XTEMOS ELEMENT
AJAX PRODUCTS TABS
Light Dependent Resistor Unit (LDR)
Amplitude Shift Keying Modulation And Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Amplitude shift keying Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supply of ±12 V, +5 V.
2. 100KHz with 5 Vpp amplitude (Approx.) for carrier frequency.
3. In built square wave data generator.
4. Circuit diagrams for Modulator and Demodulator are printed on the milky white top panel.
Flower & Embryology
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Typical flower showing parts Fertilization showing germination of pollen T.S Anther & its development Germination of pollen grain and development of male Gametophyte Megasporogensis Development of embryo and endosperms Development of embryo in sagittaria Embryo in Capasella Microsporangium Types of emchryo sacs Forms of Androecium Form of Gynaecium Development of Monocot embryo Placentation Aestivation L.H. Datura Inflorescene Part – I showing simple racemose & simple cymose Inflorescene Part – II showing compound & special Pollination different types Forms of ovules Forms of Calx & corolla
Wankel Engine Model
The model demonstrates the principle, operation. It is cutaway to show the internal constructional details. Unlike other engines the rotary piston engine avoids reciprocating parts. The power pistons an arch like triangular rotor which on rotating generates an epitrochoid. Mounted on metal base with printed diagrams.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Geographical Terms
Regular Panel Meter, Large Size
Interference Undercutting
The board shows the demonstration of this phenomenon of Interference and Undercutting. When we rotate the teeth in anticlockwise direction, as the teeth is undercut is gives us a smooth working. When we give a rotation in clockwise direction, we can observe that the rack tip will be resisted by the tooth flank thus giving interference.
Outside Micrometers Engraved Marking
Description
Micrometer is used to measure short lengths accurately Technical Details : Engraved Marking On The Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop ; Least Count : 0.01mm/0.001” ; Sizes ; 0-25 ; 25-50 ; 50-75 ; 75-100 ; Specifications Guarantee 6 Months without abuse Packing ; Plastic Box Calibration ; In house.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Ray box Multi Slit
Tape Measures
Both sides metric or one side metric and other in feet-inches Fiber glass with PVC covering.
Non-conducting, waterproof, washable, and water-resistant.
Case made of zinc-coated steel sheet, covered with vinyl, & fitted with a flush winding handle.
all metal fittings are chrome-plated.
The Tape Measures are provided in size 5 meters, 10 meters, 15 meters, 20 meters, 25 meters, 30 meters.
Slide Wire Wheatstone Bridge
Description
Consists of a resistance wire with a sliding contact and a strip of aluminum to provide two “arms” of the bridge for known and unknown resistance. Strips of heavy aluminum are provided with a single gap in each of two arms for the resistance. All components are mounted on a heavy sheet metal base with Instructions.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Earthy Minerals Collection
Thermal Conductivity Of Insulating Powder
The apparatus consists of an insulating powder, which is enclosed in a cavity of two concentric spheres. The inner space of the inner sphere contains the mica heater. Input to the heater can be adjusted by the dimmerstat. The tappings on the surfaces of the inner sphere and outer sphere are used to find out the temperature difference between the spheres. This enables to find out the conductivity of powder.
Specifications:
1.Inner sphere dia. 100mm and outer sphere dia. 200mm. 2.Mica heater two heat the inner sphere surface. 3.Ten thermocouple tappings in the test section. 4.Plaster of Paris / asbestos powder in the test section. 5.Panel comprises of a)Voltmeter and ammeter b)Dimmerstat c)Temperature indicatorServices required:
1.220v stabilized single-phase supply. 2.Floor surface 1m x 0.5m at working height.
Water Bath Recangular Type
Specifications
It is a double walled unit inner chamber made up of S.S. Sheet and outside of M.S. duly powder coated. The gap between the walls is fitted with special grade glass wool in order to avoid thermal losses. Concentric rings can be removed to accommodate containers of various sizes. Temperature from ambient to 100°C is controlled by Hydraulic capillary type thermostat with accuracy of ± 1° C . Workable on 220V AC 50Hz Single Phase.| Chamber Size In mms | Holes | Cap. (Aprox.) |
|---|---|---|
| 300x250x100 | 6 holes of 75 mm | 8 L |
| 355x405x100 | 12 Holes of 75mm | 15 L |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
6 Axis Robotic Trainer
For beginners this kit is very useful to learn the concept and working. For experienced, this kit helps to make new ideas. This kit is used to study the ROBO characteristics of arm movement. Each axis has one stepper motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move.
Features
• Easy to learn • New design • Easy for maintenance • Drive by stepper motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 6 • Motor : Stepper Motor • Gripper : Pneumatic • Drive : Stepper Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 320º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit Switch
Model of Female Breast
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Tray Dryer
| Design | Standard, Customized | |
| Capacity | 96 trays | |
| Automatic Grade | Automatic, Semi-Automatic | |
| Max Temperature | 250 degree C |
| Chamber Size (HxWxD) | Tray Capacity mm Inches | |
|---|---|---|
| 430x840x650 8Tray | 16”x32”x 1 1/4 | |
| 430x840x910 12Tray | 16”x32”x 1 1/4 | |
| 910x840x910 24Tray | 16”x32”x 1 1/4 | |
| 960x1270x1450 45Tray | 16”x32”x 1 1/4 | |
| 960x1700x1700 96Tray | 16”x32”x 1 1/4 |
Optional
Timer 0-24 hours. Digital temp. Indicator-cum-controller. Tray 16”x32”x 1 1/4 size.
Signal Generator
1 Hz to 100 KHz in five decade ranges selected by rotary switch named as frequency Multiplier. Sine Triangular and Square waveforms selected by push switch with LED indication. Output signal is 0-3.5 V rms (10 V peak to peak) open circuit continuously control with uncalibrated amplitude control knob. Mains rocker switch with indicator Light. Signal Generator is versatile for general laboratory use; output signal is adjustable with the combination of Freq. multiplier and set frequency dial with a low level of distortion. Output Voltage is continuously variable with selector range 1V and 10V. There is two pair of output safety sockets. One for CRO output (experiment for amplification, filter etc.) and another pair of sockets to speaker to drive a speaker and to demonstrate the audio signal frequency range 20 Hz to 20 KHz.
Differential Gear Assembly Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Wooden Lever Apparatus
Made of wood, one meter long graduated scale is balanced on knife edge of the fulcrum. Supplied with 2 sets of 100 g weights.
One meter long with fulcrum lever is graduated in centimeters and is balanced on the fulcrum by a transverse groove cut midway in the length of the lever over knife edge of the fulcrum, supplied with 2 sets of 100 g weights.
