XTEMOS ELEMENT
AJAX PRODUCTS TABS
Silicone Diode Unit
Cylinderical Lenses
Description
Cylindrical lenses made of highly polished glass, magnifies in only one dimension. These lenses are used in transforming a point image to a line or changing the height of an image without changing its width.
| Size | Focal length | Add To Enquiry |
|---|---|---|
| Double-Convex | 50 x 50 mm | 75 mm |
| Double-Convex | 50 x 50 mm | 150 mm |
| Double-Convex | 50 x 50 mm | 200 mm |
| Double-Convex | 50 x 45 mm | 75 mm |
| Double-Convex | 50 x 45 mm | 150 mm |
| Double-Convex | 50 x 45 mm | 200 mm |
| Double-Concave | 50 x 50 mm | 75 mm |
| Double-Concave | 50 x 50 mm | 150 mm |
| Double-Concave | 50 x 50 mm | 200 mm |
| Double-Concave | 50 x 45 mm | 75 mm |
| Double-Concave | 50 x 45 mm | 150 mm |
| Double-Concave | 50 x 45 mm | 200 mm |
| Plano-Convex | 50 x 50 mm | 60 mm |
| Plano-Convex | 50 x 50 mm | 75 mm |
| Plano-Convex | 50 x 50 mm | 100 mm |
| Plano-Convex | 50 x 50 mm | 150 mm |
| Plano-Convex | 50 x 45 mm | 60 mm |
| Plano-Convex | 50 x 45 mm | 75 mm |
| Plano-Convex | 50 x 45 mm | 100 mm |
| Plano-Convex | 50 x 45 mm | 150 mm |
| Plano-Concave | 50 x 50 mm | 60 mm |
| Plano-Concave | 50 x 50 mm | 50 mm |
| Plano-Concave | 50 x 50 mm | 300 mm |
| Plano-Concave | 50 x 45 mm | 60 mm |
| Plano-Concave | 50 x 45 mm | 50 mm |
| Plano-Concave | 50 x 45 mm | 300 mm |
Wave Machine, Powell’s
Car Chassis Front Wheel Drive Actual Cut Section
Car Chassis Rear Wheel Drive Actual Cut Section – Motorised
4 Stroke 4 Cylinder Petrol Engine With Clutch, Gear Box, Propeller Shaft, & Rear Axle Assembly With Differential Gear
The chassis of the four stroke four cylinder engine cut section model. The cut section model is constructed such that all the following systems can be demonstrated in working conditions.
ENGINE:
Maximum parts and accessories of an engine like cylinders, cylinder head, inlet and Exhaust manifolds, FIP, injectors, self-starter, alternator, water pump, radiator, etc., are sectioned to show the internal constructional details. The complete sectioned model is coupled with FHP 220/230V A.C single phase motor through a Reduction drive unit.TRANSMISSION SYSTEM:
This system consists of a Clutch and four speed gearbox assembly, the casing of which is suitably cut to demonstrate its operation. The gearbox is coupled to Differential gear box with propeller shaft and the different coupling used for this transmission can be demonstrated. The Differential gear box is also cut so as to clearly to demonstrate its complete operating principle. The gear shifting including the forward and reverse gear operation can be clearly shown. The speed variation and the rotation of the Differential gear box can be seen while gear shifting. By running the motor connected to the engine assembly the entire system with gear box, rear axle etc. can be demonstrated in running. FUEL SYSTEM: The Fuel tank is cut to expose the mounting of the level sensor and the position of Fuel section. The system is complete with mechanical Fuel pump. EXHAUST SYSTEM: It consists of Exhaust Manifold and silencer in cut section to explain internal construction. LUBRICATION SYSTEM: It consists of the engine Lubrication system along with the Lubrication oil pump is suitably sectioned. SUSPENSION SYSTEM: This will explain both the Hydraulic Suspension systems at the front and the leaf spring Suspension at the Rear. One of the hydraulic arrangements of Suspension mechanism is highlighted (with shock absorbers) and explained cut sectionally.BRAKING SYSTEM:
The Hydraulic or Air circuit Brakes. The movement of the Brake Shoes on operating the brake pedals can be seen in the area where the Brake drum is cut. The front and rear brakes will be operational. STEERING MECHANISM: The can be seen and included in the Steering wheel. Steering gear box and coupling of the same to the wheels will be shown by rotating the steering wheel, the operation of the steering system can be demonstrated. The entire system will be mounted on the chassis, and suitable mounting option with caster wheels will be provided for easy movability.XTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Flourimeter (Digital)
A digital photofluorometer, you can perform precise analysis of flurophors and quinine.
Designed specifically for life science laboratories, this smart instrument fulfills your requirements of accurate results with the sensitivity you demand.
This fluorometer is a compact system, which occupies very low bench space, while offering convenient and excellent throughput for fluorescence assays.
It is a fluorometer model has been designed and manufactured for laboratories, where routine analysis of fluorophors is a prime requisite.
This system uses 50 W tungsten halogen lamp,
This digital fluorometer greatly enhances productivity of your laboratory, designed with latest technology, use of imported mechanical and electrical parts, imported lamp and other components; it allows you to perform fluorometric determination of quinine more quickly.
| Covers entire visible range: | Excellent detection sensitivity | |
| Compact and efficient: | Bright red seven segment LED display | |
| Occupies low bench space: | Precise analysis of Flurophors & Quinine |
Specifications
| Fluoro Sensitivity: | Full-scale deflection obtained with 1 ppm quinine sulfate in 0.1 N sulphuric acid (primary wavelength 360 nm) | |
| Display: | 3 digits bright red seven segments LED display | |
| Excitation Source: | 12V, 50W Tungsten Halogen Lamp | |
| Sensitivity Range: | Adjustable in 4 ranges | |
| Detector: | Highly sensitive wide range photodiode/cell | |
| Sample Test Tube Size: | 15 mm (D) x 80 mm (H) | |
| Minimum Sample: | 4 ml | |
| Power: | 230 V ± 10%, 50 Hz. AC | |
| Dimension: | 260 x 335 x 160 mm (Approx.) |
Sonometer, Simple
Human Digestive System
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Flexible AC Transmission Systems
Three phase FACTS help the students to get insight of FACTS operation in Realtime by enhancing their understandings through various experiments. This module can be used to analyze the effect of shunt compensation (STATCOM- STATIC Compensator) series Compensation (SSSC - Static Synchronous Series Compensator) and Series - Shunt Compensation (UPFC - Unified Power Flow Controller) in the transmission line.
It consists of
• Generator Set-up (3Φ AC Source) • Simulated Transmission line • IGBT Based VSI Power Module • Series & Shunt Transformers with LC filter • RLC - Load setup • TMS320F2812 DSP Controller • Upgrade possibleGenerator Set-up (3Φ AC Source)
• 3 phase Alternator DC Motor Drive setup 3Φ / 1KVA / 1500 RPM / Salient Pole type coupled with 2HP/220V DC shunt motor and with suitable drive from 1Φ AC input supply with • suitable speed control, sensor and digital speed indicator. • Digital controller with IGBT based DC voltage controller for DC motor Armature Voltage variation 0-200V DC/10A & Alternator field voltage variation with necessary instruments • /meters/indicators.
Seven Segment LED Display Circuit
A common anode seven segment module is fitted on a board with 8 bit dip switch to control the each segment of seven segment LED display. The inputs A-D of a display driver are connected to the binary coded decimal (BCD) outputs from a decade counter. A network of logic gates inside the display driver makes its outputs a-g become high or low as appropriate to light the required segments a-g of a seven segment display. A resistor is required in series with each segment to protect the LEDs
Brush, Cylinder
Polariser and Analyser (Polaroid)
XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Heat Pipe Apparatus
Heat Pipe Apparatus:
Heat pipe is an interesting device, which is used to transfer heat from one location to another.
The apparatus consists of three pipes, viz. A heat pipe, copper pipe and stainless steel pipe. Ail the pipes have same physical dimensions. Copper and stainless steel pipes serve the purpose of comparison of heat pipe performance. All pipes are mounted vertically with a band heater at lower end and water filled heat sink at upper end. Nearly isothermal operation of heat pipe is clearly visualized from longitudinal temperature distribution of the pipe.
SPECIFICATIONS:
1.Heat pipe – Stainless Steel pipe, 25 mm O.D., 450 mm. Long. Sealed at both ends, evacuated and filled partially with distilled water – one No. 2.Copper and stainless steel pipe of same size as that of heat pipe – one each. 3.Equal capacity heater at bottom end of each pipe. 4.Water filled heat sinks at upper end of each pipe.Measurements and controls
a) Dimmerstat to control heat input to all the heaters – 4 amp. Capacity One No. b) A voltmeter and an ammeter to measure input to heaters One each. c) Multichannel digital temperature indictor to measure temperatures along the length of pipes.Four thermocouples are provided on each pipe. v Thermometers to note down water temperatures in heat sinks – 3 Nos.Services Required:
230 VA.C. Single Phase supply. Floor Area = 1 m X 0.5m X 0.5 m height.
Tuning Forks Set, Even Frequency
Induction Coil
Description
This box form Induction Coil has a 50 mm spark gap and can produce pulses of high voltage spark from a low voltage direct current source such as a battery. It is suitable for use with gas-filled discharge tubes, vacuum tubes, eudiometers and for general laboratory work. It is comprised of two coils fully enclosed in a polished wooden case with binding posts. Spark gap at the discharge points can be adjusted by sliding rods back and forthXTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Barlow Wheel
Description
This apparatus spins an electrically charged brass wheel spin, without the aid of a motor. When the wheel electrified by a voltage source (battery), the slotted brass disc sets up eddy currents throughout the structure. This electricity is then attracted to 4 strong neodymium magnets, causing the wheel to spin.
General Science Charts
Description
Poly art Charts are multi colored, accurate in details, printed on plastic, laminated on both sides, washable, non-tearable and long lasting with plastic rollers, size 75 x 100 cm. Insects Reproduction of Plants (Part 1) Seed parts, Germination & Pollination Reproduction of Plants (Part II) Mendel’s Law, supply of Oxygen, Carbon Dioxide and Nitrogen. The Bird, Food, Beaks and Jaws Plants and their parts (Part I) Flower Plants and their parts (Part II) Root & Stem Types of Animals (Part-1) Paramecium, Amoeba, Hydra, Worm, Crayfish, Spider Types of Animals (Part -II) Fish, Amphibians, Reptiles, Birds and Mammals Foods and their uses Part-I Foods and their uses Part -II Plant Diseases and their control Animal Diseases and their control Human Body – all parts Germination of Seeds Classification of Plants Classification of Animals Oxygen Cycle Carbon Cycle Nitrogen Cycle
Specific Gravity Specimen Cylinders with Hooks
Pulley Single
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
Oscilloscope
This Oscilloscope is corresponding to horizontal with small size. The bandwidth of Y axis is DC 10 MHz and the deflection factor is 5 mV – 5 V / div. It can be up to 50 V / div. using with the 10:1 probe. Sweep deflection factor is 0.1 ?s / div.
(1) Single Channel Single Trace Oscilloscope
(2) Bandwidth : 10 MHz
(3) Confirms to EN61010-1 (1993) and EN-IEC61326-1(1997).
(4) Wide measurement
(5) High sensitivity and trigger lock
(6) Sweep switch adopts digital code switch and accuracy
(7) Proper to use in colleges and for engineers and technicians
(8) Deflection factor is 5 mV – 5 V / div in 1-2-5 Sequence in 10 steps
(9) Accuracy: ±5 % (
10) Maximum Input Voltage: 400Vpk
(11) Sweep deflection factor is 0.1 us / div to 0.1 s / div
(12) Accuracy: ±5 %
(13) Trigger Sensitivity: INT:1.5 div EXT:0.3 V
(14) Trigger mode: INT, EXT, LINE, TV
(15) Trigger Sweep Mode: NORM, AUTO, TV. LOCK.
(16) Calibration Signal: 0.5 V Square wave of 1 kHz.
(17) CRT Effective working Area: 8 x 10 div. 1 div = 6 mm.
(18) Auxiliary Power Supply: 220V AC 50Hz
Pipette Pump
fast release Pipette Pump for precise pipetting & zip quick emptying.
The Knurled thumb wheel can be rotated to draw up or dispense liquids while the releaser may be pushed in for zip-quick emptying.
The moulded chuck has silicon rubber coller inside to hold various pipettes of standard sizes.
The Pipette Pump resists acids & alkalis and can be easily disassembled for thorough cleaning.
Material : Acrylonitrile Butadiene Styrene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Pipette Pump 2 ml | 12 | |
| Pipette Pump 10 ml | 12 | |
| Pipette Pump 25 ml | 12 |
Digital Viscometer
Description
Digital Viscometer Ensuring proper fluid viscosity is key in process environments. Achieving this requires an accurate, reliable, and durable in-line viscometer capable of monitoring fluid viscosity with minimal operator involvement. The Cambridge Viscosity VISCOpro 1600 viscometer is an ideal digital viscometer for this application due to its high accuracy and reliability, as well as its inherent ruggedness. The VISCOpro1600 viscometer can be used alone or in a multi-channel configuration controlled by a touch-screen display. This digital viscometer provides continual viscosity monitoring you can rely on. It is a compact instrument for applications where minimal operator involvement is desired. This digital viscometer features an optional LCD display for monitoring of critical fluid conditions. It also can be connected to a programmable logic controller (PLC) for seamless integration into a proprietary data management system. The units sensor and electronics are encased in an explosion-proof housing for durability and reliability. Due to Cambridge Viscositys patented technology, only a very small amount of fluid (1 ml) is required to obtain an accurate reading. Due to the small sample size needed and its automatic operation, the VISCOpro 1600 helps to maximize the efficiency of your process line and minimize waste. In addition, it works with most Cambridge Viscosity in-tank or in-line 300 series or 500 series sensors, giving you the flexibility to choose from a range of high-quality, maintenance-free options.
Magnetic Stirrer with Hot Plate
Maximum speed 1200 RPM.
Suitable for stirring all volumes, supplied with a teflon coated magnetic stirring bar.
