Description
Error: Contact form not found.
Water Bath Tissue Flotation
Specifications
Double walled round construction. Inner chamber stainless steel/black anodized aluminum and outer made out of mild steel painted in epoxy powder coating.
Thermostatic control, temperature range from ambient to 80°C. Complete with indicators, wire & plug. To work on 220V AC.
Chamber Size In mms (dia x depth)
200×75
250×125
Related products
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Sterility Test Apparatus (S.S Manifold)
It consists of Stainless steel holders in the manifold of 3 of 6 to hold 47 mm dia membrane filters, the tops of the holders are connected to the outlets of flushing tube with silicone tubing and glass top cock.
A vacuum resistant flask or wolf bottle must be placed between the manifold and vacuum pump.
(Supplied without wolf bottle and vacuum/pressure pump).
These units are used for sterility testing when the membranes filter is to be removed from the holder for incubation in culture media.
Filtration area is 12.5 cm and has a holding capacity of 250ml.
Though the only vacuum is required for filtration, some pressure is required for flushing liquids.
SPECIFICATIONS
| Material: | Stainless Steel | |
| Branch Test: | 3 Dia. 47mm | |
| Filtration Area: | 12.5 cm | |
| Holding Capacity: | 250 ml |
FEATURES
Robust design. Easy to use. Rustproof.APPLICATION
For microbiology, biochemistry, hydrobiology (DNA/RNA). Beverage analysis & food testing. Protein binding, gravimetric analysis, coliform, yeast, mould total bacteria & sterility testing. Ideal for water & wastewater analysis. Residue precipitate analysis and contamination tests. General Liquid Filtration.Single Test (Filter Holder S.S) Three Test
Blood Collection Vials (VACUTAINER) Plain/EDTA
Blood collection and storage is done is special tubes which allow the preservation of the blood sample over long periods.
These tubes can be made of glass or plastic and the caps of these vials are coloured to indicate the additives in them.
Some of the additives are anticoagulants such as EDTA, sodium citrate or heparin.
Other substances include preservatives. The containers containing coagulants are capped with gold, red or orange caps.
The ones containing anti-coagulants are green, which contain heparin, purple or lavender indicates ones which contain EDTA, grey capped tubes contain sodium fluoride or oxalate. Blood collection tubes (also called as vacutainers) are extensively used in hospitals, medical centres and diagnostic centres.
In biological labs, it is used in experiments like haemolysis etc.
Non Vacuum Vials (Pk of 100)
Vacuum Vials (Pk of 100)
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.
Orbital Shaking Incubator cum B.O.D
Specification
Orbital shaking incubator cum B.O.D incubator is specifically designed to controlled incubation with orbital shaking arrangement with powerful geared motor for many labotatory procedures such as tissue culture, fermentations studies, enzyme reactions, growth studies etc. The outer chamber is made up of M.S sheet duly powder coated & inner chamber is made of thick S.S. sheet. The gap between wall is fitted with high grade glass wool to avoid thermal loss. The plexi glass window provided to inspect the specimen without disturbing the inner temp. The incubator is illuminated with one door operated or panel operated flurescent tube. The unit has a temp. Range from 5°C to 60°C. The temperature is controlled by Dual Display Microprocessor PID Temperature Indicator cum Controller with a accurancy of + 0.5°C. Air circulation fan is provided to maintain stability throughout. The speed of shaker is variable from 30 RPM to 250 RPM. The tray of the shaker is also made of S.S sheet with lotus type clamps to hold flasks. The unit is fitted with Digital RPM meter, 999 min digital timer.Optional Accessories
Timer 0-24 Hours. Automatic voltage stabilizer 3KVA (Most rec.).Size
16 Flasks of 500ml. 25 Flasks of 250ml. 36 Flasks of 100ml.
Permeability Cup
(S.S 304) 120mm Dia. Permeability cups for determining the water-vapor transmission of paints, varnishes, coatings, coating systems and related products.
The Permeability cup consists of a cup, seal ring and cover ring.
The seal ring is designed to prevent turning when closing the cover.
The Permeability cup is suitable for testing both self-supporting coating and non-self-supporting coatings. Water-vapor transmission is of interest for high humidity conditions.
The wet cup method is thus the reference method for determining water-vapor transmission, if agreed up on otherwise, other procedures or conditions the dry cup method may be used.
Reviews
There are no reviews yet.