Description
Error: Contact form not found.
Oscilloscope
This is a portable type of Oscilloscope for two traces. The band width is 0-20 MHz. The instrument is of easy operation with comfortable controls. Its reasonable structure and technology makes it convenient to repair and calibrate.
(1) Dual Trace Dual Channel Oscilloscope with Component Test Facility
(2) Bandwidth : 20 MHz
(3) Full bandwidth sweeping circuit is used in the sweeping system
(4) The flexible and convenient triggering mode has the functions for selecting signals from one channel or triggered by Ext signals
(5) ALT trigger to observe signals from two irrelative channels
(6) The instrument has the functions of TV-H / TV-V synchronization and trigger-lock to observe all kinds of signals stably
(7) From the terminal for trigger input, CH1 and CH2 signals can be output along with the triggering channel to connect the external frequency counter
(8) Y deflection operation : Y1, Y2, ALT, CHOP, ADD, mode X-Y
(9) Vertical Deflection : 5 mV / Div to 20 V / Div in factor 1-2-5 sequence in 12 steps
(10) Rising time : < 18 nS (11) Maximum Input Voltage : 400V (DC + ACp-p) (12) Triggering Source : Y1, Y2, ALT, POWER, EXT (13) Trigger Coupling : AC / DC (EXT), NORM / TV-H, TV-V (14) Horizontal Sweep Mode : AUTO, TRIG, LOCK, SINGLE (15) Sweep time factor : 0.1 uS / div to 0.2 s / div in 1-2-5 sequence in 20 steps (16) Magnification : x10 (17) X-Y Mode input : X-Axis Y1 and Y-Axis Y2 (18) Z Axis minimum input level : TTL Level (19) Component Test Facility (20) Calibration Signal : Square wave of 0.5 V at 1 kHz (21) CTR Display size : 8 cm x 10 cm (22) Auxiliary Power Supply : 220V 50Hz AC
Related products
Bridge Rectifier
Bridge Rectifier is made of four diodes connected in a bridge circuit. It is housed in a plastic moulded box. This bridge rectifier converts alternating current (AC) into direct current (DC). It provides the same output polarity for either input polarity. All the electronic devices require direct current, so bridge rectifiers are used inside the power supplies of almost all electronic equipment. For the easy understanding of the internal circuitry, the circuit diagram is printed on the box.
Logic Gates Trainer
Logic Gates Trainer has been designed to study logic gates and applications. This trainer board is designed to verify the truth table of various logic functions, to prove De-Morgan’s theorem, Half adder and Full adder by using logic gates. The board is absolutely self-contained and requires no additional apparatus. 12 V / 1 A DC adaptor is required to operate it.
Instrumentation Amplifier
Instrumentation amplifier is a switched gain precision operation amplifier. This is used for precise and accurate, low noise differential signal acquisition. 4mm sockets are used for the input signal. It can be interfaced with a wide range of sensors. It can take small voltage changes from a sensor and make those changes large enough to be measured using CRO. It is not able to drive a low impedance load such as a loudspeaker or relay. The output can be read on CRO. Digital multimeter may also be used to read the output. With switched gain of 5 to 1000, it can handle signal inputs over a very wide range making it suitable for almost all applications.
Digital / Analog Training System
Solderless Breadboard has 1680 tie points. Provided with 2 Terminal strips and 4 Distribution strips. Built in DC Regulated Power Supply. DC Supply ± 5V/ 1 Amp. 0 to ± 15V DC (Variable), 1 Amp. Built-in Function Generator. . Waveform : Sine, Square and Triangle (with selector switch),
Frequency : 1 – 100 Hz Variable
Amplitude : Variable up to 10 V, TTL 5V p-p
Data Switches (Bounceless) – 8 No.
LED Display (buffered) – 10 No.
Clock Pulsar – 2 No.
Seven Segment Display with Decoder IC 7447 – 2 No.
Speaker 2.5” Dia. with sockets – 1 No.
BNC Plug with 2 mm Sockets – 2 No.
4 mm socket connected with 2 mm sockets – 2 No.
Interconnection leads having 2 mm plugs at one end – 10 No.
Interconnection leads having 4 mm plugs at both end – 10 No.
22 SWG Hook Up Wire of 20 cm length – 100 No.
Comprehensive User’s Manual – 1 No.
Input 220 V, 50 Hz. AC with On/Off indicator.
LCR Resonance Apparatus
Objective : To plot Frequency Vs. Current Characteristics of LCR circuit when connected in series or in parallel.
Features : Instrument comprises of 3 Resistances, 3 Capacitors and 1 Inductance connected inside and connections brought out at Sockets. 2 AC moving coil meters to measure voltage and current.
Optional Acc. : Audio Frequency Function Generator
Reviews
There are no reviews yet.