XTEMOS ELEMENT
AJAX PRODUCTS TABS
Open Wind Tunnel Apparatus
Technical Description
A wind tunnel is the classic experiment system for aerodynamic flow experiments. The model being studied remains at rest while the flow medium is set in motion, and thus the desired flow around the model is generated. Open wind tunnel used to demonstrate and measure the aerodynamic properties of various models. For this purpose, air is drawn in from the environment and accelerated. The air flows around a model, such as an aerofoil, in a measuring section. The air is then decelerated in a diffuser and pumped back into the open by a fan. The carefully designed nozzle contour and a flow straightener ensure a uniform velocity distribution with little turbulence in the closed measuring section. The flow cross section of the measuring section is square. The built-in axial fan with guide vane and a variable-speed drive is characterised by an energy-efficient operation at high efficiency. Air velocities of up to 28m/s can be reached in this open wind tunnel. The trainer is equipped with an electronic two-component force sensor.Lift and drag are detected and displayed digitally. The air velocity in the measuring section is displayed on the inclined tube manometer. The tube manometers is recommended for measuring the pressure curves in drag bodies. Extensive accessories allow a variety of experiments, for example lift measurements, pressure distributions, boundary layer analysis or visualisation of streamlines. The well-structured instructional material sets out the fundamentals and provides a step-by-step guide through the experiments.Learning Objectives & Experiments
– Determine drag and lift coefficients for different models – Pressure distribution when flowing around drag bodies – Boundary layer analysis – Investigation of flutter – Wake measurementFeatures
* Open wind tunnel for a variety of aerodynamic experiments * Homogeneous flow through the flow straightener and special nozzle contour * Transparent measuring section
Electric Motor St. Louis
Description
The motor consists of a two pole armature mounted between the ends of two bar magnets. The armature has a two section commutator and a pair of slip-rings on its shaft and is so constructed that the wire cannot slip off the iron core. The upper bearing and brushes for the commutator are mounted on a strong upright. Separate brushes are provided for the commutator and for slip rings and each are connected to a terminal. The magnets are held in position by thumb screws.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Light Dependent Resistor Unit (LDR)
Heat Transfer In Aagitated Vessel
The unit consists of a vessel with class wool insulation ail around. A helical coil made of copper is fixed inside the vessel. A motorized agitator is fixed at the center of the coil. The vessel is provided with an electric heater and a controller is also provided for vessel. Heater heats water in the jacket while cold water is circulated through coll. Temperature of circulated water and water In vessel Is measured and thus heat transfer coefficient at various agitator speeds can be determined.
SPECIFICATIONS:
1.Vessel approx. 20 lit. capacity, provided with glass wool insulation all around and electric heater at the bottom. 2.Agitator 150 mm dia, with 1/8 HP motor to drive the agitator. 3.Helical coil – 200 dia, 8 turns, made of 3/8″ dia. copper tube. 4.Controllers for heater and agitator motor. 5.Temp. Indicator for vessel water temperature and circulated water inlet and outlet.SERVICES REQUIRED:
1.Single phase 230V, 15 A stabilized supply. 2.Water flow at the rate of 4 to 5 lit. per min. 3.Suitable drain arrangement for water. 4.Floor area -1.5 mtr. X 1 mtr. X 1 mir height.
Decade Inductance Box – 7 Dial
Description
Housed in a box with seven dials and fitted with 4 mm output plugs, the unit allows a range of inductances from 1ΩH to 10ΩH. 7 Decade Inductance Box (i) 1ΩH to 10ΩH in steps of 1ΩH (ii) 10ΩH to 100ΩH in steps of 10ΩH (iii) 100ΩH to 1mH in steps of 100ΩH (iv) 1mH to 10mH in steps of 1mH (v) 10mH to 100mH in steps of 10mH (vi) 100mH to 1mH in steps of 100mH (vii) 1mH to 10mH in steps of 1mHXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Adjustable Slit
Zooplankton Net
Worm Sector Type Steering System
Worm & Sector Type Steering System – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
Ranging Rod
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Universal Multi Rack
Avail from us high quality Universal Multi Rack at affordable price range.
Souced from reliable vendors, this rack is an excellent lab apparatus compatible with different sizes of tubes.
Four sides of this rack can be used for tubes of 30mm, 20mm, 17mm & 12mm.High grade Polypropylene is used for its manufacturing.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Universal Multi Rack | 6 | |
| Rotatable Multi Rack | 1 |
Distributed Control System
A powerful, modular & upgradable DCS has been designed and configured based on Siemens controller SIMATIC PCS7 ASRTX (Micro Box). Distributed I/O system ET200M can be provided for field automation. The distributed I/O can be connected via Profibus, Communication. DCS consists of controller, Power supply unit, distributed I/O, Digital Input and Output modules, Analog Input and Output module. a Demo Panel and Simatic PCS7 V9.0 Software.
DCS Controller
• Make : SIEMENS. • Controller : SIMATIC PCS 7 AS RTX BOX. • Profibus Communication done via CP5611 onboard. • Transmission Rate of Profibus cable is 12 Mbit/s. • 2 x GBIT & RJ45 LAN • Core 17-3517 Processor 1.7GHz, 4GB DDR3 RAM, SSD 80GB, 4xUSB V3.0 • Mouse and Keyboard • Windows7 • Win AC RTX 2010 software controllerDistributed I/O station ET200M
• Support HART, PROFIBUS, Foundation Field bus. • 16 No’s of digital Inputs with 24V DC. • 16 No’s of digital Outputs with 24V DC. • 8 channels of Analog Inputs with 4-20mA. • 8 channels of Analog Outputs with 4-20mA. • 24VDC /10A inbuilt power supply.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Ball & Ring with stand
Lymphatic System
Test Tube Stand of 6 Holes, Wooden
Description
With vertical pins:
Wooden, polished stand with drilled holes, 2 of 25 mm dia. and 4 of 20 mm to accommodate 6 tubes with overall height of 9 cm and length of 20 cm. Vertical pins are provided for quick drying of the test tubes. Also available for 12 tubes, with 2 holes of 25 mm dia and 10 holes of 20 mm dia.Specifications :
Length : (in) 9.4 Width : (in) 3.5Without vertical pins and moulded supports:
Wooden with base and top with single row of 6 holes, clips together quickly and easily with two moulded supports. Height 11cm can accept two tubes of 30 mm and four tubes of 20mm diaSpecifications:
Length: (in)11.8 Width: (in)10.2Without vertical pins:
Wooden test tube stand - 6 holes of 22 mm dia. Test stand measures 9.5" long 2.5" wide base and 4.5" tall (Test tubes not included - shown for demostration )Specifications :
Weight: (lb)0.9 Length: (in)10.0XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Ray Box
Description
A ray box consisting of a rugged sheet metal box with a 12 V, 10 W festoon type axially straight filament lamp. Fitted with a cartridge for holding 4 types of slits – single, double, triple and wide slots Ideal for quick adjustment to get the desired ray/beam type Includes colour filters Also included is a convex cylindrical collimating lens for adjusting the beam to obtain long clear tracks which can be parallel, converging or diverging.
Line Ranger
Description
Our expertise enables us to develop a broad range of measuring and survey equipment and instruments such as Line Rangers. Manufactured using high grade metal and alloys, these line rangers can be availed in standard as well as customized sizes and specifications. Used for various testing and measuring activities by our clients, our range can be availed at most descent prices.
3 Axis Robotic Trainer
For beginners, this Trainer is very useful to learn the concept and working of a Robo. For experienced people, this helps to make new ideas. This is used to study the ROBO characteristics of arm movement. Each axis has one AC servo motor. Gripper has one miniature cylinder to pick and place the object. Software controls the ROBO arm and measures the motor axis and arm axis. Simplicity of this kit makes maintenance easier and friendly to user. This kit is very flexible to operate and easy to move. Windows based user friendly software to control the arm through microcontroller having the flexible features such as
Features
• Easy to learn • New design • Easy for maintenance • Drive by AC servo motor • Easy to programSpecification
• Arm : Jointed Arm • Axis : 3 • Motor : AC servo Motor • Gripper : Pneumatic • Drive : AC servo Motor Drive • Controller : MicrocontrollerBase
• Angle of movement : 300º • Gear Type : Spur Gear • Position Detector : Limit SwitchIntermediate ARM
• Angle of movement : 90º • Gear Type : Spur Gear, Worm Gear • Position Detector : Limit SwitchVertical ARM
• Angle of movement : 90º • Gear Type : Spur Gear • Position Detector : Limit Switch
Refrigeration Trainer General Cycle Type
The unit consists of vapor compression refrigeration cycle provided with components normally used in refrigeration system so that student can get familiar with the components. Various measurement provided enable students to estimate the performance of the system.
SPECIFICATIONS:
1.Compressor- Hermetically sealed compressor, having capacity of 0.3 T. 2.Expansion Devices a) Thermostatic Expansion Valve b) Capillary tube. 3.Evaporator coil. 4.Controls: a) Services Valve b) Solenoid Valve c) Filter-Drier for refrigerant d) High/Low pressure cutout e) Thermostat. 5.Measurements: a) Thermometers (mercury in glass) – 4 Nos. b) Pressure gauges for condensing and evaporating pressure. c) Energymeter for compressor d) Voltmeter and Ammeter for compressor. e) Rotameter for liquid refrigerant flow measurement. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 1m x 2m x 2m height. 2.220V, I5Amp, Single Phase Stabilized power supply
Half Wave / Full Wave And Bridge Rectifier Apparatus
Objective : To study Efficiency and Ripple factor in case of Half wave, Full wave and Bridge rectifier on application of load and filters.
Features : Instrument comprises of AC Power Supply, 3 meters to measure Output Voltage, Output Current and ripple factor on electronic AC Voltmeter, 4 PN Junction Diodes, Filter Circuit kit, load Resistances selectable using bandswitch and all important connections points at 4mm Sockets.
Optional Acc : Digital AC millivoltmeter.
Separating Throttling Calorimeter
AIM
To find out dryness fraction of steam by combined separating and throttling calorimeter.
