Plug type, with three pairs of ratio coils of 10,100 and 1000 ohms and 16 series coils from 1 to 5000 ohms, total 11,110 ohms, giving a range from 0.01 ohm to 1,111,000 ohms.
Two tapping keys are provided for battery and galvanometer.
Accuracy ratio coils ±0.05%, others ±0.1%
With two ratio dials of 10,100 and 1000 ohms each and a resistance arm of four dials, each of ten coils of 1, 10, 100 and 1000 ohms, giving total resistance of 11,110 ohms with 4 mm socket terminals for battery, galvanometer and unknown resistance.
Highly stable resistances are used.
Accuracy ±0.1%
A one meter long single resistance wire passes over a meter scale and is firmly clamped to stout brass end-plates, on wooden base.
Complete with knife-edge jockey
For Westminster Electromagnetic Kit giving 1 V full wave rectified DC and 1 V / 2 V AC outputs at 8 A max.
The circuit diagram is printed on the top panel which also carries mains switch, light indicator and output sockets for DC and AC With 1.5 meter mains detachable cable.
The apparatus demonstrates the principle of Electromagnetic Induction and helps explain the concept of a transformer.
Primary and Secondary coil consist of coils mounted on plastic spools, with 2 binding posts on each coil.
You can slide the primary coil inside the secondary coil.
Also includes a soft iron core for induction experiments.
Primary coil has 480 turns while secondary coil has 3800 turns.
Requires a galvanometer and bar magnets, not supplied with apparatus.
Resistance Box kit is an excellent device, which provides a very good learning technique in making different combinations of resistances, either in series or in parallel or in both ways to obtain the desired value of resistance for any circuit application.
It consists of 10 resistors of equal values, i.e., 10Ω , 2 watts.
These resistances are of ± 1% tolerance
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops.
The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used.
Coils are non-inductively wound and are treated to be strain-free.
Coil values are engraved on the plate and an infinity plug is also included.
Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest
0.01 to 0.1 ohm, Total 0.2 ohm
0.1 to 1 ohm, Total 2 ohm
0.1 to 5 ohm, Total 11 ohm
0.1 to 10 ohm, Total 21 ohm
0.1 to 50 ohm, Total 111 ohm
0.1 to 100 ohm, Total 211 ohm
0.1 to 500 ohm, Total 1111 ohm
1 to 10 ohm, Total 20 ohm
1 to 50 ohm, Total 110 ohm
1 to 100 ohm, Total 210 ohm
1 to 500 ohm, Total 1110 ohm
1 to 1000 ohm, Total 2110 ohm
1 to 5000 ohm, Total 11110 ohm
The kit illustrates that the resistance of a wire depends on its length, diameter and material of that wire.
Each of the eight coils is wound on plastic spools with brass terminals for easy connection.
The coils are stored in a clear plastic box.
Resistance Demonstration Set demonstrates the relation between resistance and cross section of different wires.
This set has 2 copper and 2 nichrome wires of different diameters.
A pair of colourcoded terminal used for power supply connection.
This set uses 6V DC to operate.
Set of 12 different value resistor from 33 Ω to 10 M Ω.
A rotary switch is used to select the required resistance, 4 mm sockets are provided for connections.
Resistance Substitution Box is a convenient instrument for determining the desired resistance values in circuits under design or test.
This resistance substitution box has 12 different values 100Ω , 220 Ω , 470 Ω , 1 kΩ , 2 kΩ, 4 kΩ , 10 kΩ , 22 kΩ , 47 kΩ, 100 kΩ , 220 kΩ and 470 kΩ .
All resistors are precision 1% resistors and are of 1 watt rating Selected resistor can be attached in any circuit with 4 mm two red safety sockets.