XTEMOS ELEMENT
AJAX PRODUCTS TABS
Magnetic Stirrer with Hot Plate
Maximum speed 1200 RPM.
Suitable for stirring all volumes, supplied with a teflon coated magnetic stirring bar.
Particulars
Magnetic Stirrer with Hot Plate, Volume 2 litre Magnetic Stirrer with Hot Plate, Volume 5 litreFeatures
Automation Type : Automatic Material (Body) : Mild Steel Material (Top Plate) : Stainless Steel Phase : Single Phase Power : 220 V Frequency : 50 Hz
Rheostat, Single Tube
Description
A layer of oxidized resistance wire is wound on a porcelain tube which is supported by end supports. A sliding contact and three 4 mm socket terminals are provided for use as a rheostat or as a potentiometer. Other ranges also available on request.| Ohms | Ampere | Tube length | |
|---|---|---|---|
| 23 | 2.3 | 150mm | |
| 10 | 3.3 | 150mm | |
| 22 | 2.8 | 200mm | |
| 24 | 3.3 | 250mm | |
| 28 | 4.2 | 400mm |
Wide Range Adjustable Micrometer
Description
Micrometer is used to measure short lengths accurately Technical Details : Printed Marking on the Vernier Scale Carbide Tipped Measuring Faces Blue Metallic Finsh Frame Plate Frame With Locking Clamp and ratchet stop Least Count: 0.01/0.001” Wide Range Measurement Interchangeable Anvils Type Sizes 300-400mm 400-500mm 500-600mm 600-700mm 700-800mm 800-900mm 900-1000mm 1000-1200mm 1200-1400mm 1400-1600mm Specifications: Guarantee ; 6 Months without abuse Packing ; Wooden Box Calibration ; In house.
Separating Throttling Calorimeter
AIM
To find out dryness fraction of steam by combined separating and throttling calorimeter.
PRODUCT DETAILS
The steam passing out from separating calorimeter may still contain some water vapour , in it . in other words it may not be absolutely dry . again , in a throttling calorimeter steam after passing through the throttle valve must be superheated or at least dry saturated . this limits the extent of dryness fraction that can be reliably measured , depend up on the pressure of steam in the main steam pipe . if a sample of steam, which may be still wet after passing through the throttle valve i.e it will not be superheated . thus under this condition the throttling calorimeter fails to enable us in determining the value of dryness fraction of steam . to overcome this difficulties we make use of separating and throttling calorimeter . first the steam is passed through separating calorimeter where itlosses most of it’s moisture and becomes comparatively drier, it is than passed through the throttling calorimeter where super heating takes place with out changr of total heat . the temperature and pressure of steam after throttling are measured by using a thermometer and manometer respectively.DESCRIPTION
The set up consist of a separating and throttling calorimeter . a steam generator is provided at the base of the apparatus . a thermostat knob is provided at the front of apparatus to control the temperature inside the steam generator . steam from steam generator is passed from separating calorimeter where most of the water partical get separated from steam and then passed to throttling calorimeter where steam get superheated . after that superheated steam passed through heat exchanger to condense the steam.SAPARATING CALORIMETER
It consist of two concentric chamber , the inner chamber ,and the outer chamber . which communicates with each other through an opening at the top. As the steam discharge through the metal baskets ,which has a large number of holes , the water partical due to there heavier momentum get separated from the steam and collected in the chamber. The comparatively dry steam in the inner chamber moves up and than down aging through the annular space between the two chambers and enters the throttling calorimeter .THROTTLING CALORIMETER
It consist a narrow throat . pressure and temperature are measured by manometer and thermometer . the steam after throttling process passed through the heat exchanger and condensate is collected .UTILITIES REQURIED
1.WATER SUPPLY 3 lit/min (approx) 2.Drain 3.Electric supply : 1phase , 220 V A.C , 2Amp. 4.Steam table for calculation 5.Space required : 1.0 m X 1.0 mXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Skeleton Model, Miniature
Car Chassis Rear Wheel Drive Actual Cut Section Motorised
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.
Burner Bunsen LPG
Porcelain Combustion Boat
Description
We offer Porcelain Combustion Boats all around the world. These Porcelain Combustion Boats are made available in varied specifications and grades. Besides, our Unglazed Porcelain Combustion Boat is highly demanded in European, Asian and other markets for its quality and diverse laboratory applications.| Capacity (ml) | Height (mm) | Width (mm) | Length (mm) | |
|---|---|---|---|---|
| -- | 10 | 12 | 80 | |
| -- | 11 | 13 | 86 | |
| -- | 11 | 13 | 90 | |
| -- | 11 | 13 | 120 |
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
CNC Lathe Trainer
Controller:
Type of control system: PLC based system Main Spindle Drive : AC Motor with VFD Z and X Drives : Stepper drive with Ramp function Input to Stepper : Optically Isolated Motor Drive :TTL Compatible Run Speed Control : Computer controlled with software Interpolation : liner / Circular /Parabolic Cycles Used :G,M,S,T,F,I,K,M,F Cycles : Circular Interpolation /canned Threading : Straight/Taper Power Devices : Short Circuits and over Temperature Protected Real Time Tool Path Simulation : ProvidedMACHINE DETAILS:
Center height : 100mm Swing over Carriage : 80mm Distance between Centre : 300mm Longitudinal Travel : 310mm Weight : 800kg Dimension in mm : 1300 x 800 x 1400 Rapid Travel : 700mm/min Resolution Z Axis : 5micron Resolution X Axis : 5micron Automatic : providedAXIS TRAVEL:
X Axis : 80mm Z Axis : 310mmSPINDLE:
Spindle Speed : Continuous Variable Spindle Power : 2 HP Inside Taper : MT3 Speed Range : 50 to 3000Rpm
Model AC DC Generator
Pole Holder
Description
We are supply of high quality Pole Holders for prisms. These have been manufactured using the finest quality of aluminium and brass, in order to ensure their strength and durability. We provide the poles in the shape of a tripod for increased sturdiness while holding prisms and other survey instruments. We also offer customization and can supply these products in accordance with the demands of our clients.The specifications of the Pole holder :
• Manufactured using fine quality aluminium and brass • High on parameters like strength and durability • Improved sturdiness while holding survey instrumentsXTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Linear Expansion
Description
Apparatus is fitted on heavy channel base, at one end of which is an adjusting screw, at the opposite end is a micrometer screw reading to 0.01 mm for measuring the expansion. Supplied with one each of aluminium, brass and iron expansion rods but WITHOUT thermometer. Consisting of metal rod 500 mm in length and 4.5 mm dia. enclosed in a well - lagged, metal tube with three tubules for steam inlet, outlet and thermometer. The metal rod to be investigated is supported in the steam jacket by detachable rubber bungs situated at each end of the tube.
Microwave Integrated Circuit Trainer
This trainer is used to study Microstrip components and its characteristics. A useful trainer to get hands on experience on Microstrip components and instrument. We offer Three solutions.
1GHz RF Source with Detector
• Frequency Range : 0.05 to 1GHz. • Resolution : 100KHz. • Automatic Level Control (ALC) RF Detecter& Directional coupler provided for many RF measurements. • Output Impedance : 50 Ohm.1GHz Micro Strip Component
• Ring Resonator. • 3dB Power divider. • Direction of Coupler.
Cam Analysis Apparatus
The apparatus is designed to study the cam profiles and performance of cam and follower system. The apparatus consists of a shaft supported by ball bearings upon which three different types of cams can be mounted.
The push rod for follower is supported vertically, which can adopt three different types of followers. Cams and followers can be changed easily. A variable speed motor rotates the cam. A dial gauge permits plotting of follower displacement with respect to cam position. By operating the system at different Speeds, jump speed can be found and also the effect of weight and spring force on jump speed can be studied. Jump can be visualized also with the help of stroboscope (it is not supplied With the product).
SPECIFICATIONS OF CAM ANALYSIS APPARATUS:
1.Cam -Eccentric, tangent and circular ARC type – one each. 2.Follower- mushroom, flat faced and roller type – one each. 3.Cams and followers are hardened to reduce wear of the surfaces. 4.Variable speed motor coupled to camshaft of suitable range and Variac. 5.A dial gauge to note the follower displacement. 6.A technical manual accompanies the equipment.SERVICES REQUIRE FOR CAM ANALYSIS APPARATUS:
1.230 V, A.C. stabilized supply along with earthing connection. 2.Bench area 0.5m x 0.5m x 0.5m height. 3.Tachometer to measure the jumping speed, (can be supplied extra)XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Forced Convection Apparatus
The unit consists of a circular pipe; loosing heat by forced convection to air, being forced through it. Constant heat flux is added to pipe by an electrical heater, provided with input control. The pipe surface temperature is measured at various points along length of pipe. Temperature of air at inlet and outlet of test section are measured. Thus the students can calculate local and overall heat transfer coefficients in forced convection, at various airflow rates and various heat flux values.
SPECIFICATIONS:
1.Test pipe – 32mm NB GI pipe, 500 mm. long, heated by band heater, outside. Centrifugal blower to force air through test pipe with How control valve. 2.Variac 2A, capacity to force air through test pipe with flow control valve. 3.An orifice meter with differential water manometer. 4.Voltmeter and Ammeter to measure heater input. 5.Multichannel digital temperature indicator to measures various temperatures. 6.A technical manual accompanies the unit.SERVICES REQUIRED:
1.Bench area of about 1m. x 0.75 m. at working height. 2.239v, 15A, AC, supply with earthing connection.
Heat Transfer Activity
Straight Joint
Masses Iron
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Digital Multi Meter
Description
| D.C. Voltage | 200mV-1000V +0.5% +2 digits | |
| A.C. Voltage | 200V-750V +1.2% +10 digits | |
| D.C. Current | 200mA-10A +1% + digits | |
| Resistance | 200Ohms-2000kOhms+0.8%+2 digits | |
| Max. Display | 1999 | |
| Display Size | 16x48mm., 3½digits LCD | |
| Range | Manual | |
| Transistor Test | Yes Standard | |
| Accessories | Battery, Testing Probes with Instruction Manual, in case, CE Marked |
Telegraph Kit
Description
Students can discover how people communicated long distances before the telephone with the Telegraph Kit, students can learn Morse code and even send a secret message to a friend. Kit includes: D cell battery holder, contact key, light bulbs, alligator connector cords, buzzer and instruction manual
