XTEMOS ELEMENT
AJAX PRODUCTS TABS
Investigation With Mirrors Kit
Description
To Conduct basic experiments on the reflection of light from flat mirrors. The kit shows how adjacent mirrors reflect multiple images and demonstrates the principles of the periscope and kaleidoscope. The unit contains all the materials for the construction of a periscope and a kaleidoscope, including two sets of mirrors, mirror supports, and tubes. With instructions for assembly activity guide.
8085 Microprocessor LC LCD Trainer
Specification
• Intel 8085A CPU @ 6.144 MHz Clock speed. • RAM : 8KB expandable upto 32KB, Jumper selectable. • EPROM : 8KB expandable upto 32KB, Jumper selectable. • Lithium Battery Back up for RAM • PC Keyboard (104Keys) • 16x2 Alphanumeric Dot Matrix Liquid crystal display with back light • 3 Channel 16 Bit counter / timer terminated in a 10 pin connector using 8253 • 24/22 TTL I/O lines, terminated at 1 No of 26-Pin FRC connector by using 1 No of 8255/1No 8155 respectively • 8 Nos of Digital inputs terminated and given through on board 8 way Dip switch • 8 Nos of Digital outputs are terminated and displayed in the 8 Nos of SMD type LEDs • Digital I/O lines are terminated in 20-Pin connector • RS 232C compatible Serial port terminated in a 9-pin 'D' male connector • One VXT-Bus (50-Pin FRC Connector) for interfacing VBMB series of experiment boards for bus expansion. • Interrupts are terminated in a 5-Pin connector • Built in Line Assembler and Disassembler provided. • Software single stepping of user programs by instruction for software debugging.
Bar Magnets
Description
Bar magnet pair with keeper Alnico Bar Magents (Pair) with spacer and keepers. Supplied in cardboard boxes Actual bars may be different size than stock photo. Bar Magnet Alnico (Pair) Size are mentions below which we have :- 38 x 10 x 5 mm (1.5") 50 x 10 x 5 mm (2") 75 x 10 x 5 mm (3") 100 x 10 x 5 mm (4") 150 x 10 x 5 mm (6")XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Rear Axial Assembly With Differential Gear Semi
Rear Axial Assembly With Differential Gear Semi Floating Type – Actual Cut Section
The working of differential gear is shown with the help of actual parts assembled on square iron pipe frame. All the necessary parts of differential gear are shown in actual working form. This model helps the student to understand the working of the differential gear very easily. It is specially made dissectible for demonstration purposes.
Fiber Optics Communication Set
Objective:
To construct an optical transmitter and transmission of signal through Fiber Optics Cable. To construct an Optical Receiver and study the Attenuation of Signal when transmitted from Transmitter to Receiver end. Analog and Digital link can also be studied as this unit is complete with Sine and Square Waves. Bending losses can also be studied.
Features:
Instrument comprises of Microphone Preamplifier stages consists of MIC (Microphone), Preamplifier and Amplifier (Voice is converted to electrical signal and then amplified) and fed to LED (Transmitter) and then through fibre cable, signal is sent to Photodetector (Transistor) and again amplifier and output is sent to Speaker Unit. Power Supply of +6 VDC is used in Amplifier ckt. 2 No. Fiber Optics cables are provided (one of them is 50 cm long and the other is 100 cm long). One more fiber cable of 50mm length having connector at one end is also provided. Connectors a both end of fiber cable are provided for insertion in sockets provided on the front panel. Bending losses can also be studied in long wire.
Standard: MIC with 2 meter long lead and a Speaker 4, 4 ohm are mounted in a vertical box.
Accuracy: with 1 meter long connecting leads. 2 No. Fiber optic cable having length of 50 cm and 100 cm are provided.
Optional : Digital multimeter (3 1/2 Digit, Big size Display) This model also include Digital Multimeter and wooden frame for measurement of Numerical aperture i.e. complete in all respect including facility for measurement of numerical aperture.
Optical Bench, wooden
Description
A wooden base board with one meter scale divided into mm with following accessories: One each White face object and receiving screens each 150 x 100 mm with aperture mounted on wooden base with an index mark. Two plane mirrors 150 x 100 mm mounted as above. One lens holder V shaped, wooden. One needle vertically mounted in a short wooden rod on base. One candle holder on base. The components have the same optical center height.
Silicone Diode Unit
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Dynamo
Investigation With Mirrors Kit
Description
To Conduct basic experiments on the reflection of light from flat mirrors. The kit shows how adjacent mirrors reflect multiple images and demonstrates the principles of the periscope and kaleidoscope. The unit contains all the materials for the construction of a periscope and a kaleidoscope, including two sets of mirrors, mirror supports, and tubes. With instructions for assembly activity guide.
Wankel Engine Model
The model demonstrates the principle, operation. It is cutaway to show the internal constructional details. Unlike other engines the rotary piston engine avoids reciprocating parts. The power pistons an arch like triangular rotor which on rotating generates an epitrochoid. Mounted on metal base with printed diagrams.
Chik
Ovary TS Showing Oogenesis
Testis TS Showing Spermatogenesis
Primitive Streak TS
24 Hrs. Embryo TS Somite Region
36 Hrs. Embryo TS Typical
48 Hrs. Embryo TS Eye Region
48 Hrs. Embryo TS Heart Region 60 Hrs. Embryo TS Typical Region
72 Hrs. Embryo TS Heart Region
72 Hrs. Embryo TS Eye Region
48 Hrs. Embryo Sag. Sec.
60 Hrs. Embryo Sag. Sec.
72 Hrs. Embryo Sag. Sec.
96 Hrs. Embryo Sag. Sec.
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Constant Pressure Air Thermometer
Description
Jolly's thermometer bulb connected via a 3-way stopcock to mercury tube. Sliding indicator on right hand limb with reservoir sliding on vertical clamping rod. Metal vessel to surround the bulb. Mounted on wooden stand, height 740 mm. All glass parts except reservoir are made of borosilicate glass.
Matt White Screen
Multi Process Trainer
Features
• Pressure transmitter mounted at the bottom of the process tank • Flow transmitter (DPT) with rotameter mounted across the pipe line to sense the flow of water • Temperature sensor of (RTD) type mounted at the outlet of the heater • An industrial type heater as a heat source • FHP pump for water Circulation • SS Storage tank of 15 liters Capacity • Power driver provided to vary the pump speed and Heater Power. • Orifice plate is used for pressure drop measurement. • An electronic signal conditioner is provided. • Bourdon tube pressure gauge is provided to measure the tank. • Latest power driver is used to drive the pump & heater. • USB/Serial port data acquisition is provided.
Water Bath Tissue Flotation
Specifications
Double walled round construction. Inner chamber stainless steel/black anodized aluminum and outer made out of mild steel painted in epoxy powder coating. Thermostatic control, temperature range from ambient to 80°C. Complete with indicators, wire & plug. To work on 220V AC.Chamber Size In mms (dia x depth)
200x75 250x125XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Half lower Jaw small
Refrigeration Trainer Domestic Type
The unit enables students to study the various parameters affecting the performance of a domestic refrigerator. It consists of refrigeration cycle of domestic refrigerator, it consists a hermetically sealed compressor, air-cooled condenser, capillary tube and a natural convection type evaporator. The evaporator is fitted with a small heater to simulate different load conditions various measurements are provided so that power consumption, COP, theoretical and actual refrigerating effects refrigerant flow rate and effect of door opening on power consumption can be studied and also students can visualize automatic operation of unit using a thermostat.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirioskar make having capacity of approx. 1/25 ton of refrigeration. 2.Air – cooled condenser with natural convection airflow. 3.Capillary tube of matched length as expansion device. 4.Evaporator coil with an electric heater inside and adequate glass wool insulation on all side. 5.Measurement a)Energymeter Tore compressor input power measurement. b)Pressure gauge for condensing and evaporating pressure. c)Flow meter for liquid refrigerant flow d)Digital Temperature indicator for measurement of temperature 6.safety & Controls a)High & low pressure cutout. b)Thermostat. c)Necessary Switches. A technical manual accompanies the unit. Also, the unit is provided with an attractive and rust proof powder coating.SERVICES REQUIRED:
1.Floor space of 2m x 1m. 2.230V AC stabilized supply with earthing connectionXTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Composite Walls Apparatus
Composite Walls Apparatus:
The apparatus consists of a pair of M.S. plates, Bakelite, brass/aluminum. These plates in series on either side of the heater form a composite wall. The whole unit is clamped in a frame, which can be viewed through the Perspex sheet. The thermocouple tapings enables us to find out the conductivity and resistance of the composite walls.
SPECIFICATIONS:
1.Heater- Mica healer of dia. 250 mm. 2.Plates- a) M.S. plates of thickness 25mm & dia. 250mm.-2 nos. b) Bakelite plates of thickness 10mm & dia. 250mm.-2 nos. c)Brass/Aluminum plates of thickness 15mm & dia. 250mm.-2nos 3.Dimmerstat – 2 A capacity. 4.Measurements — a) voltmeter and an Ammeter to measure input power. b) Multichannel digital temperature indicator to measure temperatures at- various points. A technical manual accompanies the unit.SERVICES REQUIRED:
230 V, A.C. stabilized supply along with earthing connection. Bench area Im x lm x 0.5m height
Amplitude Shift Keying Modulation And Demodulation
This Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission and to study the Amplitude shift keying Modulation and Demodulation. Whole instrument is placed in plastic moulded box and 2 mm banana plug leads are provided for modulation and demodulation connections.
Technical Specification:-
1. Fixed Output DC Regulated Power Supply of ±12 V, +5 V.
2. 100KHz with 5 Vpp amplitude (Approx.) for carrier frequency.
3. In built square wave data generator.
4. Circuit diagrams for Modulator and Demodulator are printed on the milky white top panel.
Unit Cubes
Interlinking Cubes are one of the most widely-used math manipulative in the world. The colorful, interlocking cubes help children to learn number and math concepts. These cubes represent units and link in all direction. Interlinking cubes are used for patterning, grouping, sorting, counting, numbers, addition, subtraction, multiplication, division and measurement. Each unit is a cubic centimeter measuring 1 cm x 1 cm x 1 cm
PAM-PPM-PWM Modulation and Demodulation Trainer
PAM- PPM- PWM is the basic pulse modulation techniques. This trainer provides complete setup to the students for performing Experiments on these techniques. They can study Sampling, Pulse Modulation &Signal reconstruction process. Separate circuits are provided for each Techniques.
FEATURES:
• PAM- PPM- PWM Modulation and Demodulation Techniques,using Natural and Flat - top Sampling. • Natural Sample, Sample and Hold and Flat-top outputs. • Selectable 2 different sampling pulse frequencies on board. • On board Sine wave generators. • Voice communication using dynamic microphone and speaker • On board Filters and Amplifier • Functional blocks indicated on board schematic • Input- Output and Test points provided on board. • Built in DC Power Supply • Fully documented operating ManualTECHNICAL SPECIFICATION:
• Crystal Frequency : 6.14MHz • Sampling Frequency : 16 KHz, 32 KHz • Sine wave Generator : 1 KHz &500Hz, Amplitude (0-5)V, Tolerance +5% • Low Pass Filter : 4 Order BW Filter • Cut off frequency : 3.4 KHz • Voice Communication : Voice Link using dynamic mic& speaker • AC Amplifier : With Adjustable Gain control • Microphone type : Dynamic, 600 Ohm. • Audio Pre-amplifier : Op-amp based • Power amplifier : 1W Mono • Interconnections : BS2 Connector. • Power : 230V, 50Hz
Kaplan Turbine Test Setup
DESCRIPTION:
Kaplan Turbine is an axial flow reaction Turbine named in honor of Dr. B. Kaplan, a Gennan Engineer. This turbine is suitable for low head. The power produced by a turbine is proportional to QH. As the head (H) decreases the J discharge (Q) must increase to produce the same power. The present Set-up consists of a scroll casing housing a runner. Water enters the turbine through the stationary guide vanes and passes through the runner axially. The runner has a hub and airfoil vanes, which are mounted on it. The water is fed to the turbine by means of Centrifugal Pump. The runner is directly mounted on one end of a central SS shaft and other end is connected to a brake arrangement. A transparent hollow cylinder made of acrylic is fitted in between the draught tube and the casing for observation of flow on to the airfoil vanes. This runner assembly is supported by thick cast iron pedestal. Load is applied to the turbine with the help of this brake arrangement so that the efficiency of the turbine can be calculated. The Set-up is supplied with control panel. A draught tube is fitted on the Outlet of the turbine. The Set-up is complete with guide mechanism. Pressure and Vacuum Gauge are fitted at the Inlet & Outlet of the turbine to measure the total supply head on the turbine.EXPERIMENT:
1.To study the operation of a Kaplan Turbine 2.To determine the Output Power of Kaplan Turbine 3.To determine the Turbine EfficiencyUTILITIES REQUIRED:
● Water Supply and Drain.● Electricity 15 kW, 440V AC, Three Phase
TECHNICAL SPECIFICATIONS:
| MODEL | HM 109 (1.33 HP) | HM 109 (5 HP) | |
| Output Power | 1.33 HP / 1 Kw | 5 HP / 3.75 Kw | |
| Discharge | 1500 LPM (Approx.) | 5000 LPM (Approx.) | |
| Supply Head | 5 m | 5 m | |
| Rope Brake Dynamometer | Dia 200 mm | Dia 300 mm | |
| Sump Tank | Capacity 300 Ltrs. | Capacity 600 Ltrs. | |
| Water Circulation Centrifugal Pump | Capacity 7 HP, Three Phase | Capacity 20 HP, Three Phase | |
| Speed | 1500 RPM (approx.) | ||
| Runner | With adjustable Curved Vanes | ||
| Discharge Measurement | Pitot Tube with Manometer | ||
| Control Panel | Star/Delta Starter, Mains Indicator, MCB for overload protection | ||
| The whole set-up is well designed and arranged in a good quality painted structure. | |||
