XTEMOS ELEMENT
AJAX PRODUCTS TABS
Motor With Solar Cell
Mock Layout Of Car Wiring Latest Type
Mock Layout Of Car Wiring Latest Type
All the components used in the apparatus are of modern car. The complete mock layout is beautifully divided into 5 sections as under
(A) Front Lighting Panel
(B) Dash Board Panel
(C) Ignition System
(D) Rear Lighting Panel
(E) Motorised Charging System
With the help of this mock layout system its becomes very easy for the students to understand the actual working of electrical system of a modern car.
Latent Heat of Steam Apparatus
Falling Body Apparatus
L-Section launcher with holes for locating two 19mm.
diameter steel balls which act as projectiles.
Launcher is released by push button and projects one ball forward while allowing the other to fall freely Launching mechanism mounted on wooden block, 180x60x30mm.
which may be clamped by bench and has a convenient storage pocket for the balls.
Complete with two steel balls.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
CNC Lathe Trainer2
CONTROLLER:
SIEMENS / FANUC Main Spindle Drive : AC Motor with VFC Z and X Drives : Stepper drive with Servo Motor Input to Servo : Optically lsolated Motor Drive : Smart & Intelligent Run Speed Control : Through Controller Interpolation : Linear/Circular /parabolic Cycles Used : G, M, S, T, F, I, K, M, F, Circular interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuit and over Temperature Protected, Single Phase Protection Real Time Toolpath Simulation : ProvidedMACHINE DETAILS:
Center Height : 150mm Swing over Carriage : 125mm Distance between Centre : 825mm Weight : 1100kg Dimension in mm : 2000 x 1200 x 1700 Rapid Travel : 5000mm/min Resolution Z Axis : 1 micron Resolution X Axis : 1 micron (Dia.) Automatic Lubrication : Provided Tool Changer : Automatic – 4 station SPINDLE Spindle Speed : Continuous Variable Spindle power : 3 HP Inside Taper : MT4 Speed Range : 50 to 1800 RPMAXIS TRAVEL:
X Axos : 120mm Z Axis : 800mm
Elastically Coupled Beam Apparatus
Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the centre of another elastic beam supported at two outer ends only. Mild steel Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Histology (Shark)
Polarising Filter Stress Determination
Description
Demonstrate stress patterns in solids with this new and valuable equipment. Two polarising filters, mounted on a graduated frame are placed on a plastic base. Clear acrylic pieces of different shapes are introduced between the filters; when pressure is applied to the solids the resulting stress patterns are observed. An important method of demonstrating polarisation and stress. Includes instructions.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Digital Colorimeter
Description
The basic set-up of the colorimeter is: LED light source: Produces polychromatic light over the entire visible region, 45 Broad spectrum filter: The colorwheel has nine different filters. The filter employed is selected by wavelength. Each filter will produce monochromatic light at a specified peak wavelength with a bandpass of 20 mm. The filters enable the user to perform tests from 400 to 680 nm. Cuvette Holder: It holds the inserted cuvette during testing. It is imperative the cuvette be consistently oriented in the holder. Round cells usually have orientation markings to correctly position the cuvette. Detector: A silicon photo diode is used as the detector. The photo detector current will change as a function of light energy. Display:The current signal from the detector is converted to a numerical value, absorbance and is shown on led display
8085 Microprocessor LC LCD Trainer
Specification
• Intel 8085A CPU @ 6.144 MHz Clock speed. • RAM : 8KB expandable upto 32KB, Jumper selectable. • EPROM : 8KB expandable upto 32KB, Jumper selectable. • Lithium Battery Back up for RAM • PC Keyboard (104Keys) • 16x2 Alphanumeric Dot Matrix Liquid crystal display with back light • 3 Channel 16 Bit counter / timer terminated in a 10 pin connector using 8253 • 24/22 TTL I/O lines, terminated at 1 No of 26-Pin FRC connector by using 1 No of 8255/1No 8155 respectively • 8 Nos of Digital inputs terminated and given through on board 8 way Dip switch • 8 Nos of Digital outputs are terminated and displayed in the 8 Nos of SMD type LEDs • Digital I/O lines are terminated in 20-Pin connector • RS 232C compatible Serial port terminated in a 9-pin 'D' male connector • One VXT-Bus (50-Pin FRC Connector) for interfacing VBMB series of experiment boards for bus expansion. • Interrupts are terminated in a 5-Pin connector • Built in Line Assembler and Disassembler provided. • Software single stepping of user programs by instruction for software debugging.
Complete Optical Bench Set
Description
The Complete Optical Bench Set is an economical alternative to conventional optical benches that provides accurate demonstrations of basic optics principles. The complete system includes: 1. Optical bench-double-sided meter stick. 2. One Object and Marker. 3. One Screen support. 4. One Candle holder. 5. One Pair of metal supports. 6. Two Lens supports— 4 cm and 7.5 cm. 7. Five White board screens, each 10 x 12.5 cm with a millimeter scale along one side. 8. 12 paraffin candles.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Young’s Moduluds Appratus
Comprises a scale plate carrying a 0 to 30 mm scale, and a moveable vernier readable to 0.1 mm.
Both have bars with clamping screws for the wires and hooks for the tension weight and loading masses.Supplied with clamp for fitting.
A tension weight, mass 1.3 kg approx. for the comparison wire is also included.
Complete with load masses and wires.
Masses Aluminium
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
Linear Air Track
Angular section aluminium alloy track, length 255cms, with staggered air holes, supported on two light alloy castings positioned 45 cm from each end of the track.
One support has a two- point contact and other one-point contact for lateral and horizontal adjustments for which a knurled screw is provided.
Large catapult arms with slots for elastic bands are fitted to each end of the track.
A fully fitted to one end of the track enables experiments involving acceleration under a constant force.
Identical end caps enable air to be introduced from either end of the track, bung being supplied to close the end not being used.
The vehicle buffer attachments and clamping screws are matt black to help interpretation of stroboscopic photographs.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Steam Power Plant Trainer
Introduction:
Steam Power Plant Working Unit – This Unit Helps The Students To Understand The Complete System Of A Thermal Power Plat. 1.Heat Energy Converts Water Into Steam 2.Steam Pressure When Moves A Engine Or Turbine Produces Mechanical Energy 3.Finally Mechanical Energy Is Converted Into Electricity Through AlternatorParts Details Of Boiler:
1.Boiler — For The Generation Of Steam We Have Provided Electrically Heated Boiler. 2.Diameter Of Boiler – 400 mm 3.Length Of Boiler – 600 mm 4.Heater 2 Pcs. – 3 KW (Each)
Fuel Supply System Of A 4 Cylinder Diesel Engine
Drilling Tool Dynamometers
This is a armed wheel type strain gauge drill tool dynamometer designed to measure thrust and torque during drilling operation. This Dynamometer is suitable for drilling a hole up to 25mm size in mild steel. With this Dynamometer students can study the change in these force by varying speed, cut and feed
FEATURES:
1.Rigid in construction & Sensitive transuding and amplifying system for accuracy in force measurement. 2.Compact two channel digital force indicator. 3.Use of cutting fluid during operation is possibleSCOPE OF SUPPLY:
1.Mechanical sensing unit and work piece holder with strain gauges. 2.Control panel housing digital force indicator to measure both forces simultaneously, balancing potentiometer, connoting cables. 3.Necessary switches, fuses and screen printed front plate. 4.The dynamometer is calibrated at factory with help of proving ring and readings are directly in the from of kg.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Reynold S Apparatus
DESCRIPTION:-
The Set-up is designed to verify Reynold’s Apparatus experimentally. The Apparatus consists of a glass tube which one end having bell mouth entrance connected to a water tank. At the other end of the glass tube a cock is provided to vary the rate of flow. Flow rate of water can be measured with the help of Measuring Cylinder and Stop Watch, supplied with the set-up. A capillary tube is introduced centrally in the bell mouth. To this tube dye is fed from a small container, placed at the top of Constant head Tank, through polythene tubing.EXPERIMENTS:-
Ø To study different types of flow. Ø To determine the Reynold’s Number and hence the type of floe either laminar or turbulent.UTILITIES REQUIRED: -
Ø Water Supply. Ø DrainTECHNICAL SPECIFICATION: - | ||
| Ø Tube | : | Material Borosilicate Glass |
| Ø Dye Vessel | : | Material SS, Suitable Capacity |
| Ø Capillary Tube | : | Material Copper/Stainless Steel |
| Ø Constant Head Water Tank | : | Capacity 40 Liters. |
| Ø Water Circulation | : | FHP Pump |
| Ø Flow Measurement | : | Using Measuring Cylinder |
| Ø Sump Tank | : | Capacity 60 Liters |
| Ø Stop Watch | : | Capacity 60 Liters. Electronic |
| Ø Control Panel Comprises of | : | Standard make, On/Off Switch, Mains Indicator, etc. |
| Ø The Whole set-up is well designed and arranged in a good quality painted structure. | ||
Study Of Flow Measurement Devices
Measurement of liquid flow is required at various places and for various purposes. Different types of flow measuring devices are used depending upon the system conditions, accuracy required, skill of operator and economy desired. The unit demonstrates some of the flow measurement devices.
SPECIFICATIONS:
[1] Intergratiry Type Turbine flow meter. [2] Glass Tube Rotameter. [3] Orificemeter differential manometer. [4] Venturimeter [5] Measuring Tank [6] Stop Watch (Digital) [7] 112 HP Monoblock Pump. [8] A differential manometer. [9] Sump tank of suitable capacity. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC.Power Supply
