Description
Error: Contact form not found.
Resistance Box, Plug Pattern
Description
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops.
The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used.
Coils are non-inductively wound and are treated to be strain-free.
Coil values are engraved on the plate and an infinity plug is also included.
Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest
0.01 to 0.1 ohm, Total 0.2 ohm
0.1 to 1 ohm, Total 2 ohm
0.1 to 5 ohm, Total 11 ohm
0.1 to 10 ohm, Total 21 ohm
0.1 to 50 ohm, Total 111 ohm
0.1 to 100 ohm, Total 211 ohm
0.1 to 500 ohm, Total 1111 ohm
1 to 10 ohm, Total 20 ohm
1 to 50 ohm, Total 110 ohm
1 to 100 ohm, Total 210 ohm
1 to 500 ohm, Total 1110 ohm
1 to 1000 ohm, Total 2110 ohm
1 to 5000 ohm, Total 11110 ohm
Related products
DC Motor Kit
Description
A simple kit for students to gain insight into field poles, armatures and switches, one mounting base, two coils of insulated wire , field pole, mounting bracket, two armature halves, one piece of insulating tubing, motor shaft, two commutator insulators, two bronze wire brushes, two shaft supports, four paper fasteners, a AA battery holder and 6 each of screws and nuts. Requires one AA battery, not supplied, with assembly instructions.
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.
Westminister Electromagnetic Kit
Description
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.
Accessories Set For Demountable Transformer
Description
Comprising 1 welding coil of 5 turns on former with insulated handle and short-circuiting pins,1 annular melting trough with insulated handle to show heating by induction,1 jumping ring which is thrown clear when primary current is started and a floating ring which remains freely suspended when primary current is flowing.
Reviews
There are no reviews yet.