XTEMOS ELEMENT
AJAX PRODUCTS TABS
Level Control Measurement Module
This module consists of a process tank with a miniature pump, level sensor for 2 levels, a power supply, etc., To establish a ON/OFF control for the level of water. Circuitry is provided for stand alone operation or through a 8255 port of a Microprocessor kit.
Specification
• A transparent tank of height 150mm with adjustable electrodes to vary the high level and low level. • A pump with tank for water circulation • Water level can be monitored under software control/automatic mode • One power relay 230V/6Amp for pump ON/OFF control • Miniature connectors are provided to operate as stand alone controller or through software under a Microprocessor trainer. • Built in power supply.
Shunt Active Filter Trainer
Specification
• FPGA Spartan 3A DSP board used for generating the PWM signals. • Three phase 3 level diode clamped inverter used as a Active filter. • SRF (or) Instantaneous PQ theory will be used to generating reference current. • PI control or fuzzy logic will be used to regulate the dc link capacitor voltage. • Reference DC link Voltage will be 250V. • Hall effect current transducers used to sense the source currents, load currents and compensation currents. • Hall effect voltage transducers used to sense the dc link voltage and source voltages. • Necessary source inductor and filter inductor provided. • Input source Line voltage -200V (Peak). • Input source Current -10A (Peak). • Power Rating -3KW. • Reactive power compensation can be provided. • 3KW linear and non-linear loads will be given. • User can modify source, filter inductance and external loads. • User can modify control algorithm. • Industrial type cabinet provided. • Before compensation source current THD will be greater than 26% • After compensation source current THD - 2.5 - 4% in 3 level inverter - 4 - 5% in 2 level inverter
Artery model showing plaque building
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Concave Mirror, Spherical
Single Stage Air Compressor Test Rig
The test rig comprises of a Single stage air compressor fitted with an air tank with orifice, pressure gauges, and an energy meter to measure the input & a Temperature indicator measures the temperatures at various points. The compressor is mounted on air receiver along with the motor, and is provided with air relief valve (safety) and a pressure switch. The unit determines volumetric efficiency and isothermal efficiency at various discharge pressures
SPECIFICATIONS:
1.Air compressor – Single cylinder, Single stage type driven by a 2 hp. Three phase motor mounted on air receiver provided with delivery valve. 2.Air tank and orifice with water manometer for air intake measurement. 3.Pressure gauge to measure the discharge pressure. 4.Digital temperature indicator. 5.Energy meter to measure input power. 6.A technical manual accompanies the equipments .SERVICES REQUIRED:
1.Floor space of 2.5 X 1,5m. 2.440 V, 15A, 3ph. AC supply with neutral and earthing connection. 3.A hand tachometer.
Demonstraton Electric Bell
Manual Steering System
Steering System – Actual Working
Manual Steering System
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Peritoneal Dialysis Simulator
Description
For Continuous Ambulatory Peritoneal Dialysis. Designed to introduce patients, students, and nurses to the essentials of CAPD procedures and care. The realistic torso offers a realistic method to demonstrate and practice peritoneal dialysis. Success with CAPD is dependent on the patient’s following dialysis procedures with extreme care. This Life/form simulator gives the patient an opportunity to gain the confidence necessary for prolonged success with CAPD. Complete with indwelling Tenckh off catheter in a hard carry case. Dialysis materials not included.
PIPETTE BULB
Internally Expanding Mechanical Drum Brake System
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Human Torso Without Head
Human Histology
| Human Skin VS | Human Tongue Anterior Part TS |
| Human Tongue Posterior Part TS | Human Oesophagus TS |
| Human Stomach TS | Human Intestine TS |
| Human Intestine TS | Human Large Intestine TS |
| Human Vermiform Appendix TS | Human Spleen TS |
| Human Liver TS | Human Pancreas TS |
| Human Lung TS | Human Artery TS |
| Human Vein TS | Human Blood Smear |
| Human Trachea TS | Human Epiglottis TS Human Kidney TS |
| Human Bone TS | Human Nerve TS |
| Human Spinal Cord TS | Human Brain Cerebellum TS |
| Human Brain Cerebrum TS | Human Sperm Smear |
| Human Testis TS | Human Ovary TS |
| Human Oviduct TS | Human Mammary Gland TS |
| Human Vagina TS | Human Uterus TS |
| Human Thyroid Gland TS | Human Adrenal Gland TS |
| Human Cardiac Muscle TS | Human Salivary Gland TS |
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
DNA Model on Stand
Description
(Deoxyribonucleic acid) Model showing segment of D.N.A. molecule mechanism of replication, to show the double helix coiling and reforming, nucleotide and the structural formula to show the molecular shapes and bonds and angles distorted. Complete model arranged on a board, fully labeled.
Plantation Pots
Plantation Pots, moulded in polypropylene, are available in four different sizes.
The Plantation Pots have a downward extended rim, which provide convenient lifting even if the pot is filled.
The bottom of the pot is provided with holes for drain purpose.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Plantation Pots 100 mm | 20 | |
| Plantation Pots 150 mm | 20 | |
| Plantation Pots 200 mm | 20 | |
| Plantation Pots 250 mm | 20 |
Worcester Circuit Board
Description
Enables students to investigate nature and properties of electricity by using simple circuits which are easily constructed on a base board. The connector system uses P.C.B. strips with cut-out sections whose ends can easily be inserted in spring terminals, ensuring low contact resistance and ease of connection. The kit consists of : 1. Baseboard, plastic, with spring terminals and three battery holders. (1) 2. Batteries. (3) 3. Lamps 1.25 V MES. (10) 4. Lamp holders mounted on PCB connectors. (6) 5. Plain connector PCBs. (10) 6. Wire wound potentiometer with crocodile clip connections. (1) 7. Silicon diode. (1) 8. Resistor 3.9 ohm 2.5 W (1) 9. Pair Leads, red, with crocodile clip at each end. (1) 10. Pair Leads, black, with crocodile clip at each end (1) 11. Pair Leads, yellow, with crocodile clips at each end. (1) 12. Switches mounted on PCB. connectors (2) 13. PVC rod 15 cm long (1) 14. Soft iron nails, 5 cm long (2) 15. Bare copper wire, swg 20 (2 m) 16. Bare eureka wire, swg 34 (2 m) 17. Plastic covered copper wire (2 m) 18. Electrode support (1) 19. Pencil lead electrodes (10) 20. Sheet copper foil, 150 mm square (1) 21. Pack Steel wool (1) 22. Instruction manual in English. (1)XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Unit Cubes
Interlinking Cubes are one of the most widely-used math manipulative in the world. The colorful, interlocking cubes help children to learn number and math concepts. These cubes represent units and link in all direction. Interlinking cubes are used for patterning, grouping, sorting, counting, numbers, addition, subtraction, multiplication, division and measurement. Each unit is a cubic centimeter measuring 1 cm x 1 cm x 1 cm
Air Core Solenoid
Description
Air Core Solenoid helps investigate the magnetic field of a long coil. It can also used with the Current Balance as an accessory to measure the force on a conductor in a magnetic field. The solenoid has coils wound on a plastic tube with approximately 575 turns of copper wire. It can carry a current of 5 A continuously or 10 A intermittently.
Burner Bunsen-Economy
Description
This is one of most inexpensive option without flame stabilizer. The burner tube is made of brass and mounted on pressed steel powder coated base. Base dia is 80 mm. overall height of burner is 135 mm burner tube dia 12 mm. Suitable for LPG / Butane gas.Burner Specifications :
Tube Dia. - 12 mm Height - 130 mm Weight - 160 g
Ria Vial
These Polypropylene/Polystytene tubes are generally used in RIA , Coagulation & Bacteriology.
The Polypropylene tubes are clear and can withstand 3000 RCF during Centrifugation while the transparent Polystyrene tubes can withstand 1400 RCF.
The PP tubes can accept common acids, alkalis & solvents at room temperature while the PS tubes can accept mild bases, weak acids but not organic solvents.
Material : Polypropylene / Polystyrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| RIA Vail 12 x 75 mm / PS | 500 | |
| RIA Vail 12 x 75 mm / PP | 500 | |
| Cap For 12 mm RIA Tube | 100 |
Ultrasonic Transmitter And Receiver Set
This apparatus consists of a self-contained transmitter and receiver operating in the 40 kHz region. The transmitted wave is modulated at a user controlled variable frequency of about 2 kHz and this is detected by the receiver which amplifies the signal and drives a miniature integral loudspeaker. Both transmitter and receiver are contained in separate plastic enclosures measuring 175 x 100 x 40 mm which contain all the electronics and the 9 V batteries. The receiver has front panel 4mm sockets so that the output can be monitored on an oscilloscope for more quantitative measurements. The system is ideal for demonstrating sound waves above the hearing threshold and reflection properties associated with sonar etc. A special feature is the second transducer on the transmitter which can be switched on when required to produce two coherent sources. By moving the receiver along a line parallel to the two sources interference patterns can be dramatically demonstrated simplifying the Young’s slits experiment or enabling it to be demonstrated using waves other than light. Complete with batteries, full instructions and suggestions for use.
Transaxle Gear Box With Differential
Transaxle Gear Box With Differential – 4 Forward & 1 Reverse Actual Cut Section
The working of gear box is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of gear box are shown in actual working form. This model helps the student to understand the working of the gear box very easily. It is specially made dissectible for demonstration purposes.
