pH Meter, Digital, Table Model

Specification

BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.

Inner Chamber Size	Cap.	Material
455 x 410 x 610 mm	4cu. Ft. or 112 Ltr.	Aluminium
455 x 410 x 610 mm	4cu. Ft. or 112 Ltr.	S.S.
505 x 451 x 830 mm	6cu. Ft. or 171 Ltr.	Aluminium
505 x 451 x 830 mm	6cu. Ft. or 171 Ltr.	S.S.
565 x 565 x 865 mm	10cu. Ft. or 280 Ltr.	Aluminium
565 x 565 x 865 mm	10cu. Ft. or 280 Ltr.	S.S.

Optional

Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.

Features

Robust designing Sturdiness Low maintenance Light weight Low noise

Other information

Widely used in food, pharmaceutical, ceramics and national defense industry Provided with automatic shut down timer Used to analyze particle size and debris content

It consists of Stainless steel holders in the manifold of 3 of 6 to hold 47 mm dia membrane filters, the tops of the holders are connected to the outlets of flushing tube with silicone tubing and glass top cock. A vacuum resistant flask or wolf bottle must be placed between the manifold and vacuum pump. (Supplied without wolf bottle and vacuum/pressure pump). These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media. Filtration area is 12.5 cm and has a holding capacity of 250ml. Though the only vacuum is required for filtration, some pressure is required for flushing liquids.

SPECIFICATIONS

Material:	Stainless Steel
Branch Test:	3 Dia. 47mm
Filtration Area:	12.5 cm
Holding Capacity:	250 ml

FEATURES

Robust design. Easy to use. Rustproof.

APPLICATION

For microbiology, biochemistry, hydrobiology (DNA/RNA). Beverage analysis & food testing. Protein binding, gravimetric analysis, coliform, yeast, mould total bacteria & sterility testing. Ideal for water & wastewater analysis. Residue precipitate analysis and contamination tests. General Liquid Filtration.Single Test (Filter Holder S.S) Three Test

Specification

These autoclaves are made of 10 gauge aluminum. The drum is deep drawn & the ring on top is riveted. The lid is made by casting. Locking of lid by 6 nuts with rubber gasket seal in between (not metal to metal seal). Two safety valves, pressure gauge, flexible metal rubbing to exhaust air. Includes outer stand, inner aluminum container, inner tripod stand.

Capacity (Lt.)	Power	Size
20 Lt.	Electric	300 x 300mm = 12” x 12”
20 Lt.	Non Electric	300 x 300mm = 12” x 12”
25 Lt.	Electric	300 x 380mm = 12” x 15”
25 Lt.	Non Electric	300 x 380mm = 12” x 15”
35 Lt.	Electric	350 x 380mm = 14"x15"
35 Lt.	Non Electric	350 x 380mm = 14"x15"