transuding and amplifying system for accuracy in force measurement. 2.Compact two channel digital force indicator. 3.Use of cutting fluid during operation is possibleSCOPE OF SUPPLY:
1.Mechanical sensing unit and work piece holder with strain gauges. 2.Control panel housing digital force indicator to measure both forces simultaneously, balancing potentiometer, connoting cables. 3.Necessary switches, fuses and screen printed front plate. 4.The dynamometer is calibrated at factory with help of proving ring and readings are directly in the from of kg.
Dead Weight Pressure Gauge Tester
DESCRIPTION:-
Dead weight Pressure Gauge Tester is manufactured to measure the Pressure gauge up to the capacity of 25kg/cm2.The system is nickled chrome to protect from rust. The weights are Zink Iron for long term use.EXPERIMENTS:-
• Study of the hydrostatic force on a plane surface under different submerged conditionsFEATURES:-
• Superb Painted structure • Simple to operate & maintainUTILITIES REQUIRED:-
• Machine Oil.SPECIFICATION:-
• Bourdon tube pressure gauge as manometer • Manometer with transparent scale • Manufactured from corrosion resistant materials • Components arranged on base plate. • Set of weights • Medium for transmitting pressure: hydraulic
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
Reviews
There are no reviews yet.