XTEMOS ELEMENT
AJAX PRODUCTS TABS
Motorised Governor Apparatus
The unit consists of a base upon which the bearing holders and driving motor are bearing can be fitted in a holders to end conditions for test shafts, viz. Both end fixed and one end free, one end fixed. A Variac provided control of driving motor. The unit demonstrates the phenomenon of whirling of shafts with single rotor. As the test is destructive, after the test cannot be used, hence the unit only demonstrates the principle.
However, results obtained are closer to theory, as compared to those with bare shafts. Also, It can be demonstrated that, after passing whirling speed, shaft again starts running true.
SPECIFICATIONS OF MOTORISED GOVERNOR APPARATUS:
1.Test shaft – 4.75 mm, 6.35 mm and 7.9 mm – 2 each. 2.Bearing to provided end conditions, (a) Both ends fixed, (b) One end fixed and one end free. 3.Drive motor 1/8 HP, 1500 rpm with control arrangement. 4.The whole unit is mounted on a sturdy base. 5.Rotor for each shaft of suitable size. 6.A technical manual accompanies the unit.SERVICES REQUIRE FOR MOTORISED GOVERNOR APPARATUS:
Floor space area of 2m. X 1m. at working height. 230V, 15 A, AC electric supply connection.
Ultrasonic Interferometer
Ultrasonic Interferometer is a simple and easy to use unit for the accurate measurement of ultrasonic velocity in a Liquids and Liquid systems at the desired temperature (and at desired frequencies).
FEATURES:
• Accuracy in wavelength measurement – 0.01mm • Digital Panel Meter ( DPM) for observing the change in the reading between nodes /anti nodes (75mV approximate between a node and anti node) • Easy replacement of transducers with other frequency • Only one Liquid cell is required for all frequencies • Built in IC regulated power supplies. • The frequency of the Crystal oscillator at the piezo electric transducer is so matched at the 3 digit Decimal accuracy • The accuracy of Meter is 3 Digit Decimal • Stainless Steel based mechanical setup.ACCESSORIES:
• Liquid cell - One (with provision for water circulation) • Transducer (Longitudinal, 2MHz) - One • Micrometer assembly - One (with Tx)
Longitudinal Wave Demonstration
Bryophyta, Pteridophyta
Description
All Charts are made on PVC rexine, hand drawn, waterproof, in fast multi colors with a black background. Each chart is provided with rollers to hang on wall, Size 75×100 cm. Riccia structure & reproduction Marchantia structure & Life History Anthoceros structure & reproduction Moss (Funaria) life history Selaginella structure & reproduction Psilotum structure & life history Marselia structure & reproduction Lycopodium structure & life history Equistem structure & reproduction Fern (Aspidium) structure & life history Fern (Pteris) structure & life history Fern (Nephrolapis) structure & life historyXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Dicot & Monocot Root
Balance Spring
Light Kit
Description
Simple kit that helps explain students the principle of reflection and refraction. Using mirrors, lenses, acrylic prism set and a ray box, light can be reflected and refracted in different ways. The acrylic prism set includes a triangular, half-round, double convex and rectangular prism and two double concave prisms all packed in a wooden storage box. A Newton color disc is also provided with this set. The color disc illustrates an important property of light that white light is composed of seven colors. With instructions.
Insect Showcase Cabinet (Large)
Description
Provided with 53x45x9cm size drawer for keeping insects. Drawer of MDF with MDF sheet bottom and removable glass top is lined with 8mm thick EVA sheet and is glazed white from inside. Strips with provision for insecticide fitted inside drawer. Glass top frame designed to make box air-tight and pest proof. Fitted with index card holder and puller knobs. Nicely polished. Cabinet frame of plyboard with index card holder and puller knobs. nicely polished. Cabinet frame of plyboard with melamine lamination. Hinged door is provided with lock and handle and is lined with velvet. Insect Showcase Cabinet (Large) with 12 drawers Insect Showcase Cabinet (Large) with 24 drawersXTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Spring Unit of Mechanical Model
Description
For showing potential energy in a wound-up spring and its conversion to electrical energy by driving a dynamo and lighting a lamp. May also be used to wind up a weight on a cord showing the change from potential energy to kinetic and back to potential in the raised weight. The steel shaft carries a clock spring with a free wheel device and winding ratchet, also an aluminium 'V' pulley 56 mm. diameter. One end of the shaft overhangs the base for use as line shaft when winding up a weight. Dimensions 220 x 100 x 100 mm. high Supplied complete with driving belt.
Photon Energy Array
Human Torso With Interchangeable Sex Organs
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Precision Rotary Microtome
Description
A fully dependable sectioning equipment designed for precise sectioning of tissues up to 1 micron thickness. It has a front located feed indicator with cam drive system for accurate feed setting from 1 to 50 microns in steps of 1 micron. Prominent features include independent feed mechanism with automatic safety device, universal knife holder with lateral movement to permit use of entire knife edge, ball and flange type object holder for accurate centering of the specimen and full swing protective cover for easy cleaning and lubrication. The equipment assures smooth operation throughout the long life of the instrument as individual components are manufactured with modern techniques. The microtome razor is fabricated from fine grain steel alloy tested for microstructure and is heat treated to maintain its sharpness and strength. Supplied complete with one razor 120 mm with back and handle, a set of three object holders, one honing plate, oil can, dust cover, in wooden cabinet.
Two Hinged Arch Apparatus
DESCRIPTION:
The two hinged arch is a statically indeterminate structure of the first degree. The horizontal thrust is the redundant reaction and is obtained y the use of strain energy methods. Two hinged arch is made determinate by treating it as a simply supported curved beam and horizontal thrust as a redundant reaction.EXPERIMENT:
• To study experimentally a two hinged arch for the horizontal displacement of the roller end for a given system of loading and to compare the same with those obtained analytically. • To obtain the influence line ordinates for horizontal thrust experimentally in a two hinged arch by moving a load along the span and to compare the same with those obtained theoretically.TECHNICAL SPECIFICATION:
• Apparatus has a span of 100cm and rise 25cm. • Both ends should have hinge but one of the ends should also be free to move longitudinally. • A lever arrangement fitted at this end for the application of known horizontal inward force for measuring the horizontal thrust. Along the horizontal span of the arch various points are marked at equidistant for the application of load. • This being a statically indeterminate structure of the first degree. • A dial gauge with 25mm travel (with magnetic base) is to be supplied with the apparatus. • Mild steel apparatus complete with a supporting stand and a set of weights.
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
PLC Based Variable Frequency Drive Module
Specification
• PLC provided to control the variable frequency drive • PLC having Analog Input and Analog Output channels in range of (0-10)V DC • PLC having the digital I/Os in range of 24V DC • Communication cable (RS 232/Ethernet) will be provided communicate the PLC to PC • VF drive provided it operates at 230V AC supply • It provides the 3Φ AC output voltage • 3Φ AC Induction motor will provides. It operates at 415 AC, 3Φ, Frequency as 50Hz and rated 1500 rpm speed • PLC and VF drive mounted on the attractive printed panel trainer kit. • Variable pot meter, push button and connectors provided for experiment purpose
Sieve Shaker (Gyratory Motion)
Ensuring durability during performance, this machine is made of mild steel and cast iron and comes with one Lid and a Pan.
This unit is used with up to 7 sieves of 150mm or 200mm (8 Inch) sieves and up to 6 sieves of 300 mm (12 Inch).
Heavy duty motor (1/4 HP) ensures the whole performance through a reduction gear immersed in oil.
Along with featuring gyratory motion, this units also performs upward and downward movement ensuring that each "square cm" of the sieve is fully utilized.
This Gyratory Sieve Machine also supplied with a pair of rods and a holder which ensures tight grip of sieve set from the top.
| Product: | Gyratory Sieve Shaker | |
| Capacity: | 7 sieves of 150mm, 6 sieves of 300mm | |
| Design: | Table Top | |
| Construction: | Cast Iron, Painted Mild steel | |
| Motor: | ¼ HP | |
| Timer: | 0 - 60 Minutes | |
| Timer Type: | Digital / Analog | |
| Power Supply: | 220 Volts |
Coriollis Component Of Acceleration
This set up is designed to study coriollis component of Acceleration of a slider crank Mechanism. The apparatus uses hydraulic analogy to represent the rotating slider. It consists of a rotating block with two arms in opposite direction. These tubes can be rotated at various speeds by using a swinging field motor, which also acts as a dynamometer to measure torque applied to rotating tubes. A Perspex window on top cover helps to visualize the process. Rotameter is used to measure water flow rate through tubes. Water is circulated by small monoblaock pump.
Specifications:
1.Main Tank with fiberglass lining. 2.Rotating Arms 9/6 mm dia, 300 mm long. 3.Motor – Swinging field, D.C., 0.5 HP. 4.Rotameter 5.Monoblock Pump 6.Control Panel comprising of – (i) Speed Control Unit. (ii) Speed Indicator. (iii) Necessary switches. 7.Rigid support frame.Range of Experiment:
Coriollis Component of Acceleration can be determined at various speeds of rotation and water flow rates.Service Required:
1.A.C. Single Phase .230 V. stabilized supply. 2.Floor Space -1.5 m X 1.5 m.
Pneumatic Trainer Basic
LIST OF EXPERIMENTS
1.Operation of a Single Acting Cylinder 2.Speed Control Of Single Acting Cylinder 3.Operation of a Single Acting Cylinder with And Gate 4.Operation of Pneumatic Motor 5.Speed Control of Pneumatic Motor 6.Operation of D/A Cylinder with 5/3 Way Lever Operated DC Valve 7.Speed Control of D/A Cylinder with Flow Control (Meter In) 8.Speed Control of D/A Cylinder with Flow Control (Meter Out) 9.Speed Control of D/A Cylinder with Flow Control in Forward & Return Stroke 10.Sequencing of Motor & Double Acting Cylinder 11.Sequencing of D/A Cylinder with Single Acting Cylinder 12.Operation of Single Acting Cylinder with 5/2 Way Single Solenoid 13.Operation of Double Acting Cylinder with 5/2 Way Single SolenoidSALIENT FEATURES
1.Mobile self contained unit. 2.Simplicity of operation and designed for immature use. 3.Industrial components and circuits are demonstrated in the circuit. 4.Pneumatic valves of Shrader / Festo/ SMC or equivalent only. 5.Performance Guarantee of two years for any manufacturing defect. 6.Modular design with fitment of component at any corner of trainer. 7.Specially designed quick coupling.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
CNC Lathe Trainer2
CONTROLLER:
SIEMENS / FANUC Main Spindle Drive : AC Motor with VFC Z and X Drives : Stepper drive with Servo Motor Input to Servo : Optically lsolated Motor Drive : Smart & Intelligent Run Speed Control : Through Controller Interpolation : Linear/Circular /parabolic Cycles Used : G, M, S, T, F, I, K, M, F, Circular interpolation / Canned Threading : Straight / Taper Power Devices : Short Circuit and over Temperature Protected, Single Phase Protection Real Time Toolpath Simulation : ProvidedMACHINE DETAILS:
Center Height : 150mm Swing over Carriage : 125mm Distance between Centre : 825mm Weight : 1100kg Dimension in mm : 2000 x 1200 x 1700 Rapid Travel : 5000mm/min Resolution Z Axis : 1 micron Resolution X Axis : 1 micron (Dia.) Automatic Lubrication : Provided Tool Changer : Automatic – 4 station SPINDLE Spindle Speed : Continuous Variable Spindle power : 3 HP Inside Taper : MT4 Speed Range : 50 to 1800 RPMAXIS TRAVEL:
X Axos : 120mm Z Axis : 800mm
Signal Generator, Digital
This signal generator is a useful test instrument capable of generating multiple waveform and offers excellent waves shape, signal linearity, waveform symmetry and frequency range with selection of sine, triangular and square wave and amplitude variable 10 V peak to peak. 1 Hz to 100 kHz in five decade ranges selected by rotary switch named as frequency multiplier. Sine, triangular and square waveforms selected by push switch with LED indication. Output signal is 0 – 3.5 Vrms (10 V peak to peak) open circuit continuously control with uncalibrated amplitude control knob. Mains rocker switch with indicator Light. Signal Generator is versatile for general laboratory use; output signal is adjustable with the combination of frequency multiplier and set frequency dial with a low level of distortion. Set frequency is displayed on a 4 seven segment display. Output Voltage is continuously variable with selector range 1 V and 10 V.There is two pair of output safety sockets. One for CRO output (experiment for amplification, filter etc.) and another pair of sockets to speaker to drive a speaker and to demonstrate the audio signal frequency range 20 Hz to 20 KHz.
Amplitude Modulation And Demodulation
Instrument is design to demonstrate the method to transmit signals via. Electromagnetic transmission. It is still used in radio system to transmit audio signal although it has lesser in popularity compared to FM (Frequency Modulation) due to its lower signal to noise ratio.
Technical Specification :-
1. I C based DC regulated Power Supply ±12 V / 500 mA.
2. Audio frequency 1 KHz / 0-2 Vpp for modulating signal 455 KHz / 2.5 Vpp approx. for Carrier Frequency.
Venturimeter Orificemeter Calibration Set Up
DESCRIPTION:-
The apparatus consists of two pipelines emerging out from a common manifold. One pipeline contain a Venturimeter, second contains an Orifice. The pressure tapings from the Venturimeter and Orificemeter are taken to differential manometer to measure pressure difference. The Venturimeter and Orificemeter are connected in parallel and anyone of them can be put in operation by operating valves provided at the downstream. These valves can also regulate the flow. Present Set-up is self contained water re-circulating unit, provided with a sump tank and a centrifugal pump. Flow control valve and by-pass valve are fitted in water line to conduct the experiment on different floe rate. Flow rate of water is measured with the help of measured with the help of measuring tank and stop watch.EXPERIMENTS:-
Ø To determine the Co-efficient of discharged through Venturimeter and Orificemeter Ø To measure discharge through Venturimeter and Orificemeter as flow meters.UTILITIES: –
Ø Water Supply & Drain Ø Electricity Supply: Single Phase, 220 VAC, 0.5 kWTECHNICAL SPECIFICATIONS: –
Ø Venturimeter : Material Clear Acrylic, Compatible to 1” Dia pipe Ø Orificemeter : Material Clear Acrylic, Compatible to 1” Dia. Pipe Ø Water Circulation : FHP Pump, Crompton / Sharp make Ø Flow Measurement : Using Measuring Tank, Capacity 25 Ltrs. Ø Sump Tank : Capacity 50 Ltrs. Ø Stop Watch : Electronic Ø Control Panel : On / Off Switch, Mains Indicator etc. Ø Tanks will be made of Stainless Steel Ø The whole Set-up is well designed and arranged in a good quality painted Structure
