XTEMOS ELEMENT
AJAX PRODUCTS TABS
Insect Storage Box
Description
For pinning of insects both inside top & bottom, White hardwood / Teakwood frame with melamine lamination on top & MDF sheet bottom is nicely polished. Top & bottom lined with 8mm thick soft pinning. washable EVA sheet. Inside glazed white. Raised wall with holes for insecticide inside bottom to make box air tight and pest proof. Fitted with brass hinges. index card holder & clips. Insect Storage BoxSize 53x45x9 cm Insect Storage BoxSize 45x30x7.5 cm Insect Storage BoxSize 38x25x7.5 cm Insect Storage BoxSize 30x23x7.5 cm
Bi Metallic Strip
Ocean Features Model
IPM Based Power Module
Power Module is designed for Motor control Applications upto 3 HP by using IGBT & DIODE Technology Based IPM. Input:1 Phase / 3 phase 50 Hz AC. Output : 400V/10A (MAX), AC/DC on each Leg of 3 phase Bridge
FEATURES:
• 1200V, 25A, 3 Phase IGBT Inverter Bridge • 1200V, 10A IGBT for Over Voltage breaking • Built - in Over Voltage, Under Voltage, Over Current & Over Temperature ProtectionADDITIONAL FEATURES:
• 1200V, 25A Converter Bridge for AC-DC power conversion • 4 Nos of Hall Effect current sensors are provided to sense the DC Link current & 3 output current of the Inverter Bridge • 1 No of Hall Effect Voltage sensor is provided to sense DC Link voltage • All the PWM signals are isolated using Opto Isolator • Protection circuit for over current with LED indication • Optically Isolated Fault signal from the IPM is given to the Embedded/DSP controllers for protection. • Independent Power supplies for all Isolated circuits. • 0-900V Voltmeter is provided to Indicate the DC Link Voltage • All current, PWMS & Feedbacks are terminated at Front panel • FRC Connectors are provided to Interface with the Embedded/DSP controllers • All the Input/output Lines are terminated at Banana sockets.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Pregnancy Pelvis With Baby
CONDENSER CLAMP
PRODUCT DESCRIPTION
- Three finger condenser extension clamp with Bose head.
- Aluminum stem the overall length of the clamp is 10.0.
- The extension rod contributing 6 the rubber coated jaws will open to 3.5 and will provide a six point contact for a firm
- The boss head right angle clamp will accept rods up to.63 /16 mm.
- 3 Finger Aluminium Condenser Clamp (Rubber Lined)
- 4 Finger Aluminium Condenser Clamp (Cork Lined)
- 3 Finger Brass C.P. Condenser Clamp (Cork Lined)
- 4 Finger Brass C.P. Condenser Clamp (Cork Lined)
Coil Ignition System Of An Automobile
Resistance Units
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Electronic Total Station
Cryovial
Cryovial are normally used for storage of Biological material, human & animal cells.
These sterilized tubes are provided with white prominent graduation and a long marking area for sample identification.
The cap of these Cryovial is provided with a seal ring inside to make it completely leak proof.
The longitudinal grooves in the base give a non-twisting feature to these vials when paced in a cryo rack.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Vail - Internal Thread 2.0 ml | 500 | |
| Cryo Vail 1.8 ml | 1000 | |
| Cryo Vail 4.5 ml | 500 |
Hydraulic Bench Apparatus
OBJECTIVE:
To conduct the experiment of hydraulic bench, with separate experiential set ups i.e. Hydrostatic Pressure, Flow over Weirs, Bernoulli’s Theorem, Flow meter Demonstration, Impact of jet and Orifice Discharge etc. which are accessories of the Hydraulic Bench.DESCRIPTION OF APPARATUS:
The set up is a self-contained, water recirculation unit provided with a top tray, sump tank and a measuring tank. Drain valve and over-flow are provided on the sump tank. A centrifugal pump is fitted for water circulation. Flow control valve and bypass valve is fitted in water line to conduct the experiment at different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch. Measuring tank is provided to measure the discharge. Drain valve is provided in the measuring tank to empty water in sump tank after measuring discharge. Separate level indicator and scale is provided to read the level of water in the measuring tank.UTILITIES REQUIRED:
1.Water Supply (Fill approx 250 Ltrs Initially). 2.Drain Required. 3.220 V AC, 50 Hz, single phase electric supply source. 4.Floor area 1.75 m x 1.50 m.SPECFICATION:
1. Top Tray : 1060 mm x 650 mm. 2.Pump : 1 HP 3.Flow Measurement : Using measuring Tank (Material SS) 4.Tank : Capacity 40 Ltr. 5.Sump Tank : Capacity 120 Ltr. Material SS. The whole set-up is well designed and arranged in a good quality powder coating painted structure.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Amplitude Modulation And Demodulation
Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission. It is still used in radio system to transmit audio signal although it has lesser in popularity compared to FM (Frequency Modulation) due to its lower signal to noise ratio.
Technical Specification :-
1. I C based DC regulated Power Supply ±12 V / 500 mA.
2. Audio frequency 1 KHz / 0-2 Vpp for modulating signal 455 KHz / 2.5 Vpp approx. for Carrier Frequency.
Steering Geometry Wheel Alignment Trainer
Steering Geometry & Wheel Alignment Trainer
With the help of this trainer the students can learn about steering geometry and practically perform wheel alignment using various tools.
(A) Turn Tables
(B) Toe In Toe Out Gauge
(C) Magnatic Caster Camber Gauge
(D) Manual Steering System With Four Wheels
(E) Tool Kit
Light Reflection and Refraction Set
Description
This optical kit helps students easily study these two important wave properties: Reflection and Refraction. Set made up of a wooden and rotating platform. base triangular stand made up of a disc and a rotating arm. The rotating platform provides a high degree of accuracy when making measurements as well as provides an easy way to change angles without disturbing the light source.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Torsion Of Rods Apparatus
INTRODUCTION:
A torsion test is quite instrumental in determining the value of modulus of rigidity of a metallic specimen. The value of modulus of rigidity can be found out thought observations made during the experiment by using the torsion equation.APPARATUS:
1. A torsion testing machine. 2. Twist meter for measuring angles of twist 3. A steel rule and Vernier Caliper or micrometer
Karl Fisher Titrimeter
Description
Auto Karl Fischer Titrimeter – 761 is an automatic apparatus designed to carry out Karl Fischer Titrations for accurate determination of moisture content in various samples. The instrument comprises of two units i.e CONTOL UNIT & TITRATION UNIT. The CONTROL UNIT controls the complete automatic titration. On pressing the START button, the titration starts and the KF reagent is added automatically from the burette, through a solenoid valve into the titration vessel. As soon as the end point is reached, the titration is stopped automatically by the Control Unit. It has fully solid state circuitry incorporating advanced IC technology. Titration unit contains the magnetic stirring mechanism and the solenoid valve assembly. The cabinet is designed to serve as a titration stand. Karl Fischer method for determination of moisture content is used in pharmaceutical and drug manufacturing industries, food stuff, sugar, wood, paper and textile industries, petroleum refineries, chemical and fertilizer units etc.
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height [2] Orifice – 8mm and 10 mm. [3] Mouthpiece (a) LID = 4 (b) L/D = 1 (c) Bordas mouthpiece. (d) Convergent mouthpiece. [4] X-Y gauge for orifice jet co-ordinates. [5] Measuring tank of suitable capacity OR a calibrated water flow meter. [6] Sump tank of suitable capacity. [7] 0.5 HP pump with valve. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Whirling Of Shaft Apparatus
The unit consists of a main spindle driven by a variable speed motor. Three different governor assemblies can be mounted over the spindle. A with pointer measures the lift of the governor. Students can calculate characteristics of governor at and compare their performance viz. Sensitiveness, stability, governor effort etc.
SPECIFICATIONS OF WHIRLING OF SHAFT APPARATUS:
1.Governor assemblies – Hartnell, porter & propel governor assembly one each with rotating weights. 2.Variable speed FHP D.C. motor to drive the main spindle. 3.Sliding weights for porter & proell governor. 4.Scale & a pointer to measure governor lift. 5.Spring & Spring compression adjustment arrangement. 6.A technical manual accompanies the unit.SERVICES REQUIRE FOR WHIRLING OF SHAFT APPARATUS:
1.230V, 5A, AC supply connection. 2.Bench area of 0. 75 x 1m. at working height.
Multi Stage Centrifugal Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Multi Stage Centrifugal Pump. The Set-up consists of a Multi Stage Centrifugal Pump coupled with DC motor & drive, supply tank, measuring tank & pipe fittings for closed loop water circulation. There are 2 separate pumps connected to DC Motor and drive and can be connected in series and parallel to stimulate different combinations. Pressure and Vacuum Gauge are connected on delivery and suction side of each pump for the purpose of measurement. Swinging Field Dynamometer arrangement for direct torque measurement using dial type spring balance is made for individual pump. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENTS:
1.Speed Vs Discharge 2.Head Vs Discharge at various speeds 3.Efficiency curves at various speed and headsFEATURES:
1.Closed loop water circulation 2.Compact & stand alone set-up 3.MS Excel sample calculation program on demand 4.Stainless Steel tanks and wetted parts 5.Superb painted structure 6.Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC), 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½” BSP. Distilled water @ 80 Ltrs. (Optional extra cost)TECHNICAL SPECIFICATIONS:
1.Pump (2 Nos.) : Kirloskar, Capacity 1 HP Speed 2800 RPM (max.) Head 12 m (max.) 2.Drive : DC Drive along with non-contact type Digital RPM Indicator 3.Supply Tank : Capacity 150 Ltrs. 4.Measuring Tank : Capacity 100 Ltrs. fitted with Piezometer Tube & Scale 5.Piping : GI / PVC 6.Stop Watch : Electronic 7.Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structure.
SCR VI Characteristics Study Trainer
Specification
• Basic VI characteristics study trainer. • Consists of one no. TYN612 SCR with heat sink. • LM723 based 20V DC power supply for gate voltage. • One no. potentiometer used to vary the gate current • 0- 30V DC variable power supply for anode, cathode voltage variation. • One no. potentiometer used to vary the Vak. • One no. high voltage fixed load resistor. • One no. toggle switch to ON/OFF gate voltage. • Two nos. DC ammeter, voltmeter/multimeter provided to measure Ig&Vak, Ia. • 230V AC input. Power ON/OFF switch. • All components are mounted on a screen printed PCB fixed on a nice wooden cabinets.
Platyhelminthes
Planaria Body TS
Liver Fluke WM
Liver Fluke TS Middle Region
Liver Fluke TS Gonad Region
Liver Fluke TS Proboscis
Liver Fluke TS Post Region
Liver Fluke TS Post Sucker
Liver Fluke Cercaria WM
Liver Fluke Metacercaria WM
Liver Fluke Redia WM
Liver Fluke Sporocyst WM
Liver Fluke Miracidium WM
Tape Worm Scolex WM
Tape Worm Proglottid Immature TS, WM
Tape Worm Proglottid gravid TS, WM
Tape Worm Proglottid mature TS, WM
Tape Worm TS
Free Force Vortex Apparatus
DESCRIPTION:-
The experimental set up consist of a circular transparent cylindrical tank in which four circumferential jets have been placed along the circumference of the cylinder near its bottom which helps in the formation of free vortex. It is assumed that the torque exerted by these jets is negligible. The Orifice is reducing bush so that a reduced diameter can be investigated. The plate can also be rotated with the help of a variable speed motor so that the cylinder rotates about its vertical Axis with the help of a V belt and forced vortex is formed. Conditions wear allowed to steady state and the depth of flow at any particular point was observed not to change over a period of time. The experimental procedure involves measurement of resulting free surface that represents the variation of the sum of the pressure and datum head.SCOPE OF EXPERIMENTS:-
Ø To plot the surface profile of a free and forced vortex by measurement of the surface profile coordinates and to show that total energy is constant throughout vortex.TECHNICAL SPECIFICATION: –
Ø Cylinder : Material Acrylic Dia. 200mm approx Ø Height of Overflow point : 150mm Ø Drive : FHP variable speed motor, speed way Ø The whole Set-up is well designed and arranged in a good quality painted Structure
