XTEMOS ELEMENT
AJAX PRODUCTS TABS
Steam Power Plant Trainer
Introduction:
Steam Power Plant Working Unit – This Unit Helps The Students To Understand The Complete System Of A Thermal Power Plat. 1.Heat Energy Converts Water Into Steam 2.Steam Pressure When Moves A Engine Or Turbine Produces Mechanical Energy 3.Finally Mechanical Energy Is Converted Into Electricity Through AlternatorParts Details Of Boiler:
1.Boiler — For The Generation Of Steam We Have Provided Electrically Heated Boiler. 2.Diameter Of Boiler – 400 mm 3.Length Of Boiler – 600 mm 4.Heater 2 Pcs. – 3 KW (Each)
Pilot Static Tube Set Up
DESCRIPTION:-
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper / SS is supplied and is fixed below Vernier scale. The Vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube Ø To plot velocity profile across the cross section of pipeUTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pitot Tube : Material Copper/SS of compatible size fitted with Vernier Scale Ø Test Section : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 40 Ltrs. Ø Sump Tank : Capacity 70 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Differential Gear Assembly Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Typical Flower
Hook’s Law Apparatus
Balance Spring
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Shunt Active Filter Trainer
Specification
• FPGA Spartan 3A DSP board used for generating the PWM signals. • Three phase 3 level diode clamped inverter used as a Active filter. • SRF (or) Instantaneous PQ theory will be used to generating reference current. • PI control or fuzzy logic will be used to regulate the dc link capacitor voltage. • Reference DC link Voltage will be 250V. • Hall effect current transducers used to sense the source currents, load currents and compensation currents. • Hall effect voltage transducers used to sense the dc link voltage and source voltages. • Necessary source inductor and filter inductor provided. • Input source Line voltage -200V (Peak). • Input source Current -10A (Peak). • Power Rating -3KW. • Reactive power compensation can be provided. • 3KW linear and non-linear loads will be given. • User can modify source, filter inductance and external loads. • User can modify control algorithm. • Industrial type cabinet provided. • Before compensation source current THD will be greater than 26% • After compensation source current THD - 2.5 - 4% in 3 level inverter - 4 - 5% in 2 level inverterXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Mirror, with Base
Human Eye, 3 Times Enlarged
Newton’s Color Disc
Description
To demonstrate the discovery made by Newton that white light is composed of seven colors. Consisting of a pulley mounted on a metal stand, the seven colored disc is driven by gears connected to a hand driven wheel. When the colored disc rotates, the eye can’t distinguish between individual colors and perceive it as white color.
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Digital, Stop Clock
Surber Stream Bottom Sampler
Genetics
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Monohybrid Crossing complete dominance Monohybrid Crossing incomplete dominance Dihybrid Crossing Monohybrid Crossing Mendelian explanation of Cross between tall & dwarf races in Garden Pea Sex linked inheritance Drosophila Mendelian Heridity of Blue & Adulsian fowls Mendelian Explanation of the breeding behaviour of Red & White flowering in 4 o’clock
Intestinal Villi
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Fuel Supply System Petrol MPFI Type
Fuel Supply System Petrol MPFI Type (Actual Working Model) Multi Point Fuel Injection
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under :
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Igniter & Ignition Coil
9. Distributor
10. Spark Plugs
11. Power Supply
12. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of MPFI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
Transaxle Gear Box With Differential
Transaxle Gear Box With Differential – 4 Forward & 1 Reverse Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
Insect Collecting Net
Description
Ring made of iron wire supported on handle with fine rubber grip at end. length of handle 75cm. 75cm long net bag fitted in ring through 5cm wide cloth rim, Dia of bag at free end 25cm, Ring dia 30cm. Insect Collecting Net With Aluminium Pipe Handle in powder coated paint Insect Collecting Net With Iron Pipe Handle in powder coated paint Insect Collecting Net With Wooden spirit polished Handle. Spare net bags for insect collecting nets / muslin / nylon / synch.
Sieve Shaker (Gyratory Motion)
Ensuring durability during performance, this machine is made of mild steel and cast iron and comes with one Lid and a Pan.
This unit is used with up to 7 sieves of 150mm or 200mm (8 Inch) sieves and up to 6 sieves of 300 mm (12 Inch).
Heavy duty motor (1/4 HP) ensures the whole performance through a reduction gear immersed in oil.
Along with featuring gyratory motion, this units also performs upward and downward movement ensuring that each "square cm" of the sieve is fully utilized.
This Gyratory Sieve Machine also supplied with a pair of rods and a holder which ensures tight grip of sieve set from the top.
| Product: | Gyratory Sieve Shaker | |
| Capacity: | 7 sieves of 150mm, 6 sieves of 300mm | |
| Design: | Table Top | |
| Construction: | Cast Iron, Painted Mild steel | |
| Motor: | ¼ HP | |
| Timer: | 0 - 60 Minutes | |
| Timer Type: | Digital / Analog | |
| Power Supply: | 220 Volts |
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
