XTEMOS ELEMENT
AJAX PRODUCTS TABS
Burner Bunsen – Semi Micro
Linear Expansion
Description
Apparatus is fitted on heavy channel base, at one end of which is an adjusting screw, at the opposite end is a micrometer screw reading to 0.01 mm for measuring the expansion. Supplied with one each of aluminium, brass and iron expansion rods but WITHOUT thermometer. Consisting of metal rod 500 mm in length and 4.5 mm dia. enclosed in a well - lagged, metal tube with three tubules for steam inlet, outlet and thermometer. The metal rod to be investigated is supported in the steam jacket by detachable rubber bungs situated at each end of the tube.
Mechanical Heat Pump Trainer
Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.
SPECIFICATIONS:
1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Mini Rotary Shaker
Body made out of thick mild steel finished with powder coating.
PMDC motor used for shaking.
Platform size 300x300 mm. S.S. platform consists of 9x250ml conical flask lotus type clamps.
RPM range 50-250 RPM, Electronic variable control, with 0-60 min mechanical timer.
Mini Rotary Shaker
Workable on 220 V AC 50Hz single phase.
Optional
Digital R.P.M. indicator Digital timer (0-99 min.)
Outside Micrometers Engraved Marking
Description
Micrometer is used to measure short lengths accurately Technical Details : Engraved Marking On The Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finish Frame With Locking Clamp and ratchet stop ; Least Count : 0.01mm/0.001” ; Sizes ; 0-25 ; 25-50 ; 50-75 ; 75-100 ; Specifications Guarantee 6 Months without abuse Packing ; Plastic Box Calibration ; In house.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Calorimeter, Electric
Two Stage Air Compressor Test Rig
The test rig comprises of a two-stage air compressor fitted with an air tank with orifice, pressure gauges 9 an energy meter to measure the input & a Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressures
SPECIFICATIONS:
1.Air compressor – Double cylinder, two-stage type driven by a 2-hp. Three – phase motor mounted on air receiver provided with delivery valve. 2.Air tank and orifice with water manometer for air intake measurement. 3.Pressure gauges at outlet on both stages. 4.Digital temperature indicator. 5.Energy meter to measure input power. 6.A technical manual accompanies the equipments.SERVICES REQUIRED:
1.Floor space of 2,5 X 1.5m. 2.440 V, 15A, 3ph. AC supply with neutral and earthing connection. 3.A hand tachometer.
Three Phase Cyclo Converter
This module is designed for three phase half wave-step down cycloconverter. It consists of 18 Synchronized firing pulses, 18 SCRs, Relevant power supply and circuitry for frequency divisions.
Specification
• Eightin nos. SCR with RC snubber protection is provided for 3phase • cycloconverter power circuit (each phase consist of 6 SCRs) Rated at 1200V@25Amps. • Three nos. center tapped inductor (0%.50%, 100%) is provided for power circuit. • Eightin nos. Isolated gate pulses for SCR power circuit. • One potentiometer is provided to vary the frequency. • One potentiometer is provided to vary the output voltage. • MCB protection. • Housed in sleek screen printer cabinet. • Provision for V/F control Power Supply. • Input 440V ± 10%, 50HZ three phase AC supply. • ± 15V DC, 9V, 9V, 9V AC (3phase) for the firing circuits. • 24-0-24V 3phase input for power circuit.
Multi Process Trainer
Features
• Pressure transmitter mounted at the bottom of the process tank • Flow transmitter (DPT) with rotameter mounted across the pipe line to sense the flow of water • Temperature sensor of (RTD) type mounted at the outlet of the heater • An industrial type heater as a heat source • FHP pump for water Circulation • SS Storage tank of 15 liters Capacity • Power driver provided to vary the pump speed and Heater Power. • Orifice plate is used for pressure drop measurement. • An electronic signal conditioner is provided. • Bourdon tube pressure gauge is provided to measure the tank. • Latest power driver is used to drive the pump & heater. • USB/Serial port data acquisition is provided.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Hall Probe
Ge single crystal with four spring-type pressure contacts is mounted on the printed circuit board. Four leads are provided for connections with measuring devices.A zero setting can be done by adjusting the spring contacts with the help of screw driver.
Specifications:
Material: Ge single crystal, n type
Resistivity: 8 – 10 ?-cm
Contacts: Spring type
Model of Terrestrial Telescope
Rotary Compressor Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Resistance Box
Description
Resistance Box kit is an excellent device, which provides a very good learning technique in making different combinations of resistances, either in series or in parallel or in both ways to obtain the desired value of resistance for any circuit application. It consists of 10 resistors of equal values, i.e., 10Ω , 2 watts. These resistances are of ± 1% tolerance
Survey Chain
Pulley Bench Clamp Fitting
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Autoclaves / Pressure Steam Sterilizers Superior
Specification
Superior quality & finish. All these autoclaves are made of 8 gauge aluminum. The drum is deep drawn. The lid is die casted. Locking of lid by 6 nuts with rubber gasket seal in between (no metal to metal seal). Two safety valves, pressure gauge, flexible metal tubing to exhaust air. Includes outer stand, inner tripod stand.Features
Equipped with two stages "over pressure" protection system incorporating a calibrated continuous bleeding Pressure stopcock and pressure release weight valve.Pressure Gauge
Colour coded pressure gauge showing internal chamber conditions during the cycle. Sterilization zone in green colour is shown from 15 psi to 20 psi (or 1.034 bar to 1.378 bar) which is equivalent to temperature of 121°c to 127°c. Dial size : 2.5". Dial show measurement in 2 units. (i) kg/cm2 (ii) lb/inch2 Full scale dial of pressure gauge is 0-30 lb/ inch2 or 0-2 kg/cm2 Caution zone in red colour. Equipped with steam release /control valve and flexible metal exhaust tube.| Capacity (Lt.) | Power | Size | Type |
|---|---|---|---|
| 21 Ltr | Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 21 Ltr | Non Electric | 300 x 300mm = 12” x 12” | Mirror Finish |
| 27 Ltr | Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 27 Ltr | Non Electric | 300 x 380mm = 12” x 15” | Mirror Finish |
| 37 Ltr | Electric | 350 x 380mm = 14"x15" | Mirror Finish |
| 37 Ltr | Non Electric | 350 x 380mm = 14"x15" | Mirror Finish |
Insect Storage Box
Description
For pinning of insects both inside top & bottom, White hardwood / Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with 8mm thick soft pinning. washable EVA sheet. Inside glazed white. Raised wall with holes for insecticide inside bottom to make box air tight and pest proof. Fitted with brass hinges. index card holder & clips. Insect Storage BoxSize 53x45x9 cm Insect Storage BoxSize 45x30x7.5 cm Insect Storage BoxSize 38x25x7.5 cm Insect Storage BoxSize 30x23x7.5 cm
Ripple Tank
Description :-
Transparent acrylic plastic ripple tank, supported in a sturdy plastic frame which has recesses to hold four legs with leveling feet.
The tank edges are shaped to minimize undesired reflections.
Tank has a drain hole closed by a rubber stopper.
With two light alloy uprights to carry a horizontal rippler support rod which is adjustable for height.
The ripple assembly, elastically suspended from the support rod, consists of a 4 – 6 V DC motor mounted on a wooden beam.
The motor has an eccentric weight which causes the beam to oscillate.
Two point sources are provided by two plastic spheres, each mounted on a right angle rod.
A metal rod is fixed centrally into a socket in one short side of the frame to afford support to the illuminant.
Overall size of the tank 580 x 500 x 80 mm, window area 370 x 280 mm, height of tank above bench level (with legs attached) approx. 375 mm.
Complete with following accessories :-
1. Two straight obstacles of aluminium alloy length 130 mm.
2. One straight obstacle length 40 mm.
3. One curved reflector radius 200 mm.
4. One trapezoidal plastic plate for refraction.
5. One wood hand wave roller.
6. One water dropper.
7. One pkt. rubber bands.
8. One foam plastic sponge.
9.One illuminant with a 12 V, 24 W lamp mounted in a lamp house and provided with a long supporting rod.
