XTEMOS ELEMENT
AJAX PRODUCTS TABS
SILICA MOISTURE DISH With Lid – Translucent
Kidney With Bladder
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connection
RF Signal Source with Detector
Specification
• 25 to 6000MHz RF synthesized signal generator. • Programmable attenuator 5, 10, 20, 30dBm up to 1.5GHz. • 40 x 2 LCD Display to display the frequency of the RF signal and RF signal level. • Output level : 0dBm +/2dB upto 1GHz, -5dBm, +/-2dB upto 3GHz, -10dBm, +/-3dB upto 6GHz. • Output impedance : 50 ohm. • One RF Power detector provided for 50 to 1000MHz frequency range and this output is measured • by an ADC and display on the LCD display. • 6 Keys keypad provided to select the desired frequency, attenuation level, Sweep mode. • Step size : 1MHz. • Connectors: - 2 Nos. of 'N' type connector for RF out and RF in. - One "BNC" type connector for RF detector output.  XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Pinned Joint Model
SPECIFICATION:
Model consists of hinged. Model will be able to demonstrate the qualitative behavior of the truss under load. As are very flexible, a compression members will easily it`s bucking i.e. It will curve of plain. The tension member however remains straight and tight. The student will therefore have a visual picture of the type of stresses i.e. Compressive or tensile that member of truss will carry under various positive of the load. In case of pinned joint truss, the student will be able to observe that angle between members at each joint undergo a small change.
Transmission Line Trainer
This trainer is designed for study of co-oxial cable characteristics like Impedance measurement, VSWR measurement etc., It is based, i) The latest technology of DDS Based RF source. ii) Directional coupler for VSWR Measurement. iii) TDR to measure the cable fault.
Specification
• DDS RF Source - Frequency: 10 to 400MHz. - Step Size: 1KHz. - Direct Digital Synthesis (DDS) Method Based. - Since DDS Device is primarily digital, it offers. • Display: Graphics LCD display of 240x128 pixels with backlight to plot VSWR, TDR characteristics etc., • One directional coupler provided for VSWR, Return loss measurement. • In-Built RF Detector for 10-400MHz Frequency range. • In-Built TDR (Time Domain Reflectometer) to measure and study nature of discontinuation in the co-axial cable. • Output Impedance: 50 ohms. • Co-axial cable: Various lengths of 50 ohm, 75 ohm cables supplied. • All relevant waveforms are displayed graphically in the Graphics LCD
Theodolite
Description
We bring forth for our customers watts theodolites which are scientific instruments extensively employed in surveying and engineering work. These are mainly used for measuring angular values in a traverse or network between survey marks. Watts theodolites can also determine a line of sight along a level plane by combining a spirit level and a telescope. Our range of products is subject to customization to meet the needs of our clients, and can be availed reasonable rates.Watts theodolites is mainly used for :
• Surveying and engineering work • Measuring angular values in a traverse or network • Determination of a line of sight along a level plane
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Distillation Plant (Manasty Type), Wall Hanging
The unit is recommended for making pyrogen fee distilled water of a very high degree of purity, Made out of S.S. special kettle element is fitted with Ejection Device / Auto cut for safety of the element is provided water supply is stopped.
The cork fitted to the unit is of brass C.P.A. wall Mounting clamp is provided with the unit.
Supplied with cord and plug to work on 220/240 volts A.C. Stainless Steel, Output approx. 3/4 Ltr./Hr.
Stainless Steel, Output approx. 5/6 Ltr./Hr.
Aluminium Dicasted, Output approx. 3/4 Ltr./Hr.
Aluminium Dicasted, Output approx. 5/6 Ltr./Hr.
Vortex Shaker (Test Tube Shaker)
Compact Vortex Shaker
Compact, rugged construction. Heavy metal base & rubber feet prevent movement of the shaker during use. Choice of continuous & touch mode. Variable speed control. Include one hand insert, micro tube insert & cup attachment.Product Details
Maximum speed : 3000 rpm Usage : Laboratory Capacity : 600ml
Water Bath Tissue Flotation
Specifications
Double walled round construction. Inner chamber stainless steel/black anodized aluminum and outer made out of mild steel painted in epoxy powder coating. Thermostatic control, temperature range from ambient to 80°C. Complete with indicators, wire & plug. To work on 220V AC.Chamber Size In mms (dia x depth)
200x75 250x125
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Immersion Heater
Digital Kymograph
Digital Kymograph has gained immense recognition in exporting and supplying quality assured array of Digital Kymograph Consists of a revolving drum that is wrapped with a sheet of paper and this kymograph is used to measure atmospheric pressure, the functioning of steam engines and tuning fork vibrations. Offered kymograph is made in complete compliance with predefined industry norms at our well-equipped unit. Furthermore, this Digital Kymograph is extensively appreciated and demanded in the market due to its rugged design and excellent performance.
Features
Excellent performance. Power efficient. Easy operation. Result accuracy.Specification
Digital Speed Selection. Spirit Level: For adjusting level. Auto Stop after One Complete Cycle. 16 x 2 LCD Digital Display with Back Light simultaneous display of all functions on the display and selection through display. Highly Accurate Speed : E/C System Speeds available -0.12.,0.25,0,.50,0.75,1.00,1.25,mm/Sec With Accurance of +/-0.01%. Timer With Alarm Time Multiplier (o-10 min in multiple of 30 sec.) for indicating washing Cycle Drug Injection times etc. Very Low Power Consumption (12 volts 1 Amp.). Operated with Stepper Motor which is highly accurate and run by Microprocessor based program. Battery Back Up (Optional): Auto Conversion to Battery Mode in Case of Electricity Failure. Back up 1 to 4 hours. Special Chrome Plated and Powder Coated Body: Extremely Resistant to Corrosion and Leak Proof Design. Self Lubrication Gear. And More Feature Available.
Ni Cad Battery Investigation
Description
This setup is designed to investigate the charging and discharging characteristics of typical re-chargeable batter with external voltmeter and ammeter connected, you can manually measure the input and output energy by taking reading from these meters. A toggle switch is provided to select between charging and discharging. Connection are made via 4 mm plugs.
Rear Suspension System
In this model the working of rear suspension system is shown with the help of actual parts assembled on a metal stand. All the necessary parts of a rear suspension system are shown in actual working form. This model helps the student to understand the working of the rear suspension system very easily. It is specially made dissectible for demonstration purposes.
(A) Leaf Spring Type Suspension System With Rear Rigid Axle
(B) Rear Independent Type Suspension System
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Gas Turbine/Turbojet Engine
Human Head And Neck L. S.
Periscope, Wooden
Young’s Moduluds Appratus
Comprises a scale plate carrying a 0 to 30 mm scale, and a moveable vernier readable to 0.1 mm.
Both have bars with clamping screws for the wires and hooks for the tension weight and loading masses.Supplied with clamp for fitting.
A tension weight, mass 1.3 kg approx. for the comparison wire is also included.
Complete with load masses and wires.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
MCT Twin Rack
We provide Twin Purpose MCT Twin Racks for both 0.5 & ml. & 1.5 ml. micro centrifuge tubes.
Each side has 108 holes for 0.5 & 1.5 ml. MCT's respectively.
The transparent top of MCT Twin Rack provides and excellent view and a protection cover for the tubes stored.
Each face of the base has a unique alpha-numeric index for easy identification of the tube.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| MCT Twin Rack (Rack for 0.5 ml & 1.5 ml MCTS) | 4 | |
| MCT Box (Rack for 100 MCTs of 0.5 ml) | 4 | |
| MCT Box (Rack for 64 MCTs of 1.5 ml) | 4 |
Lathe Tool Dynamometers
This is a strain gauge type two component lathe tool dynamometer designed to measure vertical and horizontal forces on the while orthogonal cutting process. The unit is in two parts one is mechanical sensing unit or tool holder, which can mounted on the top of the Ross slide after removing swivel base and compound slide of a lathe and digital force indicator. With this Dynamometer student can study the change in these forces by varying Speed, Cut and Feed.
FEATURES:
1.Rigid in construction 2.Sensitive transuding and amplifying system for accuracy in force measurement. 3.Compact Digital force indicator. 4.Use of cutting fluid during operation is possible.SCOPE OF SUPPLY:
1.Mechanical sensing unit or Tool Holder with string gauges. With H.S.S. tool of ½ “ size. 2.Control panel housing digital force indicator to measure two forces simuletensiously, balancing potentiometers, connoting cable. 3.Necessary switches, fuses and polycarbonate front plate. Range o to 500 Kg. 4.Centre Height, P.C.D.of clamping bolt size, clamping Bolt size. Three component lathe tool dynometer is also available.
Plate Type Heat Exchanger Apparatus
The unit consists of a plate type heat exchanger, in which cold fluid is cold water and hot fluid is hot water, which is obtained from geyser. The inlet and outer connections of the fluids are positioned so as to make the exchanger counter flow type. Hot and cold fluids pass between alternate plates various measurements provided enables the students to determine heat transfer rate, LMTD, heat transfer coefficients and effectiveness of the heat exchanger.
SPECIFICATIONS:
1.Heat Exchanger- S.S. Plate heat exchanger wiles nos. of 200 X 400mm. 2.Geyser to obtain hot water – 3 KW capacity. 3.Calibrated water flow measuring vessel 4.Thermometers to measure inlet and outlet temperatures of fluid. 5.Flow controls valves. A technical manual accompanies the unit.OPTIONAL ACCESSORIES:
Rotameters to measure water flow rates instead of measuring vessel. Multi channel digital temperature Indicator to measure the temperatures instead of thermometers.SERVICES REQUIRED:
1.Floor space 1.5m. X 1m, 2.230V, 15A, AC supply with earthing connection, 3.Water supply at the rate of about 10 lit/min at constant heat.
