XTEMOS ELEMENT
AJAX PRODUCTS TABS
Plates For Simple Cell
Air Conditioning Trainer Window Type
Window air conditioner is becoming now a day’s necessity. The unit demonstrates the application of window air conditioner & evaluation of its performance. It consists of a small room to which a small air conditioner is connected the room is provided with a transparent front cover with a heater inside to simulate heat load in the room. Various measurements are provided so that performance of system that is COP of system, actual & theoretical cooling capacity of system & power consumption of unit with different load conditions.
SPECIFICATIONS:
1.Compressor – Hermetically sealed, Kirloskar make, having the capacity of 1/10 ton of refrigeration using R-12 refrigerant to keep room temperature between 20 to 30 c. 2.Condenser – Finned tube type, with forced air flow over the tubes, 3.Capillary tube of matched length as expansion device. 4.Evaporator – Finned tube type with forced air flow, 5.Room – 0.6 X 0.7 X 0.7 m. height, provided with transparent front wall. A heater with input control is provided inside the room. Which simulates different load conditions. 6.Measurements and Controls a) H.P. / L.P. Pressure gauges b) Digital temperature indicator to measure the temperatures at various points. c) Energy meters to measure input to compressor & heater. d) High and low pressure cutout. e) Thermostat to put off the compressor at set room temperature. f) Necessary switch for electrical components.SERVICES REQUIRED:
1.Floor area of 2m X 1 m. 2.230V, 15AC stabilized supply with earthing connection
Submercible Pump Test Rig
DESCRIPTION:
The Set-up is designed to study the performance of Submersible Pump. The Set-up consists of a Submersible Pump coupled with electrical motor, supply tank, measuring tank & pipe fittings for closed loop oil circulation. Pressure and Vacuum Gauges are connected on delivery and suction side of pump for the purpose of measurement. The flow rate of water is measured using measuring tank and stop watch provided.EXPERIMENT:
1. To determine overall efficiency and pump efficiency of the Submersible Pump 2. To plot Head vs. Discharge, Pump efficiency vs. Discharge.FEATURES:
1.Closed loop water circulation 2.Compact & stand alone set-up 3.MS Excel sample calculation program on demand 4. Stainless Steel tanks and wetted parts 5. Superb painted structure 6.Simple to Operate & MaintainUTILITIES REQUIRED:
1.Electric Supply: – Provide 230 +/- 10 VAC, 50 Hz, Single Phase Electric Supply with proper earthing. (Neutral – Earth voltage less than 5 VAC), 5 A, three pin socket with switch for pump. 2.Water Supply: Tap water connection ½ “ BSP, Distilled water @ 90 Ltrs. (Optional)TECHNICAL SPECIFICATIONS:
1.Product : Submersible Pump Test Rig 2.Pump & Drive : Submersible Pump, Capacity 1 HP 3.Supply Tank : Capacity 90 Ltrs. MOC SS 4.Measuring Tank : Capacity 60 Ltrs. MOC SS fitted with Piezometer Tube & Scale 5.Piping : GI / PVC 6.Stop Watch : Electronic 7.Control Panel : With required electrical instrumentation The whole Set-up is well designed and arranged in a good quality painted structureXTEMOS ELEMENT
AJAX PRODUCTS TABS SIMPLE
Fuel Supply System Diesel CRDI Type
Fuel Supply System Diesel CRDI Type (Actual Working Model) Common Rail Direct Injection.
This is an actual working model of fuel supply system of a CRDI diesel engine. The parts details is as under ::
This is an actual working model of fuel supply system of a MPFI petrol engine. The parts details is as under ::
1. Fuel Tank
2. Fuel Filter
3. Motorised Fuel Pump
4. Pressure Gauge
5. Fuel Rail
6. Fuel Injectors
7. ECU
8. Power Supply
9. Fuel Gauge & Control Panel
This model helps the student to understand about the parts & working of CRDI system. It is specially designed for demonstration purposes. The model will be supplied with key card & very interesting literature regarding working.
LABORATORY AND MEDICAL MONOCULAR MICROSCOPE
PRODUCT DESCRIPTION:
Being a leading firm in this industry, we are deeply engaged in offering a high-quality range of MS 30 Medical Monocular Microscope.
Details:
- MS-30 Student Monocular Compound Microscope
- Viewing Body Monocular tube, Straight,
- Stand Monocular, frame inclines back to 90°
- Eyepiece eyepiece 10x
- Nosepiece Quadruple revolving Nosepiece
- ObjectivesSA series Achromatic objectives 10x/ NA 0.25 , 40x/ NA 0.65 (SL) , 100x/ NA 1.25 (SL, Oil)
- Stage Stage plate size 124 x 120mm with Mechanical stage for X and Y movement of slide up to 30 x 75mm with graduated scale and Vernier’s
- Focusing Separate coarse and fine focus controls. Coarse movement by Rack & Pinion and fine movement by Screw Lever Mechanism
- Condenser Sub-stage Iris diaphragm with moving up and down through rack and pinion, condenser NA 1.25 with Blue Filter
- Illumination System Plano concave reflector mirror mounted at the base
- Package Contents Thermocole Box, with operation manual, dust cover and cleaning cloth
Conical Friction Clutch Working Model
XTEMOS ELEMENT
AJAX PRODUCTS TABS ALTERNATIVE
Fashion
Band Brake Working Model
Balance Compression
5000g capacity with 25g subdivisions
Zero adjustment knob
Includes: (1) Balance
Balance Compression, Capacity 5 Kgs.
(1) Balance
Useful for weighing chemicals and general purposes. Made of plastic body with wide view dial and easily readable scale.
Most durable and provided with zero adjustment knob.
Cap : 5kg Sub division : 25g
Advanced Universal FPGA Trainer
The universal FPGA trainer consist of a main board with many peripheral like USB Device, Ethernet, Serial ports, Parallel Port, VGA port, Graphics LCD, Switches, LED, ADC etc. This motherboard has 4Nos of high speed connectors for plugging the daughter boards, which contains the FPGA of any manufacturers. Separately 2Nos of 100 pin high speed connectors provided for hardware expansion as plug in boards.
• Industry standard interconnection
- 10 MBPS Ethernet
- USB 2.0 Interface
- Two RS232 ports
- 9 pin D connector
• Memory Sub system
- 8 MB x 16 Bit SDRAM
- 4MB x 16 bit flash EEPROM
- 256KB I2C EEPROM
• Additional Features
- One 240 x 128 graphics LCD
- 16 Nos of dip switches
- 16 discrete LEDs
- 4 digit multiplexed 7 segment LED display
- 4 x 4 matrix keyboard
- One VGA Port at 15 pin D connector
- One PS2 connector for keyboard and mouse
- Reset Switch
- I2C Real time Clock
• Analog Input & Output
- 2MSPS SPI ADC (12 Channel)
- Temperature sensor interface
- One 16 bit Stereo CODEC
• 2 Nos. of 100 pin high speed connectors provided to hardware expansion can be used as hardware bus.
• Multilayer board for superior signal integrity.
• 54 I/O pins terminated at 3Nos of 20 pin connector for external interfacing.
Clinometer Compass
Description
Clinometer Handle Compass is a reproduction of an antique Clinometer compass. The Handle Compass gets its name from its "handle" shaped sight, which actually serves two purposes With the compass level, an object can be viewed through the peep sights to determine its magnetic heading. The second and most interesting purpose is when tilting the compass on its side and viewing an object through the sights, its angle of elevation or declination can be found. A weighted pendulous arm beneath the compass needle can be read from one of three scales : Angle in degrees beneath the zenith (from straight up), angle in degrees of elevation or declination, and in inches per yard of slope. The compass has a needle lift mechanism to protect the compass jewel and the pendulous arm when being transported.XTEMOS ELEMENT
AJAX PRODUCTS TABS ARROWS PAGINATION
Fluid Mechines Hydraulic Machines Models
FLUID MECHANICS & HYDRAULIC MACHINES MODELS
1. Hook Gauges
2. Venturimeters & Orificemeters
3. Manometers
(A) Pitot Tube
(B) U Tube Double Column Manometer
(C) Differential Manometer
(D) Inclined Manometer
4. Valves Models
(A) Hydraulic Non Return Valve
(B) Gate Valve
(C) Globe Valve
5. Turbines & Pumps Models
(A) Different Impellers Of Pumps And Turbines (Set Of 8) :
(i) Mixed Flow Runner Cast Aluminium
(ii) Axial Flow Runner Cast Aluminium
(iii) Radial or Centrifugal Runner Cast Aluminium
(iv) Kaplan Runner Cast Aluminium
(v) Francis Runner Cast Aluminium
(vi) Domestic Self Pumping Runner of Brass
(vii) Centrifugal Runner Actual Cast Iron
(viii) Pelton Wheel Runner Cast Aluminium
(B) Display Board For Pipes
(C) Hydraulic Elevator:
(D) Hydraulic Ram Non Working Model
(E) Pelton Turbine Model
(F) De-Lavel Turbine Model
(G) Kaplan Turbine Model
(H) Francis Turbine Model
(I) Impulses Turbine Working Model
(J) Air or Steam Pressure Turbine Model
(K) Pure Reaction Turbine Model
(L) Radial Turbine Model
(M) Gear Pump Model:
(N) Rotary Pump
(O) Centrifugal Pump : Actual Cut Section
(P) Reciprocating Pump : Actual Cut Section
(Q) Model Of Air Lift Pump Model
(R)Pendulum Pump Model
(S) Archemedian Screw Pump Model
(T) Tubewell Model :
(U) Deep well Turbine Pump Model
(V) Submersible Pump Model
(W) Hydro-Electric Power Installation Model
Ice Melting Kit
Description
Demonstrates the difference in thermal conductivity of two different materials. The kit consists of two identical blocks, one made of aluminum and other made of plastic. When an ice cube is placed on aluminum it turns into water in seconds, while on plastic block it melts slowly. The aluminum block has a larger heat capacity and a higher thermal conductivity while the plastic block has lower values of both parameters. With instructions.
Resistance Units
XTEMOS ELEMENT
AJAX PRODUCTS TABS WITH ICONS
Sieve Shaker Electrical Table Model (Only For 8” Dia Sieve)
Sieve shakers are used to measure particle size as part of your research or quality control applications.
Sieve shakers provide uniform motion to ensure the reproducible results you can’t get from hand sieving. Electrically operated Fitted with Electric Motor inside the Body having speed regulator to increase of discrease the vibration. The table sieve shaker having the capacity of 8 Sieves.
Conductivity Appratus Ingen – Hauzs
Description
Consists of 5 metal rods of different materials having equal lenghts mounted in sheet metal box 150 x 90 x 100mm with corks. Metal rods 150 x 3 mm length x diameter, one each of aluminium,brass, copper, lead and iron, embedded along one side of a metal tank size 150 x 90 x 100 mm length x width x height.
XTEMOS ELEMENT
AJAX PRODUCTS TABS LOAD MORE PAGINATION
SILICA CRUCIBLE WITHOUT LID
PRODUCT DESCRIPTION
- Crucible is glazed inside and outside.
- Highly resistant to alkalis and hot temperatures
- 50ml capacity
- Outside diameter 55mm, 42mm height
- No lid includedSilica crucible is glazed inside and outside. Highly resistant to alkalis and hot temperature SIZES ARE: 15ML 25ML 50ML 80ML 100ML 150ML
SILICA CRUCIBLE TALL FORM Without Lid, Translucent
XTEMOS ELEMENT
AJAX PRODUCTS TABS CAROUSEL
FISHER CLAMP (Burette Clamp)
PRODUCT DESCRIPTION
These Clamps are moulded in Polypropylene making it completely
corrosion-proof. The spring loaded jack in themiddle provides a vice likegrip to the Burette and prevents it from slipping. Two tapered wedges areprovided to ensure firm grip on rods having dia 3/8” or 1/2”.
Available in 2types:
- Single
- double
Metacentric Height Apparatus
DESCRIPTION:-
A pontoon is allowed to float in a small tank having a transparent side. Removable steel strips placed in the model for the purpose of changing the weight of the model. Displacement of weight is measured with the help of a scale. By means of a pendulum (consisting of a weight suspended to a long pointer) the angle of tilt can be measured on a graduated arc. For tilting the ship model, a cross bar with two movable hangers is fixed on the model. Pendulum and graduated arc are suitably fixed at the center of the cross bar. A set of weights is supplied with the apparatus.EXPERIMENTS:-
Ø Determination of the Metacentric height and position of the Metacentric height with angle of heel of ship model.TECHNICAL SPECIFICATION: –
Ø Pontoon : Size 300 x 150 mm (Approx.) with a Horizontal Guide Bar for aliding weight. Ø Material : Stainless Steel Pontoon Ø Water Tank : Size 600 x 400 x 400 mm (Approx.) Ø Front Window of Tank : made of Glass/Perspex Ø A set of weights is supplied with the apparatus. Ø The whole Set-up is well designed and arranged in a good quality painted Structure
Reagent Reservoirs
The Universal Reagent Reservoir is a graduated single reagent reservoir with maximum volume of 50 ml, reservoir with 8 separate numbered 5ml.
Reagent channels & a reservoir with 12 separate numbered 5ml. Reagent channels.
Made of polypropylene these reagent reservoirs are repeatedly autoclavable and can be used with all multi-channel pipettes.
Material : Polypropylene
| Particulars | Pack (Pcs) | |
|---|---|---|
| Reagent Reservoir 75 ml | 12 |
