XTEMOS ELEMENT
AJAX PRODUCTS TABS
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
PLC-Logo 6 Pack with Demo Panel Trainer Kit
This Training kit based on Siemens model “Logo” PLC controller, is modulator, versatile, scalable & flexible with integrated Ethernet interface. Many features like High Speed configurable Analog Input etc make it as an Ideal PLC for basic training purpose
PLC Specification
• Make : SIEMENS • Model : CPU LOGORCE • Input Supply : 12/24V DC • Timers &Counters : 256 Nos Each • Digital Inputs : 8 Nos • Digital Outputs : 4 Nos • Program Memory : 400 Blocks • 4 Inputs can be configured as Analog Input (0-10V) DC • Optional SD cards for data logging • Ethernet Communication Interface • Networking with up to 8 unitsDemo Panel Specification
• 8 Nos of toggle switches & LEDs provided for Digital Inputs • 6 Nos of LEDs provided for Digital outputs indication purpose • All I/Os are terminated into SP7 connectors for external trainer interfacing • Patch chords provided for interfacing the external trainers • Modules and all the components mounted on an attractive powder coated metal cabinet • Mimic diagram with screen printing provided in the panel
SILICON RUBBER CORK
PRODUCT DESCRIPTION
A Bung, Stopper or Cork is a truncated cylindrical or conical closure to seal a container such as bottle, tube or barrel. Unlike a lid, which encloses a container from outside without displacing the inner volume, a bung is partially inserted inside the container to act as a seal. These can be used for all types of glass bottles. These stoppers fit tightly to prevent chemical leaks. We are one of the very few manufacturers of silicone rubber corks, septa gasket, silicone rubber stoppers in India.
Features:
- Silicon rubber cork / stopper /bung,
- Silicon rubber cork for filtration flask.
Cylinderical Magnet
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Model of Uterus And Ovaries
Triangle Kit
Mirror, Plane
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Human Torso, With Head, Half Size
Digit Counter Micrometer (DCM)
Description
Micrometer is used to measure short lengths accurately Technical Details : Printed Marking on the Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop Least Count : 0.01mm With Digit Counter to withstand abuse at work Sizes : 0-2 25-5 50-7 75-100 Specifications: Guarantee ; 6 Months without abuse Packing ; Plastic Box Calibration ; In house.
Water Bath Incubator Shaker
Specifications
Similar to other water bath but fitted with inbuilt shaker for differrent experiments demanding shaking at constant speed under controlled temerature conditions. The temprature is controlled by capillary type thermostat from ambient to 100°C. RPM range :- 40-140 with variable electronic speed regulattor workable on 220V AC 50 Hz Single Phase.| Chamber Size In mms (dia x depth) | Capacity (L) | |
|---|---|---|
| 275x275x150 | 12 L | |
| 405x300x150 | 18 L |
Optional (Extra Cost)
Microprocessor PID digital temp. indicator cum contrroller. Digital RPM meter. Auto cut off device when water level is low.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Turbo Charger Actual Cut Section
The working of turbo charger is shown with the help of actual parts assembled on iron base. All the necessary parts of turbo charger are shown in actual working form. This model helps the student to understand the working of the turbo charger very easily. It is specially made dissectible for demonstration purposes.
TI MSP430 Development Board
ON Chip Features
• CPU - MSP430F1611 • Core - 16 bit RISC Architecture. • Speed - Up to 8 MHZ. • Flash - 48 KB + 256B. • SRAM (on-chip) - 10KB. • 48 GPIO Lines. Two UARTs. • One I2C Module. One SPI Module. • Two 16 bit Timers. • Five Power Saving Mode. • 12 bit ADC with single channel. • 12 bit DAC with two channel.ON Board Features
• Eight Digital Output - LED Interface. • Two Digital Input. • 16 x 2 Character LCD Interface. • 7 Segment Display via I2C Interface. • 10 Base T Ethernet Connectivity. • SD Card Interface Support. • Audio Interface. • Jtag connector is provided for Debugger. • USB to serial interface provided.
Outside Micrometers Engraved Marking
Description
Micrometer is used to measure short lengths accurately Technical Details : Engraved Marking On The Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop ; Least Count : 0.01mm/0.001” ; Sizes ; 0-25 ; 25-50 ; 50-75 ; 75-100 ; Specifications Guarantee 6 Months without abuse Packing ; Plastic Box Calibration ; In house.
Laboratory Stirrer
Laboratory Stirrer (Mechanical Stirrer)
Fitted with speed regulator, height and space adjustable 1/20 H.P.
AC/DC Motor.
Features
Stir power: 150 W. Stirring and heating volume: up to 80L (H2O). Stir speed: 60- 1500rpm. rotate speed display, time accurate, acceleration precise structure, bidirectional mixing.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Test Tube Caps
The Test Tube Caps offered by us, come with a transparent polypropylene cap for test tubes, which proves to be an excellent protection to the contents of the tubes.
The grooves inside the cap tighten the fitting on the tube while the outer set in the tube making the combination a leak proof one.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Test Tube With Screw Cap 16 x 100 mm | 500 | |
| Cap For Test Tube Ø 25 mm | 500 |
Table Counter Suitable for 100 tablet
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.
Level Process Station
Panel Features
• Digital Panel Meters. • Mimic diagrams. • Pressure gauges are provided, wherever necessary. • Level switches are provided for overflow indication.Features
• The Level Process Station is an attractive module. • All are the industrial (4-20) mA standard interfacing signals. • It provides a real industrial feeling of the processes to the students. • A RF Capacitance level transmitter is used to sense the level (700mm) of tank. • An Electronic Regulated Power supply is fixed for voltage regulation. • An Air regulator cum filter is provided to regulate the air pressure. • An Industrial standard electro pneumatic converter is mounted to control the control valve. • A Globe pneumatic control valve is used to control the flow rate • All the air flow lines are fitted by flexible hoses/fittings for better reliability. • A Rotameter (1000 LPH) is provided for Visual Indication of flow rate. • A Transparent Process Fiber tank (800mm) with graduated level scale. • A Solenoid Valve is provided for Load Disturbance study. • A Rust proof Reservoir Tank (SS) capacity of 45 Liter. • By pass line is provided to avoid pump over loading. • A Centrifugal Pump is used for water circulation. • All components are fixed in a mobile rack. • All water flow lines are fitted by SS pipes. • USB/Serial port data acquisition is provided.
Rain Gauge
Description
Rain gauge is designed to measure the precipitation. This small Version consisting of upper and lower housing part, measuring cylinder; Housing made of stainless steel, orifice rim made of brass. Type 7019.0000 can be supplied with a receiving area of 100 cm2. (This type is not conforming to meteorological standards). • Receiving area : 100 cm². • Rain measure (graduated glass) : 250 cm³. • Measuring range : 0 t0 25 mm precipitation (relative to a receiving area of 100 cm²). • Graduation : 1/1 mm precipitation. • Dimensions : dia 115 mm; height 300 mm. • Weight : approx. 0.8 kg.
