XTEMOS ELEMENT
AJAX PRODUCTS TABS
Thermal Conductivity Of Metal Rod
The apparatus consists of a copper bar, which is heated at one end, a heat sink is provided at other end. The test section of bar is properly insulated and thermocouples are attached along the length of bar. Heat conducted through the section of bar is measured by heat collection in water-cooled heat sink. A panel comprising of controls and measurements is provided, which provides easy operation and sturdy mounting of unit.
SPECIFICATIONS:
1.Metal Bar – 25mm of adequate length, provided with 8 Thermocouples along the length, Band heater at one end and water-cooled heat sink at other end. Test portion of bar is insulated. 2.Instruments panel comprising of. Voltmeter … 1No. Ammeter … 1No. Dimmerstat 0-230v, 2A, capacity. Multichannel Digital temperature Indicator. 3.Measuring flask and stop clockSERVICES REQUIRED:
1.Bench area of 1.5m. x 1m. at working height. 2.230 v, AC, electric supply with earthing connection. 3.Water supply at the rate of 2 lit/mm
Simple Circuit Modules
Description
Designed to demonstrate to implement and applications of electrical, electronic devices and simple circuits. These modules are fitted with 4 mm sockets. Components are directly mounted on printed PCB with diagram.Various modules are available as following Resistor LDR LED Push Switch Motor Reed Relay Reed Switch Relay Nand Gate Buzzer Thermistor Lamp Holder Single Pole Double Throw Switch Electromagnet Power Transistor
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Resistance Box, Plug Pattern
Description
All plugs are turned to a fine standard taper and are interchangeable. These are moulded in fluted plastic tops. The brass blocks are undercut and are fitted to a thick insulating plate. Heavy 4 mm brass terminals are used. Coils are non-inductively wound and are treated to be strain-free. Coil values are engraved on the plate and an infinity plug is also included. Accuracy ±0.5% for 0.01 to 0.05 ohm coils, ±1% for the rest 0.01 to 0.1 ohm, Total 0.2 ohm 0.1 to 1 ohm, Total 2 ohm 0.1 to 5 ohm, Total 11 ohm 0.1 to 10 ohm, Total 21 ohm 0.1 to 50 ohm, Total 111 ohm 0.1 to 100 ohm, Total 211 ohm 0.1 to 500 ohm, Total 1111 ohm 1 to 10 ohm, Total 20 ohm 1 to 50 ohm, Total 110 ohm 1 to 100 ohm, Total 210 ohm 1 to 500 ohm, Total 1110 ohm 1 to 1000 ohm, Total 2110 ohm 1 to 5000 ohm, Total 11110 ohm
Spherometer Laboratory
Spherometer Laboratory
• Brass dial head 40 mm diameter, mounted on stainless steel screw.
• Head divided into 100 divisions, reading to 0.01 mm and registering on vertical scale 10-0-10.
• Frame with three legs of stainless steel.
• Distance between two legs is 40 mm approximately.
• Pitch 1mm.
Block, Glass
SCR VI Characteristics Study Trainer
Specification
• Basic VI characteristics study trainer. • Consists of one no. TYN612 SCR with heat sink. • LM723 based 20V DC power supply for gate voltage. • One no. potentiometer used to vary the gate current • 0- 30V DC variable power supply for anode, cathode voltage variation. • One no. potentiometer used to vary the Vak. • One no. high voltage fixed load resistor. • One no. toggle switch to ON/OFF gate voltage. • Two nos. DC ammeter, voltmeter/multimeter provided to measure Ig&Vak, Ia. • 230V AC input. Power ON/OFF switch. • All components are mounted on a screen printed PCB fixed on a nice wooden cabinets.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Car Chassis All Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Voltaic Cell Set, Student
Diffraction Object Holder
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Laboratory Spatula
Acquire from us high quality Laboratory Spatula at affordable price range.
Moulded in Polypropylene, Spatula consists of a spoon on one side while the other end is a flat construction with a knife edge.
This is helpful in breaking up crystals of different salts while the spoon is used to draw salts from the containers.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Spatula 150 mm | 12 | |
| Spatula 200 mm | 12 |
Water Table Model
Absolute Expansion Of Mercury Apparatus, Dulong & Petit
Description
To determine the co-efficient of absolute expansion of mercury. Glass tubes with vertical limbs contained within glass jackets approx. 460 x 25 mm height x diameter are closed by bungs and fitted with inlet and outlet tubes. Upper ends of these vertical limbs are angled on emergence from the jackets to produce two short, adjacent limbs placed against a silvered glass scale 0 to 12 cm x 1 mm. Mounted on stand 610 x 230 mm, height x width. Overall height 750 mm approx. supplied without mercury.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Typical Flower
PP Cryo Box
We bring forth the finest range of PP Cryo Boxes.
Moulded in Polypropylene, the top of the box is attached to the bottom through well designed built-in hinges.
The bottom has built-in spaces to hold vials up to 2 ml. Capacity.
Available in two different sizes, these autoclavable PP Cryo Boxes bear alpha numeric index for easy identification of different vials placed inside.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Box (P.P) - 81 places for 1 ml or 1.8 ml cryo vails | 4 | |
| Cryo Box (P.P) - 100 places for 1 ml or 1.8 ml cryo vails | 4 |
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supply
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.
