XTEMOS ELEMENT
AJAX PRODUCTS TABS
Flower & Embryology
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Typical flower showing parts Fertilization showing germination of pollen T.S Anther & its development Germination of pollen grain and development of male Gametophyte Megasporogensis Development of embryo and endosperms Development of embryo in sagittaria Embryo in Capasella Microsporangium Types of emchryo sacs Forms of Androecium Form of Gynaecium Development of Monocot embryo Placentation Aestivation L.H. Datura Inflorescene Part – I showing simple racemose & simple cymose Inflorescene Part – II showing compound & special Pollination different types Forms of ovules Forms of Calx & corolla
Distributed Control System
A powerful, modular & upgradable DCS has been designed and configured based on Siemens controller SIMATIC PCS7 ASRTX (Micro Box). Distributed I/O system ET200M can be provided for field automation. The distributed I/O can be connected via Profibus, Communication. DCS consists of controller, Power supply unit, distributed I/O, Digital Input and Output modules, Analog Input and Output module. a Demo Panel and Simatic PCS7 V9.0 Software.
DCS Controller
• Make : SIEMENS. • Controller : SIMATIC PCS 7 AS RTX BOX. • Profibus Communication done via CP5611 onboard. • Transmission Rate of Profibus cable is 12 Mbit/s. • 2 x GBIT & RJ45 LAN • Core 17-3517 Processor 1.7GHz, 4GB DDR3 RAM, SSD 80GB, 4xUSB V3.0 • Mouse and Keyboard • Windows7 • Win AC RTX 2010 software controllerDistributed I/O station ET200M
• Support HART, PROFIBUS, Foundation Field bus. • 16 No’s of digital Inputs with 24V DC. • 16 No’s of digital Outputs with 24V DC. • 8 channels of Analog Inputs with 4-20mA. • 8 channels of Analog Outputs with 4-20mA. • 24VDC /10A inbuilt power supply.
Polishing Pan
Earthy Minerals Collection
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Turbine/Pump Unit
Description
For use as a water turbine to drive a generator producing electricity or for use as a pump driven by a motor and raising a head of water to produce potential energy. The rotor has eight 'bucket' blades and is housed in a block turbine chamber with a clear Perspex front. Two inlet tubules (for turbine and pump operation respectively) and one outlet tubule are provided and the shaft carries a 15 mm. diameter pulley. With driving belt.
Thermal Conductivity Of Liquid
Thermal conductivity of is an important engineering property. The apparatus uses guarded hot plate method for determining thermal conductivity. It consists of hot plate i.e. an electrical heater sandwiched between two plates. The heat loss from hot plate is prevented by using two guard heaters and heat of removes heat from liquid by circulation of water. Input to heaters the temperatures.
SPECIFICATIONS:
1.Guarded hot plate assembly comprising of main heater, ring guard heater and top guard heater, mounted over the liquid test cavity. 2.Cold plate assembly provided with water connections. 3.The assembly is housed in an enclosure box with glass wool insulation. 4.Instruments panel consisting of : a).Digital voltmeter and ammeter of suitable range. b).Dimmerstat for controlling input to the heaters (2 amp. 3 Nos.) c).Multichannel digital temperature indicator.SERVICES REQUIRED:
1.Floor space of about 0.75m. x 1.5m. at working height. 2.230v. AC electrical supply with earthling connection. 3.Water flow rate of about 10- 15 lit/min. at constant head.
Larynx, 2 Parts
Constant Mesh Gear Box Actual Cut Section
Constant Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Conical Measures
The Conical Measures offered by us are very effectively for measuring small quantities of reagents.
Moulded in Polypropylene, these autoclavable measures have a hexagonal base, which provides it excellent stability.
The measures are clear, have good chemical resistance, and have raised graduation for easy.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Conical Measure 12 ml | 12 | |
| Conical Measure 25 ml | 12 | |
| Conical Measure 50 ml | 12 | |
| Conical Measure 125 ml | 12 | |
| Conical Measure 200 ml | 12 |
Model of Compound Microscope (BI STU)
Laplace Law Apparatus
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Anti Lock Braking System ABS Trainer
Anti Lock Braking System (ABS) Trainer
All modern car are now days fitted with anti lock braking system. This trainer helps the students to understand the working of ABS. The trainer consists of the following parts.
1. Control Panel,
2. Break Light,
3. ECU,
4. ABS Hydraulic Activator,
5. Break Lever,
6. Pressure Gauges,
7. Common Pressure Gauge.
An anti-lock braking system (ABS) is a safety system that prevents the wheels on a motor vehicle from locking up (or ceasing to rotate) while braking. A rotating road wheel allows the driver to maintain steering control under heavy braking by preventing a skid and allowing the wheel to continue interacting tractively with the road surface as directed by driver steering inputs. ABS offers improved vehicle control and decreases stopping distances on dry and especially slippery surfaces for many drivers, but on loose surfaces like gravel and snow-on-pavement it can slightly increase braking distance, while still improving vehicle control. Stopping a car in a hurry on a slippery road can be very challenging. Anti-lock braking systems (ABS) take a lot of the challenge out of this sometimes nerve-wracking event. In fact, on slippery surfaces, even professional drivers can’t stop as quickly without ABS as an average driver can with ABS.
Open Wind Tunnel Apparatus
Technical Description
A wind tunnel is the classic experiment system for aerodynamic flow experiments. The model being studied remains at rest while the flow medium is set in motion, and thus the desired flow around the model is generated. Open wind tunnel used to demonstrate and measure the aerodynamic properties of various models. For this purpose, air is drawn in from the environment and accelerated. The air flows around a model, such as an aerofoil, in a measuring section. The air is then decelerated in a diffuser and pumped back into the open by a fan. The carefully designed nozzle contour and a flow straightener ensure a uniform velocity distribution with little turbulence in the closed measuring section. The flow cross section of the measuring section is square. The built-in axial fan with guide vane and a variable-speed drive is characterised by an energy-efficient operation at high efficiency. Air velocities of up to 28m/s can be reached in this open wind tunnel. The trainer is equipped with an electronic two-component force sensor.Lift and drag are detected and displayed digitally. The air velocity in the measuring section is displayed on the inclined tube manometer. The tube manometers is recommended for measuring the pressure curves in drag bodies. Extensive accessories allow a variety of experiments, for example lift measurements, pressure distributions, boundary layer analysis or visualisation of streamlines. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.Learning Objectives & Experiments
– Determine drag and lift coefficients for different models – Pressure distribution when flowing around drag bodies – Boundary layer analysis – Investigation of flutter – Wake measurementFeatures
* Open wind tunnel for a variety of aerodynamic experiments * Homogeneous flow through the flow straightener and special nozzle contour * Transparent measuring section
Human Tooth, Upper Triple Root In 2 Parts
BURETTE STAND
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Breeding Nest
CAVITY BLOCK
Dissecting Trays
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Botany Algae
Educational Equipments Manufacturer, Exporters & Suppliers - School Educational Equipments Manufacturers & Exporters of Educational Equipments for Lab.
Science Lab Products, Teaching Aids, Classroom Instruments, Educational Laboratory
| Nostoc WM | Nostoc Heterocyst | Oscillatoria WM |
| Chlamydomonas WM | Chara Veg. WM | Chara Reproductive |
| Chara Sexuals LS | Chlorella WM | Cladophora WM |
| Diatoms Mixed WM | Oedogonium Vegatative WM | Oedogonium Capcells WM |
| Oedogonium Nannandious WM | Spirogyra Vegetative WM | Ulothrix Vegetative WM |
| Ulothrix Reproductive WM | Volvox Colony WM | Volvox Daughter Colony WM |
| Ectocarpus Unilocular WM | Ectocarpus Unilocular WM | Ectocarpus Plurilocular WM |
| Focus Thallus TS | Fucus Male Conceptacle VS | Fucus Female Conceptacle VS |
| Sargassum Thallus (Leaf) TS | Sargassum Male Conceptacle TS | |
| Sargassum Female Conceptacle TS | Sargassum Bladder TS | Batrachospermum WM |
| Batrachospermum Fruiting WM | Polysiphonia Antheridial WM | Polysiphonia Cystocarp WM |
| Polysiphonia Tetrasporic WM | Polysiphonia Vegetative WM | Oedogonium Macrandrous WM |
| Vaucheria Vegetative WM | Vaucheria Reproductive WM | Spirogyra Scalariform Conj. WM |
| Spirogyra Lateral Conj. WM |
Bucket & Cylinder
For demonstrating Archimedes principle this is a simple form in brass, suitable for class demonstration or individual use.
The bucket has suspension loop at the top and hook at the bottom.
The cylinder has a suspension hook at one end. Size 6 cm long, overall length when extended 16 cm.
A Bucket and Cylinder
B Bucket and Cylinder Large Size
Analgesiometer Tail Flick
Analgesiometer Tail Flick (Radiant Heat or Tail Flick Type): It provides pain stimulus by heated nichrome wire in a Rat's tail to determine analgesic effect of drugs.
Complete with one spare element to work on 220 A.C.
Features
Shutter operated lamp illumination system. Automatic or manual mode for detecting tail flick. Precise and reproducible results. PC Connectivity with software. Software with calibration and report generation feature. Software with auto experiment number and serial number feature. Software with provision to convert data in excel or pdf. Cut off timer to avoid damage to animal. Calibration mode using Heat Flux meter (optional device).
MCS Family Microcontroller Trainer
Specification
• 89C51 Microcontroller operating at 12Mhz • 64KB on-chip internal Flash EEPROM program memory • 1KB on-chip data RAM • 64KB External Data RAM • 32KB EPROM for monitor program • 32KB RAM for Program/Data memory • 32KB RAM for data memory • 1KB On-Chip Data RAM • Battery backup for RAM • Onboard 16 x 2 Alphanumeric LCD Interface • Onboard IBM PC Keyboard Interface • RS232/RS485 compatible serial interface terminated at 9 pin 'D' male connector • One RS232 Cable • Onchip Programmable Counter Array (PCA) PCA Contains five 16 bit PWM/capture/compare output • 48 TTL I/O lines using 8255 terminated in two 26 Pin FRC Connectors • All CPU address, data, and control signals are terminated in a 50 pin FRC Connector (VXT Bus) for connecting the • VBMB series of Experiment boards. • All connections of the Microcontroller are terminated in a separate connector for expansion • Built-in Line assembler & Disassembler • Windows based In System Programming Software for Flash Memory programming
Rear Axial Assembly With Differential Gear Semi
Rear Axial Assembly With Differential Gear Semi Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
