XTEMOS ELEMENT
AJAX PRODUCTS TABS
TMS320C6747 Based DSP Trainer
KEY FEATURES:
• TMS320C674x Fixed/Floating-Point VLIW DSP Core Operating upto 300MHz • 64 General-Purpose Registers (32 Bit) • Six ALU (32-/40-Bit) Functional Units • Two Multiply Functional Units • Instruction Packing Reduces Code Size • All Instructions Conditional • Hardware Support for Modulo Loop Operation • On Chip RTCON-CHIP MEMORY:
• Two Level Cache Memory Architecture • 32K-Byte L1P Program RAM/Cache • 32K-Byte L1D Data RAM/Cache • 256K-Byte L2 Unified Mapped RAM/Cache • 128K-Byte RAM Shared MemoryON-BOARD FEATURES:
• Boot mode selection Switch • 1M x 16 Bit x 4 Bank SDRAM. • 10/100M Ethernet Interface • USB1.0 & USB 2.0 Interface. • Embedded JTAG for Emulation. • 8 LED & 8 Switch for user Interface. • Expansion Connector For GPIO & Peripheral Interface. • VSDA Expansion Card for 4 Channels ADC & 4 Channels DAC. • Provision to connect external JTAG Emulator • RS232 Serial Port Interface
Tooth Hygiene Set
Siemens IoT 2020 Gateway
Specification:
• SimaticIoT 2020 Educational Intelligent gateway • Intel Quack Soc x 1000 • 400MHz operating frequency • Micro SD card slot, upto 32GB • 512MB RAM, 8MB Flash, 256KB SRAM • One USB controller and one USB device • FTDI USB to serial Interface • One no of 10/100Mbps Ethernet • Arduino Uno R3 compatible expansion slot • One mini PCIe expansion slot for WLAN/additional Ethernet port • Yocto V2.1 based Linux operating system • Input supply 24V DC • Programming in high level language • Support for various protocols like Modbus RTU, POC UA and cloud protocols like MQTT/AMQPXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Hydraulic Power Steering System Motorised
Hydraulic Power Steering System (Motorised) – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Pin Hole Camera
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Monocot Stem Anatomy T.S &L.S
Description
This model exhibits the various tissues and the scattered, closed and collateral vascular bundles in transverse and longitudinal sections in maize. The large pitted vessels, spiral and annular vessels show the cell wall thickenings in L.S. Useful model for teaching anatomy of monocot stem. Mounted on base with keycard.
Tubes, Amber Colour Culture, Media, Round Bottom with Screw Cap and PTFE/Rubber Liner
Multi-Functional Nursing Simulator (Female)
Description
Designed according to the demand of the clinical principles and the guidelines of nursing training. This multifunctional simulator could simulate an actual circumstance for practice. Multiple functions, rural practice, easy assembly, well shaped appearance and correct anatomical landmarks provides a very good training for practice.Features:
Head Care. Body care. Patient moving. Different lying pose. Bilateral and Unilateral oxygen inhalation. Atomization inhalation therapy. Nasal Feeding. Gastric lavage training. Intravenous Injection. Intramuscular Injection. Hypodermic Injection. Various fistula orifice washing practice. Female Catheterization. Female Bladder Washing. Enema Treatment. Simulator Assembly.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Seeds & Fruits
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall. Size 75×100 cm. Maize seed germination Gram seed germination Bean seed germination Castor seed germination Pea seed germination Dispersal of seeds & fruits Classification of fruits
Reagent Reservoirs
The Universal Reagent Reservoir is a graduated single reagent reservoir with maximum volume of 50 ml, reservoir with 8 separate numbered 5ml.
Reagent channels & a reservoir with 12 separate numbered 5ml. Reagent channels.
Made of polypropylene these reagent reservoirs are repeatedly autoclavable and can be used with all multi-channel pipettes.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Reagent Reservoir 75 ml | 12 |
Linear Expansion Apparatus
Consisting of a metal rod, 500mm in length and 4.5mm diameter, enclosed in a well lagged, nickle plated brass tube with three tubules for steam, inlet, outlet and thermometer.
The metal rod to be studied is supported in the steam jacket by detachable conical cups situated at each end of the tube.
The apparatus is carried on a heavy gauge channel base at one end of which is an adjusting screw.
At the opposite end is a micrometer screw reading to 0.01mm for measuring the expansion.
Supplied complete with copper, brass & iron rods but without thermometer.
Refrigeration Trainer Electrolux Type
This type of refrigeration is usually used for domestic purposes only as it is complex in the construction and working. This type of refrigerator was developed in 1925 by Munters and Battzervan when they were studying at Royal Institute of Technology At Stockholm for their undergraduate course. This type of refrigerator was known as three fluid refrigeration system. The elimination of aqua pump from the absorption system with the complete absence of moving parts and work input. The main purpose of removing the pump was to make the machine noiseless. It uses refrigerant as a solvent s and an inlet gas for inlet of the system. The inert gas is continued to the lower side of system only by its system. It is possible to maintain the uniform pressure throughout the system and after sometime permitting the refrigerant to evaporator at low temperature corresponding to its partial pressure. In the high pressure side system (generator and condenser), there exists only the refrigerant which is subjected to total pressure of the system so that it is condensed by using normal cooling water as air as it is done in other system.
The strong aqua ammonia solution is heated in generator by the application of external heat source. The water vapor carried with ammonia vapor is removed in separate form as shown in figure. Then the dry ammonia vapor is passed into the condenser and it is condensed by using external cooling source. The liquid ammonia flows under gravity in the evaporator and it evaporates. The mixture of hydrogen and ammonia vapor is passed into the absorber and the weak solution from aqua ammonia from the separator is allowed to follow into the absorber, through tray this weak aqua ammonia solution comes into contact with hydrogen separated. This strong solution is further passed to the generator and it completes the cycle.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connection
Rock Cycle Model
Conical Measures
The Conical Measures offered by us are very effectively for measuring small quantities of reagents.
Moulded in Polypropylene, these autoclavable measures have a hexagonal base, which provides it excellent stability.
The measures are clear, have good chemical resistance, and have raised graduation for easy.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Conical Measure 12 ml | 12 | |
| Conical Measure 25 ml | 12 | |
| Conical Measure 50 ml | 12 | |
| Conical Measure 125 ml | 12 | |
| Conical Measure 200 ml | 12 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Vertical Pipette Stand
Our Vertical Pipette Stand imparts features such as Stable, Non-Corrosive, Detachable, etc.
The Vertical Pipette Stand, offered by us, can hold 28 pipettes with maximum diameter of 14mm.
The heavy base measures 225 mm in diameter and a Polpropylene coated square rod measuring 375 mm in length is screwed into the base of the top disc.
This disk can be fixed on the rod, which has holes for holding pipettes while the lower one has pilot holes where the pipette tips rest and liquids drain down to the base.
These discs can be adjusted on the rod according to the length of the pipette.
The arrows provided on the discs should be kept parallel to ensure that corresponding holes are being centered.
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Stand (Verticle) - For 28 Pipettes | 1 |
Human Histology
| Human Skin VS | Human Tongue Anterior Part TS |
| Human Tongue Posterior Part TS | Human Oesophagus TS |
| Human Stomach TS | Human Intestine TS |
| Human Intestine TS | Human Large Intestine TS |
| Human Vermiform Appendix TS | Human Spleen TS |
| Human Liver TS | Human Pancreas TS |
| Human Lung TS | Human Artery TS |
| Human Vein TS | Human Blood Smear |
| Human Trachea TS | Human Epiglottis TS Human Kidney TS |
| Human Bone TS | Human Nerve TS |
| Human Spinal Cord TS | Human Brain Cerebellum TS |
| Human Brain Cerebrum TS | Human Sperm Smear |
| Human Testis TS | Human Ovary TS |
| Human Oviduct TS | Human Mammary Gland TS |
| Human Vagina TS | Human Uterus TS |
| Human Thyroid Gland TS | Human Adrenal Gland TS |
| Human Cardiac Muscle TS | Human Salivary Gland TS |
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
