XTEMOS ELEMENT
AJAX PRODUCTS TABS
Solar Wind 3Φ, 2KW Smart Grid
This consists of 2 Microgrids of 2000W &1000W of power generation connected to a main Power Grid with all the components needed to convert a traditional Grid to a Smart so that many experiments can be conducted on this “Smart Grid”. A 3Φ 3KW isolation transformer with power input from utility grid will act as main grid to which 2 Microgrid will be connected through synchronizing panel. Optionally a commercial 3Φ, 2.5KVA Grid Commercial Solar Power Inverter can be added to this experimental setup. By adding 3Φ, 2.5KVA commercial solar inverter, when the experimental setup is not used by student, it may be used to generate power.
This Advanced Smart Grid Experimental Setup Consists of
• 2 Micro Grids, each 1000W of power generation using Solar, Wind or Hybrid • An Isolation Transformer Coupled to the utility Grid, acts as Main Grid to this Setup • Various other Power Sources • Commercial 3Φ 5KVA Grid Connected Inverter (Optional) • Optional Components for the Smart Grid Setup • DSP /FPGA Controller for PE, SG, PS Applications • Other Add ons • Components for Building 10/25KW Smart Grid Power Generation • IoT Based Data Acquisition.Solar Wind Grid Connected 3Φ, 2KW Smart Micro Grid
• Main Frame • 1KW Solar PV Module with Stand • Wind Turbine • DC-DC Boost Converter • 120V Battery Bank - 12V x 100AH x 10 Nos • 2KW Bi-Directional DC-DC Buck-Boost Converter for Charging battery • 2KW 3Φ Inverters • DSP/FPGA Controller • Microcontroller based Protection Relays • Smart Energy Meter • Synchronizing Panel • Three Phase RL Load 2KW • PLC with SCADA Software • 14 Channel PC based Power Quality Analyzer (Optional)
Human molar Teeth
Number Mat
Get kids to think on their feet! Number mat is fast and crazy quiz games make learning math fun!Kids listen the equation from teacher, do the math, and then step on the right answer. Play different games to reinforce numbers, counting, addition and subtraction up to the number 25. Great for classroom use. Mat measures 20 feet in length.
Digital Colorimeter
Description
The basic set-up of the colorimeter is: LED light source: Produces polychromatic light over the entire visible region, 45 Broad spectrum filter: The colorwheel has nine different filters. The filter employed is selected by wavelength. Each filter will produce monochromatic light at a specified peak wavelength with a bandpass of 20 mm. The filters enable the user to perform tests from 400 to 680 nm. Cuvette Holder: It holds the inserted cuvette during testing. It is imperative the cuvette be consistently oriented in the holder. Round cells usually have orientation markings to correctly position the cuvette. Detector: A silicon photo diode is used as the detector. The photo detector current will change as a function of light energy. Display:The current signal from the detector is converted to a numerical value, absorbance and is shown on led displayXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Insect Collecting Net
Description
Ring made of iron wire supported on handle with fine rubber grip at end. length of handle 75cm. 75cm long net bag fitted in ring through 5cm wide cloth rim, Dia of bag at free end 25cm, Ring dia 30cm. Insect Collecting Net With Aluminium Pipe Handle in powder coated paint Insect Collecting Net With Iron Pipe Handle in powder coated paint Insect Collecting Net With Wooden spirit polished Handle. Spare net bags for insect collecting nets / muslin / nylon / synch.
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Peritoneal Dialysis Simulator
Description
For Continuous Ambulatory Peritoneal Dialysis. Designed to introduce patients, students, and nurses to the essentials of CAPD procedures and care. The realistic torso offers a realistic method to demonstrate and practice peritoneal dialysis. Success with CAPD is dependent on the patient’s following dialysis procedures with extreme care. This Life/form simulator gives the patient an opportunity to gain the confidence necessary for prolonged success with CAPD. Complete with indwelling Tenckh off catheter in a hard carry case. Dialysis materials not included.
Mechanical Heat Pump Trainer
Heat Pump is a device to pump heat from one source to another. The heat obtained by heat pump is more than that could be obtained by direct electrical heating. The apparatus consists of refrigeration system with water cooled shell and coil type evaporator and condenser.
SPECIFICATIONS:
1.Compressor – Hermetically sealed compressor using R-12 refrigerant, having capacity 0.3 tons of refrigeration. Condensing pressure – max. 15 Kg/cm2 (Actual pressures will depend upon working conditions). 2.Condenser – Shell and coil type with continuous water flow arrangement. 3.Evaporator – Shell and coil type with continuous water flow arrangement. 4.Expansion Valve – Internally equalized thermostatic expansion valve. 5.Measurements – a) Rotameter for condenser & evaporator water flow rate measurement. b) Rotameter for liquid refrigerant flow measurement. c) Pressure gauges for condensing and evaporating pressure – 2 Nos. d) Thermometer for refrigeration cycle & water temp, measurement – 7 e) Wattmeter for compressor input measurement. f) Ammeter for compressor current measurement. 6.Controls – a) HP/LP cutout for compressor. b) Overload protector for compressor. c) Gate valve to control water flow rates. d) Necessary switches and fuse. A technical manual is accompanies the unit.SERVICES REQUIRED:
1.Floor surface area – 2m, X 2m. X 1.5m. height. 2.220V. 15Amp. Single Phase Stabilized power supply.
Flexible AC Transmission Systems
Three phase FACTS help the students to get insight of FACTS operation in Realtime by enhancing their understandings through various experiments. This module can be used to analyze the effect of shunt compensation (STATCOM- STATIC Compensator) series Compensation (SSSC - Static Synchronous Series Compensator) and Series - Shunt Compensation (UPFC - Unified Power Flow Controller) in the transmission line.
It consists of
• Generator Set-up (3Φ AC Source) • Simulated Transmission line • IGBT Based VSI Power Module • Series & Shunt Transformers with LC filter • RLC - Load setup • TMS320F2812 DSP Controller • Upgrade possibleGenerator Set-up (3Φ AC Source)
• 3 phase Alternator DC Motor Drive setup 3Φ / 1KVA / 1500 RPM / Salient Pole type coupled with 2HP/220V DC shunt motor and with suitable drive from 1Φ AC input supply with • suitable speed control, sensor and digital speed indicator. • Digital controller with IGBT based DC voltage controller for DC motor Armature Voltage variation 0-200V DC/10A & Alternator field voltage variation with necessary instruments • /meters/indicators.
Dicot Stem Anatomy T. S. & L. S.
Description
This model shows the transverse and longitudinal section of a dicotyledonous stem in which case the cambium ring has been formed but no secondary growth has yet taken place. Useful model for study of epidermis, lentice , cork layer, cork cambium, cortical parenchyma ,starch sheath, medullary rays, phloem, sieve plate, sieve tube, phloem parenchyma and inter fasicular cambium ,xylem, pitted vessels, bordered pitted vessels, annular vessels, spiral vessels, pith etc. Mounted on base, with key card.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Thermocouple, Single
Ring & Ball
Autoclaves Pressure Steam Sterilizers Economy
Specification
These autoclaves are made of 10 gauge aluminum. The drum is deep drawn & the ring on top is riveted. The lid is made by casting. Locking of lid by 6 nuts with rubber gasket seal in between (not metal to metal seal). Two safety valves, pressure gauge, flexible metal rubbing to exhaust air. Includes outer stand, inner aluminum container, inner tripod stand.| Capacity (Lt.) | Power | Size | |
|---|---|---|---|
| 20 Lt. | Electric | 300 x 300mm = 12” x 12” | |
| 20 Lt. | Non Electric | 300 x 300mm = 12” x 12” | |
| 25 Lt. | Electric | 300 x 380mm = 12” x 15” | |
| 25 Lt. | Non Electric | 300 x 380mm = 12” x 15” | |
| 35 Lt. | Electric | 350 x 380mm = 14"x15" | |
| 35 Lt. | Non Electric | 350 x 380mm = 14"x15" |
DNA Model on Stand
Description
(Deoxyribonucleic acid) Model showing segment of D.N.A. molecule mechanism of replication, to show the double helix coiling and reforming, nucleotide and the structural formula to show the molecular shapes and bonds and angles distorted. Complete model arranged on a board, fully labeled.XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Kipps Apparatus
Kipp's Apparatus, made of Polyethylene has three main portions.
The top portion is fitted with thistle funnel and a bulb structure through which dilute acid can be poured, which reacts with a metal sulphide in the base of the apparatus.
H.S gas then evolved collects in the fitted with a self-lubricating PTFE plug.
The base is provided with a residual outlet fitted with a cap for easy cleaning.
Material : High Density Polyethylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Kipp's Apparatus 250 ml | 1 | |
| Kipp's Apparatus 500 ml | 1 | |
| Kipp's Apparatus 1000 ml | 1 |
Calorimeter, Electric
Line Ranger
Description
Our expertise enables us to develop a broad range of measuring and survey equipment and instruments such as Line Rangers. Manufactured using high grade metal and alloys, these line rangers can be availed in standard as well as customized sizes and specifications. Used for various testing and measuring activities by our clients, our range can be availed at most descent prices.XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Magnetic Stirrer with Hot Plate
Maximum speed 1200 RPM.
Suitable for stirring all volumes, supplied with a teflon coated magnetic stirring bar.
