XTEMOS ELEMENT
AJAX PRODUCTS TABS
Dissecting Trays
Adjustable Tuning Fork
Level Control Measurement Module
This module consists of a process tank with a miniature pump, level sensor for 2 levels, a power supply, etc., To establish a ON/OFF control for the level of water. Circuitry is provided for stand alone operation or through a 8255 port of a Microprocessor kit.
Specification
• A transparent tank of height 150mm with adjustable electrodes to vary the high level and low level. • A pump with tank for water circulation • Water level can be monitored under software control/automatic mode • One power relay 230V/6Amp for pump ON/OFF control • Miniature connectors are provided to operate as stand alone controller or through software under a Microprocessor trainer. • Built in power supply.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Lagged Pipe Apparatus
Lagged Pipe Apparatus:
The apparatus consists of three concentric pipes mounted on suitable stand. The space between innermost and the middle pipe is fifed with a lagging material and the space between the middle and the outer most is filled with and other lagging material. The lagged pipe is heated with a cartridge heater inserted at the axle length of the pipe. Voltmeter and ammeter on the panel can measure the input to the heater. The intermediate temperatures can be measured by the thermocouples attached at the surfaces of the pipe. Thus the resultant conductivity of the materials can be found out.
SPECIFICATIONS:
1.Pipes : a)Gl pipe (innermost) – 6 cm. (Outer Diameter). b) Gl Pipe (Middle) – 8.5 cm. (Mean Diameter) c)G! Pipe (Outermost) – 10.7 cm. (inner Diameter) d)Length of pipes 1 Meter. 2.Heater : Nichrome wire cartridge heater placed centrally, of suitable capacity. 3.Control Panel : a)Single Phase Dimmerstat – 1 No. b)Voltmeter (0 – 250V) – 1 No. c)Ammeter (0- 2A) – 1 No. 4.Temperature Indicator : Multichannel Digital Temperature Indicator ranging (0 – 300 C) using Cr/AI ThermocouplesServices Required:
1. A.C. Single Phase 230 V electric supply 2. Floor Area-1.5 Meter X 1 Meter X 0.5 Meter High
Porcelain Combustion Boat
Description
We offer Porcelain Combustion Boats all around the world. These Porcelain Combustion Boats are made available in varied specifications and grades. Besides, our Unglazed Porcelain Combustion Boat is highly demanded in European, Asian and other markets for its quality and diverse laboratory applications.| Capacity (ml) | Height (mm) | Width (mm) | Length (mm) | |
|---|---|---|---|---|
| -- | 10 | 12 | 80 | |
| -- | 11 | 13 | 86 | |
| -- | 11 | 13 | 90 | |
| -- | 11 | 13 | 120 |
Annelida
Earthworm Buccal Region TS
Earthworm Pharynx Region TS
Earthworm Spermathica Region TS
Earthworm Oesophagus Region TS
Earthworm Seminal Vesicle Region TS
Earthworm Prostate Gland Region TS
Earthworm Testis Region TS
Earthworm Intestinal Region TS
Earthworm Gizard Region TS
Earthworm Clitellum Region TS
Earthworm Typhlosolar Region TS
Earthworm Anterior Region Sag. Sec.
Earthworm Ovary WM
Earthworm Setae WM
Earthworm Septal Nephridium WM
Nereis Parapodium WM
Heteronereis Parapodium WM
Nereis Body TS
Leech Crop Region TS
Leech Stomach Region TS
Leech Intestinal Region TS
Leech post. Sucker TS
Leech Ant. Sucker TS
Ray box Multi Slit
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Digital Coating Thickness Meter
Description
Digital Coating Thickness Meter We offer high quality of Digital Coating Thickness Gauge. Statistics (Number of readings, average, Std. deviation, max. ,; min.) are updated with every reading and displayed simultaneously. It helps to decide how many readings are to be taken. Continue taking readings till you start getting reasonably consistent statistics.
Porcelain Crucible
Description
Porcelain Bottom Crucible with porous disc permanently formed into walls. Porcelain Crucible, which we offer, is featured by stable porosity and rate of flow. These Porcelain Crucibles are made available with very fine (1.2 micron), fine (5 micron) and medium (15 micron) pore diameters discs. Maximum operating temperatures for Porcelain Bottom Crucible range from 900Â °C to 1200Â °C depending upon ceramic composition selected. Further, variation in temperature will not affect characteristics within their working temperature range.Capacity
15 ml 25 ml 30 ml 50 ml
Cyclone IV FPGA Controller
FEATURES:
• Based on Altera family Cyclone IV, Device : EP4CE30 • One 34 pin header used for IPM Interface. - 16 PWM output - 8 capture inputs. • One 26 pin header ADC. - 4 channel 1MSPS ADC. - Total 8 channel using 2 Nos of ADC. - 12 bit resolution. - Input range -10V to 10V / -5V to 5V. • One 5 pin phoenix connector DAC - 4 channel DAC, 12 bit resolution. - Output range -10V to 10V / -5V to 5V. • 8 output Light Emitting Diodes (LEDs). • 8 input slide Switches. • 4 user push button switches. • 2-user limit switch. • 20 x 4 Alphanumeric LCD display. • On Board Isolated JTAG Programmer Compatible with QuartusII software. • Isolated USB (USB to Serial) interface. • 3 Nos of 20 pin header each have 16 IOs.
HISTOLOGY
These three sets build up to a complete study of mammalian histology.
Basic histology is covered by Histology set I.
The addition of Histology sets II and III gives a comprehensive collection of histology microslides, which should meet the needs of most advanced courses.
No teaching notes are supplied with these sets.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Brush, Cylinder
Polishing Pan
Dynamic Trolley, Wooden
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Refrigeration And Air Conditioning Components
Actual Cut Section – Display Board (Set Of 30)
This actual cut section model is a set of thirty components used in refrigeration & air conditioning. With the help of this model students can understand the working parts of the components used in refrigeration & air conditioning. This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Episiotomy Training Simulator
Description
Suturing Simulators provide a realistic way for students to learn good surgical techniques. The simulators provide students with a variety of repair experiences without the constraint of time and concern for safety, which are factors with a live patient. The simulators can be used by the student in a learning lab with an instructor or by the student individually in the clinical setting just prior to a patient experience. They are also useful as homework teaching aids that can be signed out at night and returned the next day. In addition to being portable, the lifelike texture allows the learner to develop a “feel” for instrument handling, tension on suture, and the advantages of one method of tying knots over another.Includes one of each simulator:
Midline Suture Simulator Left Mediolateral Suture Simulator Right Mediolateral Suture Simulator Each simulator comes with an instruction booklet and is individually boxed.
Calorimeter copper
Micro Convavity Slides
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Single Phase Cyclo Converter
Specification
• Consists of firing circuit, SCR power circuit and load. • Line synchronized IC based linear firing circuit. • Line synchronization achieved by step - down transformer. • Four nos. firing pulse with pulse transformer isolation to trigger four SCR. • One no. potentiometer used to vary the firing angle (180° - 0°). • Carrier logic implemented with carrier frequency of 4KHz. • One no. toggle switch with debounceogic for pulse ON/OFF. • EPROM Based firing pulse frequency variation. • Two nos. toggle switch to select different frequency (Hz, 50/2Hz, 50/3Hz, 50/4Hz). • Power circuit consists of Four nos. SCR with fuse protection. • Anode, Cathode, Gate terminals are terminated in the front panel for user connection. • 24V AC, 1Amp Provided for power circuit input with ON/OFF switch. • One no. fixed R, load provided Center tapped inductor for power circuit. • 230V, 50Hz AC input with ON/OFF rocker switch, fuse for over load.
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
Sliding Mesh Gear Box
Sliding Mesh Gear Box – Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Pelton Wheel Turbine Test Setup
DESCRIPTION:
Pelton Wheel Turbine is only impulse water turbine now in common use named in honor of Sir L.A. Pelton (1829-1908) of California, USA. It is a tangential flow impulse turbine. The water strikes the buckets along the tangent of the runner. The energy available at the Inlet of the Turbine is only kinetic energy. The Pressure at the Inlet and Outlet of the atmospheric. This turbine is used for high heads. The Present Set-up consists of a runner. The buckets are mounted on the runner. The water is fed to the turbine, through SS nozzle with a SS spear, by means of Centrifugal Pump, tangentially to the runner. Row of water into turbine is regulated by adjusting the spear position by the help of a given hand wheel the runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. The circular window of the turbine casing is providing with a transparent acrylic sheet for observation of flow on to the buckets. This runner assembly is supported by rigid MS structure. Load is applied to the turbine with the help of this brake dynamometer so that the efficiency of the turbine can be calculated. Pressure Gauge is fitted at the Inlet of the turbine to measure the total supply head to the turbine.EXPERIMENT:
1.To study the operation of a Pelton Wheel Turbine 2.To determine the Output Power of Pelton Wheel Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 111 (1.33 HP) | HM 111 (2 HP) | HM 111 (5 HP) |
| Output Power | 1.33 HP / 1 Kw | 2 HP / 1.5 Kw | 5 HP / 3.75 Kw |
| Discharge | 300 LPM (Approx.) | 400 LPM (Approx.) | 630 LPM (Approx.) |
| Supply Head | 25 m | 40 m | 45 m |
| Rope Brake Dynamometer | Dia 200 mm | Dia 200 mm | Dia 300 mm |
| Sump Tank | Capacity 150 Liters. | Capacity 200 Liters. | Capacity 300 Liters. |
| Water Circulation Centrifugal Pump | Capacity 5 HP, Three Phase | Capacity 7.5 HP, Three Phase | Capacity 15 HP, Three Phase |
| Speed | 1000 RPM (approx.) | ||
| Impeller | Material Brass, Bucket type | ||
| Nozzle | Material Stainless Steel/Mild Steel | ||
| Spear | Material Stainless Steel/Mild Steel | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
