Description
Error: Contact form not found.
Resistance Demonstration Set
Description
Resistance Demonstration Set demonstrates the relation between resistance and cross section of different wires.
This set has 2 copper and 2 nichrome wires of different diameters.
A pair of colourcoded terminal used for power supply connection.
This set uses 6V DC to operate.
Related products
Demountable Transformer
Description
This heavy duty demountable transformer can be used for the study of transformertheory and many other alternating current phenomena. This kit consists of: 1. A magnetic circuit made of highly permeable U shape metal sheet, which can be closed using two clamps with tightening screws. 2. Section: 40 x 40 mm with 150 mm length and 170 mm height. 3. One coil of 6000 turns with maximum current of 0.2 A. Intermediary coil of 2000 turns output. 4. One coil of 600 turns with maximum current of 2.5 A, which is mainly used to create the primary of transformer. 5. One coil of 1200 turns with maximum current of 1.25 A, fitted with intermediary 400 and 800 turns outputs. 6. One coil of 72 turns with maximum current of 12 A, fitted with intermediary 6, 30, 54 and 66 turns outputs. 7. Power supply cable.
Motor Generator Model Set
Description
This motor-generator set gives students an insight into the physical and technical relationships on which electric motors, generators and transformers are based. The modular system allows to set up different function models without tools: Various DC motors Series and shunt motor Synchronous motor DC generator and alternator Transformer. This set allows the performance of 10 student experiments about the following topics: Magnetic field of a coil Conversion of electrical energy into kinetic energy Commutator Direct current motor Synchronous motor Series and shunt-wound motors Electromagnetic induction The electrical generator Engine-generator Transformer
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)
St. Louis Motor Demonstration
Description
Students can explore how a simple electric motor works by doing a series of investigations. This St. Louis motor can be adjusted so students can study the effect of voltage and position of the brushes on the commutator. The motor consists of a two pole DC armature. The brush holder, with two heavy binding post terminals, can be rotated for experiments. The permanent bar magnets, supported by clamps, can be adjusted to the desired location. This apparatus requires 4 D cell batteries with holder (not included) or a power supply and two connecting leads (not included).
Reviews
There are no reviews yet.