XTEMOS ELEMENT
AJAX PRODUCTS TABS
Test Tube Stand of 6 Holes, Wooden
Description
With vertical pins:
Wooden, polished stand with drilled holes, 2 of 25 mm dia. and 4 of 20 mm to accommodate 6 tubes with overall height of 9 cm and length of 20 cm. Vertical pins are provided for quick drying of the test tubes. Also available for 12 tubes, with 2 holes of 25 mm dia and 10 holes of 20 mm dia.Specifications :
Length : (in) 9.4 Width : (in) 3.5Without vertical pins and moulded supports:
Wooden with base and top with single row of 6 holes, clips together quickly and easily with two moulded supports. Height 11cm can accept two tubes of 30 mm and four tubes of 20mm diaSpecifications:
Length: (in)11.8 Width: (in)10.2Without vertical pins:
Wooden test tube stand - 6 holes of 22 mm dia. Test stand measures 9.5" long 2.5" wide base and 4.5" tall (Test tubes not included - shown for demostration )Specifications :
Weight: (lb)0.9 Length: (in)10.0
Interference Undercutting
The board shows the demonstration of this phenomenon of Interference and Undercutting. When we rotate the teeth in anticlockwise direction, as the teeth is undercut is gives us a smooth working. When we give a rotation in clockwise direction, we can observe that the rack tip will be resisted by the tooth flank thus giving interference.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Metabolic Cage for Rat
Description
Animal waste is directed through a collection funnel and onto a linear diffuser guide. The diffuser guide allows solid matter to travel down the top ridges of a 50% incline, passing over a urine port, and into a fecal collection vessel. Liquid waste flows along grooves down the inclined diffuser guide, passing through the urine port, and into a urine collection vessel. A urine deflector prevents excess urine from splashing and contaminating fecal specimen. Separate urine and feces samples are collected in two separate tubes.Features
Reliable experiment results due to better separation efficiency Food hopper design reducing the access or stay of animal inside food hopper Practicality of use due to less components or parts| Minimal animal stress: | Sample removing is without stressing animal, access to all elements below the cage floor without disturbing animal |
| Durability: | Most components are made from autoclavable polycarbonate and S.S. 304 material |
| Versatility: | Unit accommodates various species with simple feeder and floor change Space saving |
| Economy: Few parts, simple and rapid assembling |
Components Included
Polycarbonate cage with lid
Polycarbonate collection funnel
S.S. 304 floor grill for Mice and Rat
Polycarbonate Linear diffuser guide
Urine collection tube P.P.
Feces collection tube P.P.
Polycarbonate water bottle 250ml with holder
Waste water collection tube P.P.
Vibration Lab Complete 11 Experiment
The VIBLAB is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations.
This apparatus enables a comprehensive range of Vibration Experiments to be conducted on single basic framework. The frame is robustly constructed from channel section. The experiments are specially designed for quick and easy assembly on to the framework using a minimum amount of common engineering tools. To reduce changeover time on tube more advanced free and forced vibration experiments, large knurled knobs are used to clamp components on the frame and many components are common to several experiments.
All of the referenced groups of experiments are available separately making it possible to procure them individually & if required to build up a complete set over a period of time.
Specifications:
1.Wide range of experiments. 2.Forced and Free Vibrations. 3.Damped and undamped vibrations. 4.Arrangements for variation of damping. 5.Sturdy storage cabinet. 6.Experiments easily assembled. 7.Covers experiments for undergraduate studies. 8.Scope for student projects.Features:
[I] Pendulum Experiments: 1.Simple Pendulum. 2.Compound Pendulum. 3.Bi-filler Suspension. [II] Longitudinal Vibration Expiariment. 1.Spring Mass System. 2.Eciuivalent Spring Mass study of undarrped 3.System free vibration [III] Torsional Vibration Experiment. 1.Single Rotor Systern. 2.Two Rotor System. 3.Single Rotor with viscous darnping. [IV] Damped Vibration Experiment. 1.Verification of Dukerleys Rule. 2.Forced rotor with viscous damping along with frictional HP Motor Strip chart recorder & control unit. 3.A technical manual accompanies the equipment.Services required:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)
Synchromesh Gear Box 4 Forward 1reverse
Synchromesh Gear Box – 4 Forward & 1Reverse Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
V.D.R.L.Rotator (Variable Speed)
Suitable for VDRL and other agglutinating tests, blood grouping tests, for mixing of solutions in small flasks, beakers or bottles.
Platform size 300x300 mm. supplied with spring wire holder (2 nos) for holding flasks. Fixed or variable RPM range 180 RPM. with 60 min timer.
Workable on 220 v AC 50Hz single phase.
Optional
Digital R.P.M. indicator Digital timer (0-99 min.)
Front Suspension System
In this model the working of front suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a front suspension system are shown in actual working form. This model helps the student to understand the working of the front suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Macpherson Type Suspension System
(B) Double Wishbone Type Suspension System
(C) Longitudinal Torsion Bar Type Suspension System
Vacuum Laboratory Desiccator
We provide impressive range of Vacuum Laboratory Desiccator.
Made of Polypropylene and Polycarbonate, these autoclavable vacuum desiccators can hold Vacuum upto 740 mm of Hg for 24 hrs.
The top dome, molded in rigid and transparent Polycarbonate, gives a crystal clear view of the desiccant placed inside.
The Knurled knob on the top provides easy handling of the dome.
The lower part is made of Polypropylene. An internal groove is provided on the flange to hold a silicon rubber O-ring.
The Polypropylene stopcock is fitted with a self lubricating PTFE plug.
This plug work three way i.e. Vacuum creation, shutting off & vacuum releasing.
Material : Polypropylene / Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Desiccator (Vaccum) PP/PC 150 mm | 1 | |
| Desiccator (Vaccum) PP/PC 200 mm | 1 | |
| Desiccator (Vaccum) PP/PC 250 mm | 1 | |
| Desiccator (Vaccum) PP/PC 300 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 150 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 200 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 250 mm | 1 | |
| Desiccator (Vaccum) (All Clear) PC/PC 300 mm | 1 |
Mini Vertical Electrophoresis
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
3 Axis Robotic Trainer
For beginners, this Trainer is very useful to learn the concept and working of a Robo. For experienced people, this helps to make new ideas. This is used to study the ROBO characteristics of arm movement. Each axis has one AC servo motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move. Windows based user friendly software to control the arm through microcontroller having the flexible features such as
Features
• Easy to learn • New design • Easy for maintenance • Drive by AC servo motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 3 • Motor : AC servo Motor • Gripper : Pneumatic • Drive : AC servo Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 300º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit Switch
Three Step Inductor
Description
This three step inductor consists of a coil of enamelled copper wire wound over an insulated spool. The coil consists of 4 layers of 200 turns each. The tappings at 200, 400 and 800 turns are brought out at 4 mm sockets. The output inductances at these tappings are as follows. No. of turns Resistance 200, Inductor 0.3 mH, Resistance 0.6Ω No. of turns Resistance 400, Inductor 1.2 mH, Resistance 1.2Ω No. of turns Resistance 800, Inductor 5.0 mH, Resistance 2.6Ω. One can easily change the inductor value of the instrument on just inserting a soft iron core inside the bobbin
Microtome Razor
ZigBee Sensor Battery Board
ZigBee is one of the advanced Wireless technology and CC2530 is the Second Generation System On chip, Which has integrated Microcontroller with IEEE 802.15.4 Compliant and ZigBee RF transceiver. Vi ZigBee development Kit includes the hardware using CC 2530 and software to support the ZigBee protocol.
Features
• 2-AA battery holder integrated • 2 user LEDs • 2 user key • Light sensor • ADC Trim pot • RF Module connectivity • USB to serial connector • ADC channels are terminated via 3 pin connectors • All the IO lines are terminated via 20 pin header • 3 pin connector provision for I2C and SPI interface.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Microscope Slide Set Basic
Set of 25, Microscope slides created
Biology syllabus with following subjects.
Supplied in Box.
Kidney TS
Allium root tip LS, mitosis
Kidney VS, injected
Allium root tip, squash
Squamous epithelium
Moss leaf, for cells (check cells)
Leaf epidermis
Human blood smear
Stem, TS, separate bundles
Artery and vein
Mucor, asexual
Monocot (Zea) root, TS
Lung through bronchiole VS
Hair insertion
Ovary VS
Testis TS
Spinal cord, TS
Pancreas
Leaf, TS
Stem, LS old
Dicot stem apex, LS
Lung injected
Lily anther, Tetrad
RAY OPTICS KIT
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Bernoulli S Theorem Apparatus
DESCRIPTION:-
The Set-up is designed to verify Bernoulli’s Theorem experimentally. Set up consists of a one piece clear acrylic test section with convergent and divergent part section, supply tank, measuring tank, inlet water tank and pump for closed loop water circulation. The test section is connected to Piezometer tubes through pressure tapping at different locations on the section to demonstrate the Bernoulli’s Theorem. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:-
Ø To verify Bernoulli’s Theorem experimentally.FEATURES:-
Ø Clear test section Ø Closed loop water circulation Ø Compact & stand alone setup Ø Stainless Steel tanks and wetted parts Ø Superb Painted structure Ø Simple to operate & maintainUTILITIES REQUIRED: –
Ø Electricity Supply: Provide 230 +/- 10 VAC, 50 Hz, Single Phase electric supply with proper earthing (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump Ø Water Supply : Tap water connection ½ “ BSP, Distilled water @ 60 Ltrs. (Optional)TECHNICAL SPECIFICATION: –
Ø Test Section : Material Acrylic, Size Ø Inlet Tank : Capacity 20 Liters., Stainless Steel Ø Supply Tank : Capacity 70 Liters., Stainless Steel Ø Measuring Tank : Capacity 20 Ltrs. Fitted with Piezometer Tube & Scale Ø Piezometer Tubes : Material P.U. Tubes (9 Nos.) Ø Pump : FHP Capacity make Tullu/Crompton Graves Ø Piping : GI / PVC Size BSP Ø Stop Watch : Electronic Ø The whole Set-up is well designed and arranged in a good quality painted Structure.
Gat Tap, Superior
Description
Made of brass with superior black powder coating. Heavy construction having lever handle with locking arrangement to ensure lever rotation does not go beyond 90°. Output nozzle having 4mm bore. Inlet 3/8 X 26. Flange diameter 50mm with two holes to fix on bench or any other surface with screws. Provided with adapter (6/8, 3.8mm bore) and corresponding nut (8mm bore). Designed to operate at pressure up to 2 psi (0. 14kg/cm2). Suitable for use with coal gas, natural gas and L.P.G.Particulars
Gas Tap, One Way Gas Tap, Two Way Gas Tap, Three Way Gas Tap, Four Way
Primary and Secondary Coil
Description
The apparatus demonstrates the principle of Electromagnetic Induction and helps explain the concept of a transformer. Primary and Secondary coil consist of coils mounted on plastic spools, with 2 binding posts on each coil. You can slide the primary coil inside the secondary coil. Also includes a soft iron core for induction experiments. Primary coil has 480 turns while secondary coil has 3800 turns. Requires a galvanometer and bar magnets, not supplied with apparatus.
Insect Box with Stretching Strips
Description
Suitable for taking in field where the insects can be stretched on the spot and can securely be kept inside the box Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with EVA sheet over which adjustable strips provided for stretching insects. Strips can be fixed at one place with fine screws and fly nuts. Fitted with brass hinges, index card holder, clips and handle. Size Approx. 43 x 30 x 11cm.
BOD Incubator
Specification
BOD Incubator is designed for low temperature incubation and determination of Bio Chemical Oxygen Demand (B.O.D). The BOD Incubator comes with a double wall construction. The Inner chamber is made of richly anodized aluminum or highly polished stainless steel with two / three removable perforated shelves. The exterior chamber of the BOD Incubator is made of thick mild steel sheet duly finished in enamel paint. Outer double wall door is provided with magnetic gasket and lock & key arrangement. The inner door is made out of clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipment are filled with glass wool for temperature insulation. The cabinet is mounted on castors. The temperature in the BOD Incubator is controlled by a sensitive thermostat from 5oC to 50oC ± 1oC. For lower temperature working, a standard cooling unit with sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has made within the chamber for higher temperature. Inner air circulating system is provided to achieve uniform temperature in the whole chamber.| Inner Chamber Size | Cap. | Material |
|---|---|---|
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | Aluminium |
| 455 x 410 x 610 mm | 4cu. Ft. or 112 Ltr. | S.S. |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | Aluminium |
| 505 x 451 x 830 mm | 6cu. Ft. or 171 Ltr. | S.S. |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | Aluminium |
| 565 x 565 x 865 mm | 10cu. Ft. or 280 Ltr. | S.S. |
Optional
Timer 0-24 hours day night cycle. Internal illumination with 3 fluorescent tubes. Digital temp. Indicator-cum-Controller.
Constant Mesh Gear Box Actual Cut Section
Constant Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
