Description
Error: Contact form not found.
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes :
a)Gl pipe (innermost) – 6 cm. (Outer Diameter).
b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter)
c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter)
d)Length of pipes 1 Meter.
2.Heater :
Nichrome wire cartridge heater placed centrally, of suitable capacity.
3.Control Panel :
a)Single Phase Dimmerstat – 1 No.
b)Voltmeter (0 – 250V) – 1 No.
c)Ammeter (0- 2A) – 1 No.
4.Temperature Indicator :
Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI Thermocouples
Services Required:
1. A.C. Single Phase 230 V electric supply
2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Related products
Thermocouple Calibration Test Rig
The Unit helps in calibrating given thermocouple for the range 0°C to 100°C. While calibrating, thermocouple is once dipped in ice for 0Q C and then in boiling water for 100°C. This is done till the thermocouple shows the actual temperature of ice (0° C) and boiling wafer (100°C) and a linear calibration is set. A mV meter is provided to know the corresponding voltage.
SPECIFICATIONS:
1.A digital mV Meter and a digital temperature indicator with 2 different type of thermocouples. 2.A water container with heater of 1 KW. 3.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Table surface area – 2 m X 1 m X 0.5 m height. 2.220V, 50hz. Stabilize Electric Power Supply. 3.Ice cubes – 0.5Kg. Approx.
Pin Fin Appatatus
The apparatus consists of a channel in which the pin fin is tested in both natural as well as forced convection. The channel is connected to the suction of blower. The blower is operated to touch the pin fin in forced convection only. In natural convection, the window above the pin fin is kept open to the atmosphere. Five thermocouple tapings are given along the length of the fin. Thus the temperature distribution along the length can be distinguished. Also natural and forced heat transfer co-efficient, effectiveness, etc. can be found out.
Specifications:
1.Three pin fins- a) M. S. b) Brass c) Al 2.Channel- 150mm x 100mm x 1000mm 3.Blower – run by f.h.p. motor. 4.Orifice meter along with water manometer to measure airflow. 5.Voltmeter and ammeter to measure power input. 6.Cr- Al thermocouple with 6 tapings along with temperature indicator. 7.Dimmerstat to control power input. 8.A band heater to heat the pin fin. A technical manual accompanies the unit.Services required:
1.220v, stabilized single phase supply along with earthing Connection. 2.Floor area 2m x 1m x 1m height.
Thermal Conductivity Of Insulating Powder
The apparatus consists of an insulating powder, which is enclosed in a cavity of two concentric spheres. The inner space of the inner sphere contains the mica heater. Input to the heater can be adjusted by the dimmerstat. The tappings on the surfaces of the inner sphere and outer sphere are used to find out the temperature difference between the spheres. This enables to find out the conductivity of powder.
Specifications:
1.Inner sphere dia. 100mm and outer sphere dia. 200mm. 2.Mica heater two heat the inner sphere surface. 3.Ten thermocouple tappings in the test section. 4.Plaster of Paris / asbestos powder in the test section. 5.Panel comprises of a)Voltmeter and ammeter b)Dimmerstat c)Temperature indicatorServices required:
1.220v stabilized single-phase supply. 2.Floor surface 1m x 0.5m at working height.
Theramal Conductivity Of Insulating Slabs
The apparatus consists of a slab assembly. The main Heater and a radial guard heater are sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other Sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates. By knowing the temperatures and Heat input, thermal conductivity of specimen can be calculated. The test set up is enclosed in an enclosure with insulation inside to provide undisturbed Surroundings. The design style of the apparatus is similar to as recommended in INDIAN standard. The difference is in sizes.
SPECIFICATIONS:
1.Heaters: a)Main heater plate 110 mm dia. with mica heater Sandwiched between copper plates. b)Radial guard heater plate I.D. 120mm and OD 200 mm mica heater sandwiched between copper plates. 2.Water circulated cooling plates -2 nos. 3.Dimmerstat-2 A capacity – 2 nos. to independently control Inputs to the heaters. 4.Measurements – A voltmeter and an Ammeter with selector switches to measure inputs,Multichannel digital temperature indicator to measure Temperatures at various points, having 0.1 °c least count. A technical manual accompanies the unit.SERVICES REQUIRED:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Water supply of about 4-5 lit/min. 3.Bench area 1m x lm x O.5m height.
Concentric Tube Heat Exchanger
(A)Plain Tube ( Water To Water ):
The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. While the outer tube consists of GI pipe through which cold water flows. The arrangement enables the parallel and counter flow of the cold water. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.
Specifications:
1.Inner copper tube I.D, 12.7mm. and outer G. I. Pipe I. D. 15mm. approx. and 1.5m. length. 2.Thermometers – 4 nos. 3.Measuring flask – 1 Lit. capacity. 4.Geyser-3 kW. Single phase.Services required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x I m x 1 m height. (B) Finned Tube ( Water To Air ): The apparatus consists of two concentric tubes. Inner tube consists of copper tube through which hot water flows. It is finned at its outer diameter to increase the heat transfer surface. While the outer tube consists of GI pipe through which cold air flows. The arrangement enables the parallel and counter flow of the air. The inlet and outlet temperatures and the flow measurement enable to find out the heat exchanged LMTD, and effectiveness of the equipment.Specifications:
1.Inner copper tube I.D. 12.7mm. and outer G. I. Pipe I. D. 25mm. approx. and 1m. length. 2.Thermometers – 4 nos. 3.Orifice meter along with manometer. 4.Measuring flask – 1 Lit. Capacity. 5.Geyser-3 kW. Single phase.Services Required
1.220v, 15A, stabilized single-phase AC supply. 2.Floor area – 3m x 1m x 1m height.
Composite Walls Apparatus
Composite Walls Apparatus:
The apparatus consists of a pair of M.S. plates, Bakelite, brass/aluminum. These plates in series on either side of the heater form a composite wall. The whole unit is clamped in a frame, which can be viewed through the Perspex sheet. The thermocouple tapings enables us to find out the conductivity and resistance of the composite walls.
SPECIFICATIONS:
1.Heater- Mica healer of dia. 250 mm. 2.Plates- a) M.S. plates of thickness 25mm & dia. 250mm.-2 nos. b) Bakelite plates of thickness 10mm & dia. 250mm.-2 nos. c)Brass/Aluminum plates of thickness 15mm & dia. 250mm.-2nos 3.Dimmerstat – 2 A capacity. 4.Measurements — a) voltmeter and an Ammeter to measure input power. b) Multichannel digital temperature indicator to measure temperatures at- various points. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, A.C. stabilized supply along with earthing connection. Bench area Im x lm x 0.5m height
Heat Transfer In Aagitated Vessel
The unit consists of a vessel with class wool insulation ail around. A helical coil made of copper is fixed inside the vessel. A motorized agitator is fixed at the center of the coil. The vessel is provided with an electric heater and a controller is also provided for vessel. Heater heats water in the jacket while cold water is circulated through coll. Temperature of circulated water and water In vessel Is measured and thus heat transfer coefficient at various agitator speeds can be determined.
SPECIFICATIONS:
1.Vessel approx. 20 lit. capacity, provided with glass wool insulation all around and electric heater at the bottom. 2.Agitator 150 mm dia, with 1/8 HP motor to drive the agitator. 3.Helical coil – 200 dia, 8 turns, made of 3/8″ dia. copper tube. 4.Controllers for heater and agitator motor. 5.Temp. Indicator for vessel water temperature and circulated water inlet and outlet.SERVICES REQUIRED:
1.Single phase 230V, 15 A stabilized supply. 2.Water flow at the rate of 4 to 5 lit. per min. 3.Suitable drain arrangement for water. 4.Floor area -1.5 mtr. X 1 mtr. X 1 mir height.
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
Reviews
There are no reviews yet.