pH, Conductivity and Temperature Meter, Digital, Table Model

Specification

BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.

Inner Chamber Size	Cap.	Material
455 x 410 x 610 mm	4cu. Ft. or 112 Ltr.	Aluminium
455 x 410 x 610 mm	4cu. Ft. or 112 Ltr.	S.S.
505 x 451 x 830 mm	6cu. Ft. or 171 Ltr.	Aluminium
505 x 451 x 830 mm	6cu. Ft. or 171 Ltr.	S.S.
565 x 565 x 865 mm	10cu. Ft. or 280 Ltr.	Aluminium
565 x 565 x 865 mm	10cu. Ft. or 280 Ltr.	S.S.

Optional

Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.

Features

Robust designing Sturdiness Low maintenance Light weight Low noise

Other information

Widely used in food, pharmaceutical, ceramics and national defense industry Provided with automatic shut down timer Used to analyze particle size and debris content

It consists of Stainless steel holders in the manifold of 3 of 6 to hold 47 mm dia membrane filters, the tops of the holders are connected to the outlets of flushing tube with silicone tubing and glass top cock. A vacuum resistant flask or wolf bottle must be placed between the manifold and vacuum pump. (Supplied without wolf bottle and vacuum/pressure pump). These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media. Filtration area is 12.5 cm and has a holding capacity of 250ml. Though the only vacuum is required for filtration, some pressure is required for flushing liquids.

SPECIFICATIONS

Material:	Stainless Steel
Branch Test:	3 Dia. 47mm
Filtration Area:	12.5 cm
Holding Capacity:	250 ml

FEATURES

Robust design. Easy to use. Rustproof.

APPLICATION

For microbiology, biochemistry, hydrobiology (DNA/RNA). Beverage analysis & food testing. Protein binding, gravimetric analysis, coliform, yeast, mould total bacteria & sterility testing. Ideal for water & wastewater analysis. Residue precipitate analysis and contamination tests. General Liquid Filtration.Single Test (Filter Holder S.S) Three Test

The unit is recommended for making pyrogen fee distilled water of a very high degree of purity, Made out of S.S. special kettle element is fitted with Ejection Device / Auto cut for safety of the element is provided water supply is stopped. The cork fitted to the unit is of brass C.P.A. wall Mounting clamp is provided with the unit. Supplied with cord and plug to work on 220/240 volts A.C. Stainless Steel, Output approx. 3/4 Ltr./Hr. Stainless Steel, Output approx. 5/6 Ltr./Hr. Aluminium Dicasted, Output approx. 3/4 Ltr./Hr. Aluminium Dicasted, Output approx. 5/6 Ltr./Hr.