XTEMOS ELEMENT
AJAX PRODUCTS TABS
Test Tube Caps
The Test Tube Caps offered by us, come with a transparent polypropylene cap for test tubes, which proves to be an excellent protection to the contents of the tubes.
The grooves inside the cap tighten the fitting on the tube while the outer set in the tube making the combination a leak proof one.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Test Tube With Screw Cap 16 x 100 mm | 500 | |
| Cap For Test Tube Ø 25 mm | 500 |
Integer Counters
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Screw Gauge Micrometer Demonstration
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Band & Block Brake
Dicot & Monocot Root
Water Table Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Thermal Conductivity Of Liquid
Thermal conductivity of is an important engineering property. The apparatus uses guarded hot plate method for determining thermal conductivity. It consists of hot plate i.e. an electrical heater sandwiched between two plates. The heat loss from hot plate is prevented by using two guard heaters and heat of removes heat from liquid by circulation of water. Input to heaters the temperatures.
SPECIFICATIONS:
1.Guarded hot plate assembly comprising of main heater, ring guard heater and top guard heater, mounted over the liquid test cavity. 2.Cold plate assembly provided with water connections. 3.The assembly is housed in an enclosure box with glass wool insulation. 4.Instruments panel consisting of : a).Digital voltmeter and ammeter of suitable range. b).Dimmerstat for controlling input to the heaters (2 amp. 3 Nos.) c).Multichannel digital temperature indicator.SERVICES REQUIRED:
1.Floor space of about 0.75m. x 1.5m. at working height. 2.230v. AC electrical supply with earthling connection. 3.Water flow rate of about 10- 15 lit/min. at constant head.
Centrifugal Pump Test Rig
Centrifugal Pump Test Rig
Closed Circuit Type With S.S. Tanks, ISI Mark Pumps & Motors, Powder coated The closed circuit test rig consists of a “kirloskar make” monoblock centrifugal pump. The pump is provided with a vacuum gauge on suction pipe and a pressure gauge on discharge pipe. The gate valve is used to adjust the head on the pump. The discharge is measured by measuring tank / water flow meter. The input power is measured by energy meter.
Specifications:
l. Centrifugal monoblock- 1 h.p. 2. Pressure gauge and vacuum gauge for measuring the head. 3. Measuring tank of 400×400 x400 mm OR Water flow energy meter for measuring the discharge. 4. Stop watch. 5. Sump tank of sufficient capacity. 6. Energymeter to measure input power. 7. A technical manual accompanies the equipment.Features:
1. The equipment is coated with an attractive and anticorrosive powder coating. 2. The equipment consists of ISI standard (i) Monoblock ————————- Kirloskar make (ii) Energymeter ————————- Maxwell Jaipur make (iii) Water flow meter ————————- Kranti/Anand make.Services required :
(i) 440 v, 15 A, stabilized three phase A.C. supply. (ii) Floor area-2 mx2mxl.5m height (iii) Tachometer for speed measurement (can be supplied at extra cost)
Pressure Measurement Trainer
This module consists of a (0-100) psi pressure transducer of strain gauge type fixed in a pressure tank, one manually operated pump to develop pressure, pressure gauge and 3½ digital indicator to display the pressure.
Specification
• One metal pressure tank fitted with strain gauge type pressure cell. • A ball valve fitted in a pressure tank to release the pressure. • Bourden type pressure gauge provided in the tank to indicate pressure. • One manually operated foot pump to generate a pressure of the tank. • Signal conditioner for pressure cell output (0-5V) • Provision for offset/span adjustment. • A 3½ digit digital display indicator to indicate the pressure inside the tank
Calorimeter Stirrer, Copper
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Refrigeration Test Rig
Features
• 5 Nos of thermocouples are provided to measure the temperature at different points. • One multi channel temperature indicator is provided to display the temperature • One capillary tube and one thermo expansion valve is provided to check the performance separately. • Compressor supplies refrigerant through evaporator to find out cooling effect • 4 Nos. of Pressure Gauges are provided to measure the pressure at various point • One Energy meter is proivded to measure the overall power consumption • One voltmeter is provided to display the voltage. • One ammeter is provided to display the current.Specification
• Compressor :Hermatic • Capacity : 1/4 Ton • Supply : 230 V AC / 50 Hz • Condensor : 12 Coil • Evaporator : 15 Liter Capacity • Refrigerant : R134A
Stereo Zoom Microscope
Specifications
| Magnification | : | 20x & 40x or 30x and 60x | |
| Eyepiece Lens | : | Wide Field 10x or 15x Paired Eyepiece | |
| Objective | : | 2x and 4x (Turret Type Revolving) | |
| Focusing | : | Vertical movement with rack & pinion, Tension control knob & stroke 50 mm | |
| Inclination | : | 45° | |
| Tube Rotation | : | 360° Rotatable, Removable |
Accessories
Rubber Eye Guard. LED Light Illuminator or Flurescent Ring Illuminator.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Cryo Rack
Our Cryo Rack is moulded in polycarbonate making it tough, durable & autoclavable.
This handy Cryo Rack can hold 50 vials can be unscrewed without actually picking them up as the vial will lock in every well and hence will not twist.
This rack is provided with four anti skid rubbers & each well is identified with an alpha-numeric index.
Material : Polycarbonate
| Particulars | Pack (Pcs) | |
|---|---|---|
| Cryo Rack | 2 |
Permeability Cup
(S.S 304) 120mm Dia. Permeability cups for determining the water-vapor transmission of paints, varnishes, coatings, coating systems and related products.
The Permeability cup consists of a cup, seal ring and cover ring.
The seal ring is designed to prevent turning when closing the cover.
The Permeability cup is suitable for testing both self-supporting coating and non-self-supporting coatings. Water-vapor transmission is of interest for high humidity conditions.
The wet cup method is thus the reference method for determining water-vapor transmission, if agreed up on otherwise, other procedures or conditions the dry cup method may be used.
Ghat Tracer
Carboys
Carboys, made of polypropylene, are much lighter than glass.
These autoclavable, dependable & durable Carboys are provided with wide handles making it convenient while carrying or pouring purposes.
We also offer carboy with stopcock for the esteemed clients.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Carboy 10 ltrs. | 1 | |
| Carboy 20 ltrs. | 1 | |
| Carboy With Stop Cock 10 ltrs. | 1 | |
| Carboy With Stop Cock 20 ltrs. | 1 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Jet Pump Test Setup
DESCRIPTION:
The Set-up is designed to study the performance of Jet Pump. The Set-up consists of a Mono-Block Jet Pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
Ø To determine overall efficiency and pump efficiency of the Jet Pump Ø To plot Head vs. Discharge, Pump efficiency vs. DischargeFEATURES:
Ø Closed loop water circulation Ø Compact & stand alone set-up Ø MS Excel sample calculation program on demand Ø Stainless Steel tanks and wetted parts Ø Superb painted structure Ø Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC) 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½ “BSP, Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
Ø Product : Mono – Block Jet Pump Test Rig Ø Pump & Drive : Mono – Block Jet Pump, Size 32 mm x 25 mm x 25 mm (Suction x Pressure x Delivery), Capacity 1 HP Ø Supply Tank : Capacity 70 Ltrs. Ø Measuring Tank : Capacity 50 Ltrs fitted with Piezometer Tube & Scale Ø Medium Flow : Clear Water Ø Piping : GI / PVC Ø Stop Watch : Electronic Ø Pressure Gauge : Bourdon Type Ø Control Panel : Comprises of Energy Measurement : Energy meter Electronics, L & T make Ø MCB : For Overload Protection Standard make On/Off Switch, Main Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted structure.
three-phase-flying-capacitor-5-level-inverter-power-module
Specification
• Power circuit consists of 24Nos, 1200V, 20A IGBT with proper heat sink and snubber circuit. • 18 Nos of flying capacitor provided • 6 Nos, Power Diode @ 500v is provided for power circuit • 24 Noshigh speedopto-isolator provided for IGBT PWM inverter. • 24 Nos IGBT gate driver IC provided for IGBT gate driving • 22 nos isolated +15v dc @ 0.5A capacity provided for control circuit • One no of 3phase diode bridge rectifier@1200V, 20A with capacitor provided for input AC-DC conversion • 3 no of Hall Effect current sensor provided for O/P current measurement & protection circuit • 1 no Hall Effect current sensor provided for DC current measurement • Two no FRC connector provided for IGBT PWM input & ADC interface • MCB protection for input power ON/OFF & protection • One no of restart switch and LED provided for protection circuit indication & reset the unit • One Number of analog DC voltmeter provided for DC voltage measurement. • One number of power ON/OFF switch provided. • 3 Phase outputs & 3 Phase inputs are terminated in the front panel. • Test points provided for PWM input and current sensors output
3 Axis Robotic Trainer
For beginners, this Trainer is very useful to learn the concept and working of a Robo. For experienced people, this helps to make new ideas. This is used to study the ROBO characteristics of arm movement. Each axis has one AC servo motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move. Windows based user friendly software to control the arm through microcontroller having the flexible features such as
