Wet Dry Thermometer

The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.

SPECIFICATIONS:

1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.

SERVICES REQUIRED:

1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connection

Desert Cooler Trainer works on the principle of evaporative cooling. It is used mostly in the dry hot regions; it consists of a fan which sucks the air from atmosphere through the pads which are used in desert coolers very frequently. The difference in DBT & WBT at inlet and outlet can be measured hence the RH from the charts. Also the amount of water evaporated can be calculated by knowing the water level difference in the reservoir.

SPECIFICATIONS:

1.Fan connected to 1/2 HP motor. 2.Air Cooler Pump to circulate water. 3.DBT & WBT Measuring Thermometer at inlet and outlet. 4.Orifice meter with manometer to measure the air flow. A technical manual accompanies the unit.

SERVICES REQUIRED:

1.Floor Area – 1, X 1 m. X 1 -5m. Height. 2.220 V., 15 Amp. , Single Phase Stabilized power supply

Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.

SPECIFICATIONS:

1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.

SERVICES REQUIRED:

1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.

This apparatus is used to calculate the wind or air velocity it has a special probe that can easily enter into air ducts. We can place the anemometer inside the air ducts of air conditioner and record the air velocity.