XTEMOS ELEMENT
AJAX PRODUCTS TABS
Funnel and Burette Combined Stand, Polished Wood
Deflection Of Truss Apparatus
Apparatus consist of 4 panels of a PRATT steel truss, each panel being 40cm in horizontal direction and 30cm in vertical direction. Load can be applied on each panel point. All tension members should be provided with detachable springs so as to obtain appreciable deformation of the member. Direction of the diagonal members may be changed. Apparatus can be used to illustrate visually the nature of forces set up in various members of the Truss. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Experimental Capabilities: Apparatus is supplied complete with a supporting stand and a set of weights.
Ball & Ring with stand
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted StructureXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
VM CRUCIBLE with Lid 25mm Dia x 38mm ht.
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
Gd Skin Color Advanced Trauma Simulator
Description
Features:
Washing, disinfection, hemostasia, enswathement etc. Open fracture, truncation trauma.Features of Advance trauma manikin:
Facial burn: I, II, IIIdegree. Laceration in forehead. The wound in jaw. Opened clavicular fracture and contusion wound on the chest. The wound in abdomen with small intension evisceration. Opened humerous fracture of right upper arm. Opened fracture of right hand (including parenchyma laceration, fracture and bone tissue exposure) Gun wound in the right palm. Opened fracture of right thighbone. Compound femur fracture of left thigh. Metal pricking wound in right thigh. Opened tibia fracture of right leg. Opened fracture of right foot with truncating trauma on small phalanx. Burns in left forearm: I, II, III degree. Truncating trauma on left thigh. Closed tibia fracture of right leg and contusion wounds in left ankle and foot.
Bryophyta, Pteridophyta
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Riccia structure & reproduction Marchantia structure & Life History Anthoceros structure & reproduction Moss (Funaria) life history Selaginella structure & reproduction Psilotum structure & life history Marselia structure & reproduction Lycopodium structure & life history Equistem structure & reproduction Fern (Aspidium) structure & life history Fern (Pteris) structure & life history Fern (Nephrolapis) structure & life historyXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Hydraulic Ram Test Setup
DESCRIPTION:
The Set-up is designed to study the Hydraulic Ram. Hydraulic RAM is used for pump little quantity of water to high head from a large quantity of water available at low head. It works on a principle of water hammer stating that “When flowing water is suddenly stopped in a long pipe a pressure wave travels along the pipe creating an effect of water hammer”. The Set-up consists of a pipe section fitted with a pulse valve and non-return valve, a supply reservoir on a stand which is connected to an overhead tank, an air vessel above the valve chamber smoothes cyclic fluctuations from the Ram delivery. Different pressure may be applied to the pulse valve to change the closing pressure and hence the operating characteristic. The flow rate of useful and waste water is measured using measuring tank and stop watch provided. Pressure and Vacuum Gauge are connected on delivery and suction side for the purpose of measurement.EXPERIMENT:
Ø To find out discharge of useful water and waste water. Ø To find out the efficiency of the Hydraulic RAMFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. Water Supply: Tap water connection ½ “ BSP Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Hydraulic RAM Ø RAM : Size 50 x 15 mm, Supply Head 2.5m, Delivery Head 10 m (max.) Ø Air Vessel : Suitable Capacity MOC SS Ø Delivery Line : For RAM, Dia 50 mm Length 6 m. Ø Pump : Capacity 1 HP, Crompton / Sharp / Hero make Ø Supply Tank : Capacity 150 Ltrs. Ø Overhead Tank : Capacity 100 Ltrs. Ø Measuring Tank : Suitable Capacity one each for useful and waste MOC SS fitted (2 Nos.) with Piezometer Tube & Scale Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Standard make On/Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
Bottle Filling Module
Specification
• One proximity sensor to detect the bottle presence • Opto coupler sensor to detect the bottle position. • A mechanical base fixed with stepper motor and gear mechanism provided to hold 5 bottles and rotate in circular motion. • A tank is provided to store the liquid. • One solenoid valve to control the volume of liquid flow into the bottle. • One Reservoir tank with FHP pump to feed the water to supply tank. • Two magnetic switches provided to maintain the level of water in supply tank.
Friction In Pile Lines Apparatus
DESCRIPTION:-
The Set-up consists of 2 pipes of different diameters, which are connected in parallel. Pressure tapings are provided on each pipe to measure the pressure losses with the help of a Differential Manometer. Control valves are fitted on each pipe, which enables to use one pipe at a time for experiment. Present set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the losses due to fiction in pipes Ø To determine the friction factor for Darcy Weis back equationUTILITIES REQUIRED: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pipes (2 Nos.) : Material GI of ½ “ & 1” Diameter Ø Pipe Test Section : Length 1 m Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank with Piezometer,Capacity 25 Ltrs. Ø Sump Tank : Stainless Steel, Capacity 50 Ltrs. Ø Stop Watch : Mechanical / Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. The whole Set-up is well designed and arranged in a good quality painted Structure
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Meter Scale, Hardwood
Handheld Anemometer Digital
Crucible with Lid Low Form
Description
Chemical porcelain crucibles are glazed inside and out, except outside bottom and rim. Crucible covers are completely glazed except for rim. For use in temperatures up to 1150 C (2102 F). Not recommended for minerals or metals.Capacity :
250mlHeight :
2.36 inch (60mm)Top Outside Diameter :
4.02 inch (102mm)
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Measuring Jugs
The Measuring Jugs, moulded in Polypropylene are clear, autoclavable and have good chemical resistance.
The Measuring Jugs are provided with a handle for easy & convenient lifting and have raise graduations for easy reading.
Adding to the existing range of Jugs, these short form transparent jugs, made of polypropylene are autoclavable and have non-drip spout.
These jugs have raised graduations, provide excellent contact clarity, & are provided with excellent thumb grip on handle.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Measuring Jug 250 ml | 12 | |
| Measuring Jug 500 ml | 12 | |
| Measuring Jug 1000 ml | 6 | |
| Measuring Jug 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 500 ml | 12 | |
| Measuring Jug (Euro Design) -1000 ml | 6 | |
| Measuring Jug (Euro Design) - 2000 ml | 6 | |
| Measuring Jug (Euro Design) - 3000 ml | 6 | |
| Measuring Jug (Euro Design) - 5000 ml | 4 | |
| Measuring Jug (Printed Graduation) - 100 ml | 12 | |
| Measuring Jug (Printed Graduation) - 250 ml | 12 | |
| Measuring Jug (Printed Graduation) - 500 ml | 12 | |
| Measuring Jug (Printed Graduation) - 1000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 2000 ml | 6 | |
| Measuring Jug (Printed Graduation) - 5000 ml | 4 |
AED Trainer
Description
The Laerdal AED Trainer 2 offers an affordable alternative for educating the layperson and healthcare provider in the effective use of an automated external defibrillator.Product benefits:
Educationally effective, offers all the essential features necessary for learning appropriate AED use and techniques. Affordable training through the simulation of the HeartStart FR2 AED in appearance and operation. Added instructor flexibility through unique control of the scenario selection by use of the remote control device. Flexible configuration of the device through a scenario builder program that allows the additional creation of custom training scenarios. Cost-effective operation through use of six C-cell batteries.Product features:
Ten pre-configured sudden cardiac arrest scenarios compatible with training programs developed by internationally recognized responder programs. Remote control (optional) for manual scenario selection pause/resume function, AED Trainer 2 volume control, motion artefact, low battery or replace battery, loose electrodes connection, shock able or non-shock able rhythms and error conditions that simulate the red X in the Heart Start FR2’s status display window. Designed for use with the AED Little Anne® and AED Resusci Anne® manikins with Laerdal LINK Technology by providing student feedback as to proper pad placement on the manikins. It can also be used with any other manikin where Laerdal Link Technology is not available. Proper pad placement required in order for the trainer to advance in the scenarios when used with the AED Little Anne or AED Resusci Anne manikins.
Behaviour Of Column Struts Apparatus
Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below:
1. Both ends pinned
2. Both ends fixed
3. One end pinned and other fixed
4. One end fixed and other end free
Apparatus to be supplied should be complete with a supporting stand and a set of weights.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Rocks Collection
Description
A comprehensive collection of igneous , metamorphic and sedimentary rocks, in wooden box with partitioned tray containing 50 specimens, each nominally numbered and enclosed in a transparent plastics bag. Specimens may be removed from bags for detailed examination. Each specimen is labelled also on the inside of the box lid, indicating the geological name.
