XTEMOS ELEMENT
AJAX PRODUCTS TABS
Orfice Mouthpieces Apparatus
DESCRIPTION:
An orifice is an opening made in the side or bottom of tank, having a closed perimeter, through which the fluid may be discharged. A mouthpiece is short tube fitted to a same size circular opening provided in a tank so that fluid may be discharged through it. Orifice and mouthpiece are used to measure the rate of flow of liquid. The apparatus is designed to measure the co-efficient of discharge of orifice & mouthpiece. The apparatus consists of a supply tank, at the side of which a universal fixture for mounting orifice or mouthpiece is attached. A centrifugal pump supplied the water to supply tank. Head over the orifice/mouthpiece is controlled by a by pass valve provided at pump discharge. A measuring tank is provided to measure the discharge. A gauge for measuring X and Y co-ordinates of jet from the orifice is provided, which is used to calculate Cv of orifice.SPECIFICATIONS:
[1] Supply Tank – 0.4 X 0.3 X 0.5m height [2] Orifice – 8mm and 10 mm. [3] Mouthpiece (a) LID = 4 (b) L/D = 1 (c) Bordas mouthpiece. (d) Convergent mouthpiece. [4] X-Y gauge for orifice jet co-ordinates. [5] Measuring tank of suitable capacity OR a calibrated water flow meter. [6] Sump tank of suitable capacity. [7] 0.5 HP pump with valve. A technical manual accompanies the unit.SERVICES REQUIRED:
[1] Flow surface 2 mtrs. X 1 mtr. X 1.5 mtrs. height. [2] 230 Volts, 5 Amp. Stabilized AC. Power Supply.
Reciprocating Compressor Actual Cut Section
This model will be made out of original parts. The model will be suitably sectioned to demonstrate the internal construction details showing the minute information, and working of the same, the model will be suitably painted and mounted on a metal or wooden base & supplied with key card & very interesting literature regarding working of the same.
Ohm’s Law Appartus
Description
To demonstrate Ohms Law. Consisting of a wooden enclosure with milliammeter, voltmeter, rheostat, push key and terminal posts. Requires an external battery (not supplied) and a suitable resistance (not supplied). Resistance can be calculated using Ohm’s Law by noting current and voltage. A rheostat is provided to control current flow. Circuit diagram is provided on the panel with instructions.
Floating Magnet Set
XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Bar Magnets
Description
Bar magnet pair with keeper Alnico Bar Magents (Pair) with spacer and keepers. Supplied in cardboard boxes Actual bars may be different size than stock photo. Bar Magnet Alnico (Pair) Size are mentions below which we have :- 38 x 10 x 5 mm (1.5") 50 x 10 x 5 mm (2") 75 x 10 x 5 mm (3") 100 x 10 x 5 mm (4") 150 x 10 x 5 mm (6")
Brush, Burette
Electromagnet
Hydraulic Power Steering System Motorised
Hydraulic Power Steering System (Motorised) – Actual Working
The working of steering system is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of steering system are shown in actual working form. This model helps the student to understand the working of the steering system very easily. It is specially made dissectible for demonstration purposes.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Brush, Burette
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Automotive Stethoscope
When components of an automobile engine are not functioning properly, they usually sound a warning in the form of noises not common to normal operations. Fortunately most noises posses characteristics of their own which help to identify the sources, coupled with some knowledge of their meaning. The unit is consisting of earphone, amplifier, switch and carbon microphone, assembled in a polished wooden box, Furnished with instructions, and a chart of possible different noise, probable source, mike position and how to check.
CNC Lathe Trainer Slant Bed
CONTROLLER:
Type of control system : PLC based system Axis motor and drive : Servo motor & drive with feedback Input ti servo : Optically lsolated Motor Drive : TTL compatible Interpolation : Linear/Circular /parabolic Cycles Used : G, M, S, T, F, I, K, M, F, Cycles : Circular interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuit and over Temperature Protected, Single Phase Protection Real Time Toolpath Simulation : providedMACHINE DETAILS:
Center Height : 100mm Swing over Carriage : 80mm Distance between Centre : 825mm Weight : 700kg Dimension in mm : 1250 x 900 x 1500 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron (Dia.) Automatic Lubrication : provided Tool Changer : Automatic – 8 stationSPINDLE:
Spindle Speed : Continuous Variable Spindle power : 2HP Inside Taper : MT3 Speed Range : 100 to 3000 RPMAXIS TRAVEL:
X Axos : 100mm Z Axis : 300mmXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Ultrasonic Interferometer
Ultrasonic Interferometer is a simple and easy to use unit for the accurate measurement of ultrasonic velocity in a Liquids and Liquid systems at the desired temperature (and at desired frequencies).
FEATURES:
• Accuracy in wavelength measurement – 0.01mm • Digital Panel Meter ( DPM) for observing the change in the reading between nodes /anti nodes (75mV approximate between a node and anti node) • Easy replacement of transducers with other frequency • Only one Liquid cell is required for all frequencies • Built in IC regulated power supplies. • The frequency of the Crystal oscillator at the piezo electric transducer is so matched at the 3 digit Decimal accuracy • The accuracy of Meter is 3 Digit Decimal • Stainless Steel based mechanical setup.ACCESSORIES:
• Liquid cell - One (with provision for water circulation) • Transducer (Longitudinal, 2MHz) - One • Micrometer assembly - One (with Tx)
Wooden Levelling Staff Telescopic type
Description
We bring forth an impeccable array of Wooden Leveling Staff to eminent customers. Products that we come up are ideally used to cater to the various needs and preferences of customers of various construction industry along with others. Therefore, this range is quality tested as per industry laid parameterst.
Serological Water Bath
Specifications
Material of Construction Inner chamber and lid Stainless Steel ,Outer chamber Mild Steel duly powder coated. Insulation Special grade mineral wool Heating- Immersion heaters Control panel - On/off switch - Heating and mains indicators - Thermostatic temperature controller Power- 220 V / 50 HzAccessories
Stainless steel top lid- Tray Optional Stirrer with 1/20 hp Motor with S.S. rod and blade - Digital Temperature Indicating Controller - Microprocessor based PID Digital temp. Indicator-Cum-Controller| Capacity | Load | Temperature |
|---|---|---|
| 14 Liters | 1.0 KW | Range:5°C above ambient to 100°C |
| 18 Liters | 1.5 KW | Sensitivity: ±0.5°C or better |
| 25 Liters | 2.0 KW | Sensor PT:-100 |
| 32 Liters | 3.0 KW | Accuracy: +/-5°C |
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Crucible with Lid Low Form
Description
Chemical porcelain crucibles are glazed inside and out, except outside bottom and rim. Crucible covers are completely glazed except for rim. For use in temperatures up to 1150 C (2102 F). Not recommended for minerals or metals.Capacity :
250mlHeight :
2.36 inch (60mm)Top Outside Diameter :
4.02 inch (102mm)
Drilling Tool Dynamometers
This is a armed wheel type strain gauge drill tool dynamometer designed to measure thrust and torque during drilling operation. This Dynamometer is suitable for drilling a hole up to 25mm size in mild steel. With this Dynamometer students can study the change in these force by varying speed, cut and feed
FEATURES:
1.Rigid in construction & Sensitive transuding and amplifying system for accuracy in force measurement. 2.Compact two channel digital force indicator. 3.Use of cutting fluid during operation is possibleSCOPE OF SUPPLY:
1.Mechanical sensing unit and work piece holder with strain gauges. 2.Control panel housing digital force indicator to measure both forces simultaneously, balancing potentiometer, connoting cables. 3.Necessary switches, fuses and screen printed front plate. 4.The dynamometer is calibrated at factory with help of proving ring and readings are directly in the from of kg.
Analytical Funnel
Our exclusive Analytical Funnel is designed specifically for analytical chemistry; the body of the Analytical Funnel is 60".
Moulded in polypropylene, these Analytical Funnel is provided with internal & external ribs to prevent air blockage.
We offer our Analytical Funnel at market leading prices.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Analytical Funnel 35 mm | 72 | |
| Analytical Funnel 50 mm | 72 | |
| Analytical Funnel 62 mm | 36 | |
| Analytical Funnel 75 mm | 36 | |
| Analytical Funnel 100 mm | 36 |
Shell Tube Heat Exchanger Water To Water
Heat exchanger is the devices used to transfer the heat from one fluid to other. The shell and tube heat exchanger is two tube single pass heat exchanger. The hot fluid is hot water obtained from water heater. The coil fluid is cold water. The schematic flow arrangement is shown in figure. Hot water enters the lower side of end box, flows through the tubes in lower half of shell and comes to the other end of the shell. It reverses its direction, flows through tubes in upper half of the shell and leaves out. Cold water enters lower part of the shell passes over the tubes between the baffles and leaves out the shell through outlet at upper surface of shell.
SPECIFICATIONS:
1.Shell – 150NB, 750 m.m. long provided with end boxes. a.One end box with divider plate. b.25% cut baffles – 4 Nos. in the shell. 2.Tubes – 4.5mm I.D., 6.35mm O.D.,250 m.m. length copper tubes with triangular pitch. 3.Instantaneous water heater, 3 Kw capacity, to supply hot water. 4.Thermometer for measuring the water temperature. 5.Valves to control hot and cold water flow.SERVICES REQUIRED:
1.3 P H, AC supply 2.Floor space 1.5m. X 1m, 3.230V, 15A, AC supply with earthing connection. 4.Water supply at the rate of about 10 lit/min at constant heat.
