XTEMOS ELEMENT
AJAX PRODUCTS TABS
Dissecting Trays
Autoclave, Radial Locking
Specification
Double wall chamber Autoclave. The inner chamber and outer wall made of stainless steel, ring made of stainless steel/ mild steel. The lid is made of stainless steel tightened by radial arms through a steering wheel made of chrome plated mild steel. The instrument is absolutely leak proof. Equipped with pressure gauze, safety valve, double safety valve, steam release valve, rubber gasket, inner container, S.S bucket and mild steel legs for Autoclave. The Autoclave can hold the in between 5psi to 20 psi. Autoclave, Vertical, Double Walled, Radial Locking.| Capacity (Lt.) | Size | |
|---|---|---|
| 23 litres | (10” x 18”) | |
| 40 litres | (12” x 22”) | |
| 52 litres | (14” x 22”) | |
| 60 litres | (14” x 25”) | |
| 75 litres | (16” x 24”) | |
| 95 litres | (18” x 24”) | |
| 180 litres | (22” x 30”) |
Resistance Box
Description
Resistance Box kit is an excellent device, which provides a very good learning technique in making different combinations of resistances, either in series or in parallel or in both ways to obtain the desired value of resistance for any circuit application. It consists of 10 resistors of equal values, i.e., 10Ω , 2 watts. These resistances are of ± 1% toleranceXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Plant Structure Microslide Sets, Plant Structure I – Angiosperms
Set of 19 slides, comprising
Allium, LS root tip for mitosis
Buxus, Lower epidermis
Capsella, LS ovule
Cucurbita, TS LS stem
Helianthus, TS stem old secondary
Ligustrum, TS leaf
Lilium TS Mature anthers pollen
Pollen grains
Ranunculus, LS flower Ranunculus, TS mature root
Ranunculus, TS stem
Stigma with pollen tube
Thickening
Tilia annual ringed
Triticum germinating seed
Vicia, young root hairs
Zea mays, TS root
Zea, TS LS stem
Zea, TS leaf
Diffraction Object Holder
Pilot Static Tube Set Up
DESCRIPTION:-
A Pitot tube is used to measure the local velocity at a given point in the flow stress. A Pitot tube of standard design made of copper / SS is supplied and is fixed below Vernier scale. The Vernier scale is capable to measure the position of Pitot tube in transparent pipe section. The pipe has a flow control valve to regulate the flow. A U-tube manometer is provided to determine the velocity head. Present Set-up is self-contained water re-circulating unit, provided with a sump tank and a centrifugal pump etc. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different flow rates. Flow rate of water is measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To find the point velocity at the center of a tube for different flow rates of water and calibrate the Pitot tube Ø To plot velocity profile across the cross section of pipeUTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATION: –
Ø Pitot Tube : Material Copper/SS of compatible size fitted with Vernier Scale Ø Test Section : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 40 Ltrs. Ø Sump Tank : Capacity 70 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Concave Mirror, Spherical
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Pulleys Bench Clamp Fitting
Jockey
Pregnancy Pelvis With Baby
Forceps (Different Types)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Table Counter Suitable for 100 tablet
Thermopile
Monocot Root T.S.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Longitudinal Wave Demonstration
Milling Tool Dynamometers
This is a simple and essay to understand set up introduce by sharp techno systems to study the behavior of cutting forces during milling operation in three directions. With this unit students can evaluate cutting depth, speed and feed. The unit works on standard method of octagonal ring with strain gauges. It is in to part one mechanical rings sandwiched between two M.S. plate with strain gauges fixed on it. This set of octagonal rings transmits the relevant data to the force indicator during milling operation.
FEATURES
1.Rigid construction & Compact Unit. 2.Assessment of cutting forces by giving due consideration to various parameters like depth of cut, material, cut, material, speed and feed. 3.Eassy in handling & Digital force indicators to measure three forces simuleniously.SPECIFICATIONS-
1.Mechanical sencing unit with set of octagonal rings and strain gauges. 2.Three channel digital force indicator with balancing potentiometers and polycarbonate front plate. 3.Range of force measurement in coordinate direction – 0 to 500 kg. 4.Over all size of mechanical unit- 300 x 300 mm.SERVICE REQUIRED
1.Necessary Milling Machine with automatic feed arrangement and tooling 2.230 volts, single phase, 50 Hz stabilized power supply.
Cylinderical Lenses
Description
Cylindrical lenses made of highly polished glass, magnifies in only one dimension. These lenses are used in transforming a point image to a line or changing the height of an image without changing its width.
| Size | Focal length | Add To Enquiry |
|---|---|---|
| Double-Convex | 50 x 50 mm | 75 mm |
| Double-Convex | 50 x 50 mm | 150 mm |
| Double-Convex | 50 x 50 mm | 200 mm |
| Double-Convex | 50 x 45 mm | 75 mm |
| Double-Convex | 50 x 45 mm | 150 mm |
| Double-Convex | 50 x 45 mm | 200 mm |
| Double-Concave | 50 x 50 mm | 75 mm |
| Double-Concave | 50 x 50 mm | 150 mm |
| Double-Concave | 50 x 50 mm | 200 mm |
| Double-Concave | 50 x 45 mm | 75 mm |
| Double-Concave | 50 x 45 mm | 150 mm |
| Double-Concave | 50 x 45 mm | 200 mm |
| Plano-Convex | 50 x 50 mm | 60 mm |
| Plano-Convex | 50 x 50 mm | 75 mm |
| Plano-Convex | 50 x 50 mm | 100 mm |
| Plano-Convex | 50 x 50 mm | 150 mm |
| Plano-Convex | 50 x 45 mm | 60 mm |
| Plano-Convex | 50 x 45 mm | 75 mm |
| Plano-Convex | 50 x 45 mm | 100 mm |
| Plano-Convex | 50 x 45 mm | 150 mm |
| Plano-Concave | 50 x 50 mm | 60 mm |
| Plano-Concave | 50 x 50 mm | 50 mm |
| Plano-Concave | 50 x 50 mm | 300 mm |
| Plano-Concave | 50 x 45 mm | 60 mm |
| Plano-Concave | 50 x 45 mm | 50 mm |
| Plano-Concave | 50 x 45 mm | 300 mm |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Mock Layout Of Car Wiring Conventional Type
It is an open type instructional apparatus. This unit is capable of operation when a standard battery is connected to the given terminals, Consisting of all essential parts as self starter, alternator, ampere-meter, ignition coil, distributor, 4 spark plugs, horn, long lights with dipper light, park-lights, dipper, back stop light and switches. The whole system is beautifully fitted on 100 x 80 cm base with electric motor working on 220 volts A.C and capable to drive the alternator. Without battery.
Demonstration Gear Model System
Description
A series of models to demonstrate different gearing systems. With transparent slideplates, the gears may easily be seen and where necessary there is an index on the primary and secondary shafts to show the change in the direction of rotation and the relative speed of rotation. A simple three-speed and reverse-gear system using spur gears. Reverse gear is obtained by interposing a small lay-shaft mounted pinion between the two main shafts. Gear selection is by means of a short ball-ended lever.
Anaerobic Culture Jar
Description
Transparent Anaerobic Culture Jar of 3.5.lit. capacity which is made of Polycarbonate. The lid of the jar is made of Aluminum pressure die Casting fitted with Pressure Valve, Vacuum Valve, Safety Valve & compound Pressure cum vacuum gauge, three finger aluminum clamp and sealing "O" ring. This is recommended only where inside air of jar is removed thru vacuum pump and CO2 is filled in the jar thru CO2 gas cylinder to generate anaerobic condition in the jar. Also supplied with plain aluminum pressure die casted lid which can be fitted when readymade gas packs are used to generate the anaerobic conditions inside the jar. When readymade gas packs are used, there is no need of lid fitted with dial gauge etc., for extra life of equipment.
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50Hz
Portal Frame Apparatus
DESCRIPTION:
Portal Frames used for the measurement of horizontal reaction are made stiffer by using M. S. flats rectangular cross section (10mm thick and 40mm wide). All are true to shape. The ends can be other fixed of hinged as desired. The end at which horizontal reaction, is to be measured, is provided with ball bearing rollers, which easily rolls on a smooth rolling platform. At the roller end a chord is attached which is connected further to spring balance. The spring balance records the horizontal reaction, for the measurement of slope and deflection. Both the columns of the portal frame can be clamped (fixed) or pivoted (hinged) and required.EXPERIMENT:
• To study the behavior of a portal frame under different end conditions.TECHNICAL SPECIFICATION:
• Apparatus made up of M.S. plate of rectangular section of 3mm thick x 40cm wide. • Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. • The size of portal will be 40cm x 60cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. • Apparatus is to be supplied complete with a supporting stand and a set of weights • Electronic load cells, displacement cell and Electronic Control Unit (ECU) provided with apparatus. • Software for digital calculations to easily performs by students.OPTIONAL ACCESSORIES:
• PC/Laptop Set.
4 Stroke 1 Cylinder Petrol Engine Manual Driven
The engine will be sectioned to show the internal constructional details. The working of individual part and accessories like Valves, Pistons, pumps, Crank and Camshaft, etc. will be demonstrated. It is provided with Flywheel and it is mounted on a sturdy iron frame. This actual cut section engine helps the student to understand about the parts and the working of the engine very easily. It is specially made dissectible for demonstration purposes. The actual cut section engine will be supplied with key card & very interesting literature regarding working.
