XTEMOS ELEMENT
AJAX PRODUCTS TABS
Distillation Water Still (BARNSTEAD TYPE) Table Model S.S
Construction of Parabola
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Spherometer Demonstration Model
CONDENSER CLAMP
PRODUCT DESCRIPTION
- Three finger condenser extension clamp with Bose head.
- Aluminum stem the overall length of the clamp is 10.0.
- The extension rod contributing 6 the rubber coated jaws will open to 3.5 and will provide a six point contact for a firm
- The boss head right angle clamp will accept rods up to.63 /16 mm.
- 3 Finger Aluminium Condenser Clamp (Rubber Lined)
- 4 Finger Aluminium Condenser Clamp (Cork Lined)
- 3 Finger Brass C.P. Condenser Clamp (Cork Lined)
- 4 Finger Brass C.P. Condenser Clamp (Cork Lined)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Rain Gauge
Description
Rain gauge is designed to measure the precipitation. This small Version consisting of upper and lower housing part, measuring cylinder; Housing made of stainless steel, orifice rim made of brass. Type 7019.0000 can be supplied with a receiving area of 100 cm2. (This type is not conforming to meteorological standards). • Receiving area : 100 cm². • Rain measure (graduated glass) : 250 cm³. • Measuring range : 0 t0 25 mm precipitation (relative to a receiving area of 100 cm²). • Graduation : 1/1 mm precipitation. • Dimensions : dia 115 mm; height 300 mm. • Weight : approx. 0.8 kg.
Ray Box
Description
A ray box consisting of a rugged sheet metal box with a 12 V, 10 W festoon type axially straight filament lamp. Fitted with a cartridge for holding 4 types of slits – single, double, triple and wide slots Ideal for quick adjustment to get the desired ray/beam type Includes colour filters Also included is a convex cylindrical collimating lens for adjusting the beam to obtain long clear tracks which can be parallel, converging or diverging.
Smart Energy Meter
A Smart Energy Meter based on Analog Devices IC has been developed to build an Advanced Metering Infrastructure (AMI). The AMI system facilitates networking capability via GSM, ZigBee and ModBus. A Smart Energy Meter Development system has been developed by us, which consists of 1φ/3φ measurement section, a 32-bit ARM controller, wireless modules and powerful software. The student can completely understand the concept and usage of this trainer. This can be also used as one of the IOT server node.
Features
• 3 Phase energy readings displayed in the Graphics LCD • Simple design, Efficient and Highly Accurate • Easy connectivity for various loads • Keys to change the settings • Supports GSM, ZigBee and ModBus for networking • LPC2148 based processing board • 32/16 bit ARM7TDMI-S CPU with 60MHz maximum CPU clock • On board peripherals for extension • Graphics LCD interfaced to display the energy readings • Keys for various settings • Current Sensors and Voltage Sensors provided to measure 3 phase voltages and currents • Polyphase energy metering IC provides highly accurate energy measurement • Energy metering IC interfaced via I2C with Controller module • CC2530 Controller with maximum 32MHz CPU clock • High-speed and low-power 8051 CPU • 2.5GHz IEEE 802.15.4 compliant RF transceiver upto 250kbps data rate • UART Connectivity to interface with CPU
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Two Hinged Arch Apparatus
DESCRIPTION:
The two hinged arch is a statically indeterminate structure of the first degree. The horizontal thrust is the redundant reaction and is obtained y the use of strain energy methods. Two hinged arch is made determinate by treating it as a simply supported curved beam and horizontal thrust as a redundant reaction.EXPERIMENT:
• To study experimentally a two hinged arch for the horizontal displacement of the roller end for a given system of loading and to compare the same with those obtained analytically. • To obtain the influence line ordinates for horizontal thrust experimentally in a two hinged arch by moving a load along the span and to compare the same with those obtained theoretically.TECHNICAL SPECIFICATION:
• Apparatus has a span of 100cm and rise 25cm. • Both ends should have hinge but one of the ends should also be free to move longitudinally. • A lever arrangement fitted at this end for the application of known horizontal inward force for measuring the horizontal thrust. Along the horizontal span of the arch various points are marked at equidistant for the application of load. • This being a statically indeterminate structure of the first degree. • A dial gauge with 25mm travel (with magnetic base) is to be supplied with the apparatus. • Mild steel apparatus complete with a supporting stand and a set of weights.
Aids Virus
Description
HIV virus model is enlarged millions of times, shows the outer lipid membrane with protein structures and the internal nucleus which contains the viral hereditary matter [RNA]. The nucleus is removable and condoms can be put underneath to provide a message regarding measures to be taken for protecting against HIV infections. Supplied without condoms on stand with key card.
Spring Unit of Mechanical Model
Description
For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight. The steel shaft carries a clock spring with a free wheel device and winding ratchet, also an aluminium 'V' pulley 56 mm. diameter. One end of the shaft overhangs the base for use as line shaft when winding up a weight. Dimensions 220 x 100 x 100 mm. high Supplied complete with driving belt.
Westminister Electromagnetic Kit
Description
A very effective and motivating learning aid in elementary electromagnetism. Consists of 8 anisotropic alloy magnets, 8 ceramic ferrite magnets, 4 steel magnet yokes, 6 plotting compasses, 4 hardboard formers to take compasses, 1 bottle iron filings 250 gm, 4 dispensers for iron filings , 4 double C-cores, 4 clips for C cores, 4 Aluminium rings, 4 Aluminium split rings, 4 armatures with axle tubes, 4 Aluminium axle rods, 8 split pins, 16 rivets, 4 formers for coils, 4 reels cello tape, 4 reels copper wire, 4 sheets white pasteboard, 4 plain postcards, 4 reels white cotton thread, 1 length latex rubber tubing, 4 each resistors 100 ohms and 10 ohms, 4 support bases, 10 MES bulbs, 8 MES bulb holders,1 wood clamp and 1 wooden block. With instructions.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
Acrylic Ray Optics Set
P-N-P Transistor Unit
Ray box Multi Slit
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Manual Steering System
Steering System – Actual Working
Manual Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Thermal Conductivity Of Metal Rod
The apparatus consists of a copper bar, which is heated at one end, a heat sink is provided at other end. The test section of bar is properly insulated and thermocouples are attached along the length of bar. Heat conducted through the section of bar is measured by heat collection in water-cooled heat sink. A panel comprising of controls and measurements is provided, which provides easy operation and sturdy mounting of unit.
SPECIFICATIONS:
1.Metal Bar – 25mm of adequate length, provided with 8 Thermocouples along the length, Band heater at one end and water-cooled heat sink at other end. Test portion of bar is insulated. 2.Instruments panel comprising of. Voltmeter … 1No. Ammeter … 1No. Dimmerstat 0-230v, 2A, capacity. Multichannel Digital temperature Indicator. 3.Measuring flask and stop clockSERVICES REQUIRED:
1.Bench area of 1.5m. x 1m. at working height. 2.230 v, AC, electric supply with earthing connection. 3.Water supply at the rate of 2 lit/mm
Steam Power Plant Trainer
Introduction:
Steam Power Plant Working Unit – This Unit Helps The Students To Understand The Complete System Of A Thermal Power Plat. 1.Heat Energy Converts Water Into Steam 2.Steam Pressure When Moves A Engine Or Turbine Produces Mechanical Energy 3.Finally Mechanical Energy Is Converted Into Electricity Through AlternatorParts Details Of Boiler:
1.Boiler — For The Generation Of Steam We Have Provided Electrically Heated Boiler. 2.Diameter Of Boiler – 400 mm 3.Length Of Boiler – 600 mm 4.Heater 2 Pcs. – 3 KW (Each)
Autoclave, Radial Locking
Specification
Double wall chamber Autoclave. The inner chamber and outer wall made of stainless steel, ring made of stainless steel/ mild steel. The lid is made of stainless steel tightened by radial arms through a steering wheel made of chrome plated mild steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, inner container, S.S bucket and mild steel legs for Autoclave. The Autoclave can hold the in between 5psi to 20 psi. Autoclave, Vertical, Double Walled, Radial Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 23 litres | (10” x 18”) | |
| 40 litres | (12” x 22”) | |
| 52 litres | (14” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
